Search Documents

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

By Alexander May

The U.S. Bureau of Mines investigated the application of oxidation-reduction potential (ORP) and pH measurements to environmental studies of mining and mineral processing wastes, and developed a computer program to estimate the concentrations of species of lead present in samples from a lead processing waste site. The methods and techniques for the ORP-pH measurements were investigated using known standard solutions made in the laboratory, samples from a ferric oxide waste disposal pond at a rutile production plant, and samples of well water and stream water from the lead processing waste site. ORP values were measured from 5 to 80 °C, from pH 1 to pH 12, and at various ratios of oxidant to reductant. The ORP-pH values can help identify valence values and species of ions present, including those of major, minor, and trace concentrations, and also indicate possible reactions at various pH values. The ORP measurements versus temperature yield data from which thermodynamic values can be calculated. The application and limitations of these measurements are discussed, and a brief discussion of the computational program to identify species of lead is presented.

Jan 1, 2010

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By John S. Berber

Acids, neutral oils, and pitch were produced by distillation of low-temperature lignite tar and processed to upgrade them into more valuable products: The acids were separated from the distillate and catalytically dealkylated to produce phenol, cresol, and xylenol. Aromatic and naphthene fractions of the neutral oil were converted into phthalic and maleic anhydrides by catalytic hydrodealkylation and vapor- phase oxidation. Paraffins and n-olefins from the neutral oil were processed into alkybenzene sulfonate, a biodegradable substance. Aromatic materials from the neutral oil were also extracted with organic compounds and the extract hydrogenated under pressure to produce jet fuel. The pitch was processed by various means to change its characteristics and make it suitable for similar applications as high- temperature tar pitch, including preparation of carbon black and metallurgical electrodes. In most cases, products obtained from the low-temperature tar were examined for physical and chemical characteristics and for potential commercial utility. Information obtained from this research would be helpful if a new coal- chemical industry based on tar utilization were established.

Jan 1, 1973

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By B. W. Naugle

A small-scale laboratory coke oven similar to those described by Swiniarski, Cryan, and Altieri and Fuchs, Sandhoff, Taylor, and Gauger was built by the Bureau of Mines in 1943. Tests made since that time have indicated that such a small oven is of questionable value in predicting the coking pressures to be expected in commercial coke ovens. This summary of the work done has been prepared at the suggestion of the Advisory Committee to the Bureau of Mines-American Gas Association Survey of Carbonizing Prop¬erties of American Coals.

Jan 1, 1948

By N. F. Le] [Jaune

[ ]

Jan 1, 1923

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By J. R. Hoskins

A recent survey of 23 vein-type metal mining operations in several western states discloses that some of the more serious deficiencies in ventilation technology are associated with inordinately high levels of mine resistance. This problem has progressively increased over many years of operation (without adequate remedial action) as mines have become extended in depth. Where two shafts form the downcast and upcast airways of a relatively deep mine, the whole of the mine air volume must pass through each shaft in turn. Since at least one of these shafts contains hoisting equipment, structural members are necessary to support the rigid guides and shaft walls. These offer high aerodynamic resistance. In some deep mines, a single shaft of this nature may represent upwards of one-half of the total mine resistance. The second shaft, depending upon its design, may represent an additional one-third of the mine resistance. Therefore, the various working levels throughout the mine contribute only the small remaining amount of the total mine resistance.

Jan 1, 1972

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By Robert C. Gabler

Evaluation of incinerated sewage sludge as a secondary resource for aluminum, phosphorus, and minor constituents such as copper and zinc was initiated as part of the Bureau of Mines secondary resource program. The elemental composition of sludge ash for 14 plants in 11 U.S. cities was determined. Comparing industrialized cities with cities where most of the sewage is domestic, significant differences in heavy metal content were noted. Various parameters were investigated affecting the extraction of metals and phosphorus from a typical industrial city sludge ash and from a Palo Alto, Calif., sludge ash with a high precious metal content. Three extraction-recovery procedures for metals and phosphorus using sulfuric acid leaching, ion exchange, and various precipitation techniques were investigated. The last procedure developed was a combination approach using a three-stage countercurrent sulfuric acid leach that recovered most of the economic values from the sludge ash and also removed the leachable fraction of elements of environmental concern.

Jan 1, 1979

By James M. Stuckey

In a search for improved methods of upgrading tar obtained by low-temperature carbonization of coal, monoethanolamine (MEA) was found to be effective in extracting tar acids from coal tar distillates derived from a subbitunwous and a lignite coal. Patch extractions showed that both yield and purity of the extracted acids improved with increasing volume ratios of monoethanolamine to tar acid, varied from 1:4 to 8:1. Yield improved, but purity decreased as the concentration of monoethanolamine was changed from 30 to 70 volume-percent, and as the concentration of tar acid in distillate was increased ad from 14 to 45 percent. In a continuous countercurrent extraction employing a double solvent (monoethanolamine and hexane) approximately 80 percent of the tar acids was extracted from 170° to 350° C. tar distillate when using 1.6:1 volume ratios of amine:tar acids. Tar acids isolated from his extract, although of improved purity, contained appreciable quantities of neutral oils and some tar bases. Aqueous monoethanolamine was not effective for extracting the last 10 to 15 percent of tar acids in 170° to 350° C. distillate oil from lignite coal. The highest yield of isolated tar acids and the best recovery of monoethanolamine were obtained by diluting the extract with water and saturating with C02. Some losses of solvent were encountered when aqueous monoethanolamine solutions were heated through decomposition of the amine with the liberation of ammonia.

Jan 1, 1960