Search Documents

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By David R. Alison

This study was conducted using field interview methods to determine the data and information requirements of the underground coal mining industry for improving mine ground control procedures in existing and future mines. The establishment of a central geologic and engineering information resource center with computer searchable abstract files that can locate and supply descriptive and case-study literature addressing specific mining problems is recommended. Research done under Bureau of Mines Contract J0395010, includes a Bibliography of Underground Coal Mine Ground Control Literature.

Jan 1, 1980

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau&apos;s annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By William F. Hahn

This project focused effort on three separate areas: demonstration of a low seam longwall illumination system, design of illumination systems for low coal auger miners, and an assessment of machine lighting systems for machinery used to mine low seam coal. Results indicated illumination systems can be purchased by the mine operators of low coal seams. These systems can be supplied with the equipment as a factory integrated system or can be retrofitted to the machine or longwall equipment.

Jan 1, 1982

By H. D. Kline

This paper describes the methods of mining and washing brown iron are in 1957 at the Sawyer mine, leased by Wayne County Mining Co., and the Fore mine, leased by Four Mining Co., both in southern Missouri; it is one of a series prepared by the Federal Bureau of Mines on mining and milling methods and costs in various districts of the United States. The Sawyer mine is in Wayne County, about 10 miles north-northeast of Williamsville (fig. 1); the Fore mine is in Howell County, about 20 miles southwest of West Plains (fig. 2). Both are open-pit mines from which the crude are was upgraded by washing and hand-sorting to produce are of grade and quality suitable for sale to operators of iron and steel furnaces. The operations described are typical of many others that produce or have produced marketable brown iron are from small sedimentary deposits, several hundred of which outcrop on the crests or hill sides of southern Missouri (fig. 3). The 1957 production of marketable brown iron are by 40 separate operations in the southern part of the State was 281,427 wet long tons, valued at $1,637,243. Production from the Sawyer mine that year was 17,000 dry long tons of washed are, and from the Fore mine, 20,816 dry long tons.

Jan 1, 1960

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982

By L. A. Morely

Volume II of the final report concerns the application of sensitive ground-fault interrupters (GFIs) to ac utilization circuits in U.S. mines The main concepts examined are shock prevention and methods for reducing nuisance tripping. The research involved a literature search, input from previous Bureau of Mines contracts, and contacts with electrical manufac-turers and mining personnel. Following this background work, several devices that showed promise were obtained and tested. Results of testing indicate the existence of GFIs that may be modified to perform adequately on U.S. mining systems. A recommended set of guidelines is included in the report, covering design, construction specifications, and performance tests.

Jan 1, 1982

By C. Froger

Since its creation in 1950, the Centre d&apos;Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

By Ross W. Smith

Microflotation and surface chemical studies were conducted on a chromite from the Stillwater Complex in Montana and on some of the minerals usually found to be associated with such chromites. Considering the chromite it was found that aging the ground mineral in air or heating it markedly affected its flotation behavior. Much of the observed effects could be attributed to oxidation reactions involving surface chromium and iron species. Strongly acid pretreating the mineral appeared to reverse such effects. Thus, it can be concluded that the manner in which the mineral (or the ore) is pretreated is of utmost importance in its flotation. Work carried out on associated gangue minerals determined how they are likely to behave in a flotation environment and how certain foreign ions derived from a chromite ore itself can affect their surface characteristics and, thus, presumably also their behavior in a flotation circuit.

Jan 1, 1981

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Jesse L. Hoyer

A Bureau of Mines turbomill was evaluated for use in the production of high-purity, ultrafine x-Sic powders suitable for advanced ceramics that could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. The effect of milling param-eters, such as type of dispersant, temperature, pH, and gas environment, on the milling of x-SiC was studied. The addition of dispersants improved the grindability of x-SiC. Of the six dispersants studied, the best results were obtained with Mara-sperse N-22. Grinding efficiency was also increased when the x-SiC was milled in a basic slurry and at elevated temperature. Gas environments did not appear to affect grinding of x-SiC. Optimum grinding efficiency was obtained at 50° C in a slurry at pH 9.5 with Marasperse N-22 as the dispersant. Under these conditions, minus 100-plus 200-mesh x-SiC was ground to 80 pct less than 1 um in 4 h.

Jan 1, 1987

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By William E. Sopper

Heat-dried municipal sludge was applied to a barren burned anthracite refuse bank in 1974. Sludge was applied at rates of 0, 40, 75, and 150 dry metric tons per hectare" Ten species of trees were planted and five species of grasses and legumes were seeded for evaluation. One plot was also irrigated with sewage effluent. The 150 t/ha sludge application rate produced the best overall herbaceous vegetation growth response. The 40 and 75 t/ha sludge application rates produced the best tree seedling growth response. Foliar analyses for trace metals indicated no phytotoxity problems. Analyses of leachate water at the three-foot soil depth indicated that the sludge applications did not impair water quality. Results of the study indicate that treated municipal sludge can be used to revegetate land disturbed by mining activities without adverse effects on the vegetation or water quality.

Jan 1, 1978