Search Documents

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By John Vynne, John Hutchings

There have been a number of recent technological advances in instrumentation for blasthole drills, and more specifically in drill monitoring and HPGPS guidance systems. Likewise, great strides have been made in the development of drill and blast software systems which are user friendly, while providing far greater capability to accurately design and monitor drill and blast patterns.

Jan 1, 2011

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By Eric Roller, Elliott Giles

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009,one NA Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012

By Corry Goumans

Description of Project: Drilling, Blasting and Installation of Catenary Cables. Project Owner: Rio Tinto Alcan

Jan 1, 2010

By Robert Hopler

GEO. M. MOWBRAY’S REFRIGERATOR CAR FOR THE SAFE CONVEYANCE OF EXPLOSIVES. It is a fact well known to all miners who have used nitro-glycerin, or any of its adulterations, commonly known as dynamite, rendrock, Hercules’ powder, dualin, vigorite, etc., that when congealed, these compounds cannot be exploded, and in this congealed state — say at temperatures below 40° F. — they can be handled with no more danger than a box of soap or a can of lard. If, then, the atmosphere by which this class of explosives is surrounded, during transportation, be maintained below 40° F., explosion is practically annihilated. Therefore, I constructed a refrigerator car, with cells for every box of the explosive; and two years of railroad transportation confirms our ten years’ experience in teaming in wagons, that this class of explosives can be transported in perfect safety, as above described.

Jan 1, 2011

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Ravi Sahu, Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone.

Feb 1, 2020

By Timothy Fogarty, Gregory Poole, Roger Reeder, David Switz

This project involved the construction of a new pump station and intake structure at an existing water treatment facility. Although the project involved a significant amount of rock removal, the specifications said no blasting.

Jan 1, 2012

By Dr. Paul Worsey, Dr. Calvin Konya, Dr. Anthony Konya

Development of methods to calculate presplit blasthole pressures through simplified models, namely the Empirical Model and the Detonation Pressure Model. These models can be used with variations in explosive type and diameter, along with borehole diameter. All models have been validated with test data and shown to have minimal error.

Feb 1, 2020

By Dale Preece, Stephen Chung

The DMC-BLAST (Distinct Motion Code) has been developed for modeling bench blasting to one or two free faces such as choked blasting in surface gold operation and cast blasting in coal mining, respectively. This computer code has been used to assist the analysis of rock mass displacement after a blast was initiated in an orderly delay sequence. Applications of this feature can be found in the studies of dilution control in surface mining of gold as well as coal involving complex rock structures. Recently, DMC-BLAST has been modified to include a designated delay firing order coupled with variable rock strengths in the blasted media. This newly added feature allows the investigation of the effects of delay firing order on rock displacement in blasting a complex interbedded ore-waste structure. Examples of blasting a steeply dipping coal seams and bedded rock structure, especially in coal mining operations will be addressed and the comparison of efficiency in blasting in an up-dip as opposed to blasting in a down-dip direction will be discussed. Also covered in the paper is a new application of DMC-Blast to simulate a stope blasting underground. Simulations of blasting in a few selected types of timing/structure combinations will be presented in this paper.

Jan 1, 2000

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The University of Kentucky employs an explosively driven shock tube in the course of experimentation. A good deal of the work completed relates to the verification of blast mitigation products and strategies. The work is dependent upon reliably reproducing specific pressure time histories called out by the test in question. The facilities are located in the workings of an underground limestone quarry in Georgetown Kentucky. As such, the temperature maintains fairly consistent 60°F (15.6°C), making it a comfortable work environment year round. Unfortunately, the relative humidity follows the prevailing weather conditions allowing a wide variation, especially between the winter and summer seasons. A study was undertaken to gauge the influence of relative humidity on shock wave generation, including the positive and negative phases of the wave.

Jan 1, 2011