Search Documents

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Panagiotis (Takis) Katsabanis, Lyall Workman, Jack Eloranta

The reduction of metallic ores to concentrate consumes a great deal of electrical energy. In the past two decades, a number of case studies have demonstrated a beneficial relationship between powder factor and grindability. However, changes in mill performance cannot be attributed to changes in feed size alone. Blasting energy and the distribution of that energy appears to affect subsequent comminution beyond crushing. This experience has prompted researchers to attempt to duplicate and quantify the mechanisms involved. To date, published reports indicate a measure of success. However, the blast engineer and the mill engineer still lack the tools and basic understanding necessary for full drill to mill optimization.

Jan 1, 2015

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By Gordon Lovegrove, Jeffrey Leob, Dwayne Tannant

It has long been known that the combination of aluminum (AL) powder to ammonium nitrate (AN) / fuel oil (FO) can greatly enhance fragmentation or ultimately reduce the number of blast holes in a pattern. Decades of research have meticulously provided optimal AL:AN:FO ratios showing dramatic increases in energy output levels, yet widespread use of aluminized ANFO (ALANFO) has yet to replace the use of ANFO in the blasting world today. This may be due to the perception that the upfront, increased cost of materials deters the selection of this advantageously modified explosive. Researchers have explored this question and promote ALANFO by pledge of massive reductions in day-to-day operational costs. However, in these analyses there is a complete disregard for the external costs of the material; the environmental effects and sustainability considerations of the product. A holistic social cost-benefit analysis of ALANFO shows that an admittedly high-cost explosive does indeed provide an output which contains a wealth of operational savings in typical blast patterns. However, the immediate, on-site costs and savings do not define the limitations of this analysis. A complete comparison of the externalities including the environmental and sustainability considerations of the aluminum by-product life-cycle, and the environmental impacts of both the refinement of ammonium nitrate prills and the acquisition of sufficient fuel oil are also assessed. A savings of $216,000 / year through the use of ALANFO in one particular case study was recalculated to an increase in drilling and blasting costs of $188,000 when the external costs of aluminum, ammonium nitrate, and fuel oil are included analysis. The results of this analysis are intended to improve contractors? selection of explosives by providing additional societal and environmental factors into the equation, in preparation for an exponential global shift to greener business operations, while allowing them to remain competitive.

Jan 1, 2011

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Les Willan, Chris Batten, Matt Sparkes

In late 2008 Xstrata Newlands Coal Mine in Central Queensland and Orica Mining Services engaged in discussion to investigate methodologies to change their current mining practices and overcome the issues in the mining of steeply dipping coal seams, the associated coal loss risk and to assist in improving mining productivity. A strategy was developed and it was determined that through-seam blasting was essential to the success of winning the coal from the Wollombi Pit at Newlands.

Jan 1, 2010

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Jorge Cárdenas Miranda, Hector Espinoza

Currently in open pit mining in Peru with double bench, it is a challenge to optimize fragmentation in the drill rows near to the slopes to ensure the performance in the loading and haulage operation along with the process in the plant. That is why the present paper addresses a previously unanalyzed variable on the effect of the discontinuity plane on the fragmentation results. From the numerical mathematical models applied through algorithms in advanced computational tools such as Elfen, it was quantified the improvement in fragmentation results as P80 through a correct pre-split plane both in its extension as well as in its width. The first results show an improvement of 30% in the P80 and ensuring the quality of the walls without damage to the matrix of the final wall. The basis developed in this paper is based on the concept of wave reflection in the free face zones where greater efforts are presented for fragmentation, a similar theory is presented in the variation of initiation sequences that seek a greater area of reflective planes in the form of "V". Cases were evaluated with a percentage of compliance of the pre-split planes from 0 to 100% evaluating the impact on the results and correlated with field information explaining the behavior and validating the benefit. From the quantification of the benefits, this work opens the possibility of focusing resources on optimizing the pre-split process to achieve an improvement in the fragmentation results, giving a greater tool in the decision to optimize the blasting process.

Feb 6, 2023

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By THOMAS BAMFORD, Dale S. Preece, Amir Behbahanian, Mick Lownds

An important aspect of blasting is rock movement and final muck configuration. Computer modeling of this process has been done in 2D for many years, revealing insights into the blasting process and enabling some design optimization. Since blasting is inherently a 3D process, 2D modeling misses the 3D aspects of blasting results and can lead to inaccurate conclusions. Software development environments in many fields are evolving in 3D, enabled by steadily increasing computer speed, memory, and software efficiency. These same environments are also available for modeling of many physical processes, including rock blasting. This paper documents the development of 3D blast movement modeling techniques that utilize 3D computational mechanics and modern computing environments to predict explosive induced movement of hundreds of thousands of distinct cubic elements representing the rock mass. Blast induced ore travel and final location can now be predicted with reasonable accuracy and acceptable run times. The importance of Energy Partitioning was documented and demonstrated by GEM-2D (Geologic Element Motion) at the ISEE conference in 2024. This software is titled GEM-3D and includes this Energy Partitioning capability. This paper documents a GEM-3D example of ore movement during rock blasting and demonstrates ore dilution as well as the final location of different rock types as influenced by the blast.

Jan 26, 2026