Search Documents

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By Joshua Hoffman, Rhys Baker, Tim O’Brien

Numerous agencies in the Executive Branch of the United States Federal Government have regulatory jurisdiction over the explosives industry. These agencies develop the rules by which the explosives industry must operate, and many have the authority to enforce those rules. Likewise, there are entities in the Legislature that have oversight of those agencies and develop the laws that agencies must operate under. These entities in the Legislative Branch are Congressional Committees. Each committee has their respective jurisdictional authority over various agencies and issues. There are several Congressional Committees with jurisdiction over the agencies that govern the explosives industry and they differ slightly between the House of Representatives and the Senate. This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms. Options for civic involvement for engaging each of these bodies of power in their respective processes are presented. The differences between legislation and regulation are highlighted along with the processes by which each are promulgated. A proper understanding of the governmental mechanics that affect the explosives industry are critical for the industry to be able to be proactive in playing a role in these processes in a democratic way.

By Larry R. Fletcher

The Bureau of Mines obtained blasting accident data from the Mine Safety ant Health Administration (MSHA), U. S. Department of Labor. These data were analyzed to determine the most frequent causes of accidents in mine blasting. Accident totals for 1971 through 1981 are tabulated for metal-nonmetal and coal mines both surface and underground. In the past 11 years (1971-1981, inclusive) there has been an annual average of 9 fatal and 121 nonfatal blasting accident victims. Underground mining averaged 6 fatal and 93 nonfatal injuries each year.

Jan 1, 1983

By S. Huang, K. Xia

The down-stream size reduction processes such as crushing, grinding and milling, represent major expenditure of energy. The present study is aimed at linking the fragmentation characteristics of the rock feed in a crusher with the physical and mechanical properties of the rock and the energy expended in the process. This is done through a modified Hopkinson Pressure bar apparatus, where both the impact velocity and energy input can be carefully controlled. A single layer of rock particles of very narrow feed size range (9 mm - 12 mm) and occupying a fixed volume in a chamber is impacted by means of a striker. The resulting fragment size distribution is determined for two different rock types (e.g. a granite and a limestone), involving single and multiple impacts, with all other experimental parameters remaining constant. The progressive reduction in overall product size and detailed fragment size distribution curves are obtained through sieve analysis, for specified number of impacts. The resulting fragment size distribution is analyzed in the light two distribution functions, Rosin-Rammler and Swebrec.

Jan 1, 2015

By R L. Calhoun

A paper on High Pressure Air must start with the industry accepted definition of High Pressure Air and, for the reader who is unfamiliar with High Pressure Air systems, include basic information on which type of Drilling Rigs can benefit from the use of High Pressure Air. The operation of a modern Downhole Drill must also be reviewed.

Jan 1, 1976

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Andrew F. McKown

Overbreak and damage to rock walls at the perimeter of rock excavation can lead to safety problems due to rock falls and additional costs due to a] extra mucking, b] extra concrete or shotcrete to backfill overbreak, c] additional rock reinforcement, d] additional water inflow and e] additional maintenance of rock walls. To minimize these undesirable effects, there are several perimeter control techniques available (i.e. line drilling, cushion blasting, pre-splitting, smooth blasting, and fracture control blasting) which control perimeter hole spacing, burden and loading to provide a smooth, stable excavation contour. Conventional perimeter control loading and hole spacing is satisfactory for massive, homogeneous formations, but when blasting in weathered or fractured rock closer spacing and very light loading is required.

Jan 1, 1984

By D O. Doehring, W A. Charlie, W A. Lewis

The detonation of explosive charges releases large quantities of energy that can produce rock and soil deformations far from the detonation point Extensive data are available on blasting in general and on the performance of certain structures subjected to blast vibrations. However, only limited information is available on the performance of earthfill dams and other hydraulic structures subjected to blasting. The limited data indicate that, whatever the cause, one or several cycles of repeated strains in earthfill dams may cause residual porewater pressure increases. Limiting the peak particle velocity to less than 2.5 cm/s for operating dams constructed of or having foundations consisting of saturated, loose sands or silts and to less than 5 cm/s for other earthfill dams, should keep strains below the threshold strains required for residual porewater pressure increases to occur. Porewater pressures should be monitored throughout a blasting operation, and they should be allowed to dissipate, if necessary, before subsequent charges are detonated.

Jan 1, 1987

By D Larson, M Finger

Chemical explosives may become a key element in many of the in situ energy and mineral recovery methods under development. This paper discusses the potential role of explosives in deep rock mining for resource recovery. Several energy and mineral recovery programs described are an outgrowth of the Plowshare Program and Explosives R&D conducted as part of the AEC/ERDA mission at Lawrence Livermore Laboratory. Several important aspects of the use of explosives in deep rock mining are reviewed. First, the status of knowledge of deep rock fracturing to create permeability underground is discussed. Completely contained blasting has not been a widely applied tool used in the mining industry. We conclude that data available on deep rock fracture is minimal and that the mechanisms that control the processes must be understood before technical and economic feasibility can be established. We also discuss the unusual problems in the selection of an explosive or blasting agent for deep rock applications including emphasis on the functioning at depth and safety aspects. Finally, a brief review of similar activities within the U.S. is given.

Jan 1, 1976

By Doug Anderson

Two quantities, Peak Particle Velocity (PPV) and Scaled Distance (SD), have controlled aspects of many blasting projects and operations for a long time. Vibration criteria typically use both PPV and SD because they are simple to measure, and simple to calculate. Their use in regulations worldwide is fairly ubiquitous, in efforts to limit damage to structures in the neighborhood of a blasting operation. PPV and SD are also used to determine likely blast damage effects in mining operations.

Jan 1, 2018

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009