Search Documents

By M. Lundström, J. Aromaa, S. Seisko

"Gold dissolution was investigated in ferric chloride media, promoted as one of the most promising alternatives for cyanide-free gold leaching. The characteristics of gold open circuit potential (OCP) and its relation to gold dissolution rate was investigated. Furthermore, the reaction mechanism of gold dissolution in ferric chloride leaching was discussed. The effect of solution variables, [Fe3+] = 0.02–1.0 M, [Cl–] = 2–5 M, T = 25–95 °C and pH = 0–1.0, on OCP and dissolution rate were studied electrochemically using rotating disk electrode (RDE) and linear polarization resistance (LPR) method with ?cyc = 1000 RPM. The investigated gold OCPs in ferric chloride solutions were found to vary between 597 and 688 mV vs. saturated calomel electrode (SCE) and gold dissolution rates between 1.2·10–5–5.0·10–4 mol s–1 m–2. Increase in temperature (25–55 °C) and ferric concentration (0.02–1.0 M) changed OCP into more positive values, while increase in chloride concentration (2–5 M) decreased it. The logarithm of gold dissolution rate was shown to increase linearly with increasing OCP at the temperature range 25–95 °C, ferric concentration range 0.02–0.5 M and chloride concentration range 2–4 M. A notable increase in the gold dissolution reaction rate was evident at T > 55 °C. INTRODUCTION Currently cyanide leaching is the predominant method used in gold production from primary raw materials (Marsden and House, 2006). However, since the Baia Mare disaster in Romania in 2000, the use of cyanide has been the subject of international concern due to the toxic nature of the chemical posing a significant health threat if exposed to the ecological entities (Hilson and Monhenius, 2006; UNEP/OCHA, 2000). Therefore, several countries e.g., Costa Rica, Czech Republic, Germany, Hungary, Turkey, many states of the USA and provinces of Argentina, have started to ban or limit cyanidation via legislation (Laitos, 2012). Thus, alternative solutions, such as thiourea, thiosulphate, oil-coal agglomerates as well as halides have been investigated in order to replace cyanide as lixiviant (Adams, 2016; Aromaa et al., 2014; Aylmore, 2005; Hilson and Monhemius, 2006; Lampinen et al., 2015). Ferric and cupric chloride leaching have been reported to have advantage over cyanidation being capable to dissolve refractory gold minerals, without pre-treatment such as pressure oxidation or roasting (Angelidis et al., 1993; Lundström et al., 2014; Marsden and House, 2006; van Meersbergen et al., 1993). According to Aylmore (2005), 4% of publications for alternative lixiviants to cyanide in gold leaching were within category oxidative chloride processes including aqua regia and acid ferric chloride leaching. Further, some patents have been granted for ferric chloride leaching of gold (Abe and Hosaka, 2010; Lundström et al., 2016)"

Jan 1, 2018

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By P. Basarova

The attachment of bubbles onto a collecting surface is an ubiquitous natural phenomenon, playing a critical role in numerous practical processes. The goal of the project is to broaden the knowledge about hydrodynamic interactions between small bubbles and large solids that occur in nature and industrial processes. Focusing on collision processes between a single rising bubble (Db<1 mm) and a larger falling spherical particle in stagnant liquid, the theoretical model describing the bubble trajectory is given here. The model is based on analysis of forces acting on the bubble, and utilizes equation for the bubble motion. Mobile and immobile type of bubble surface mobility are considered. The calculated results are compared with the experimental data; here a high-speed video camera was used to capture the bubble motion and bubble-particle interaction. Very good agreement between experimental and calculated data was found. For both types of surface mobilities, the bubble deviation in the horizontal direction is nearly linear. The proportion constant is bigger for immobile bubble surface and increases with the bubble size. Furthermore, particular forces acting on bubble were studied. A similar course of relative bubble velocity and force impact was observed for identical bubble position. For cases when the bubble centre is close to the particle axis, only deflection in one direction is observed. When the bubble is reaching the maximum trajectory, the force ratio is changed. The bubble is firstly pushed away from the particle, but when it is within close distance from the particle, the bubble is pushed towards the particle.

Sep 1, 2012

By A. Usov

The studies carried out by the Russian researchers and those carried out jointly within some contracts with scientific organizations and companies of other countries, show that the electric pulse disintegration of materials (ED), proposed and investigated in detail in Russia (Kalyatsky, et al, 1980; Usov et al, 1987; Semkin et al, 1995; Usov and Tsukerman, 2000; Kurets et al, 2002) has been widely recognized and developed abroad (Andres, 1995; Inoue et al, 2000; Biela et al, 2008). The Russian and international journals and the proceedings of the conferences dealing with the electric pulse disintegration pay great attention to the principal principals of selective disintegration of materials. There is no, however, any information concerning both the technical means developed to implement the technique and the assessment of their performance, which would be necessary in objective assessment of the industrial use of the technology. The results of long-term studies of the technique and technologies of electric pulse disaggregation by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute "Mekhanobr"(S.Pertersburg) described. Exploratory stands and technological installations are developed to carry out pilot tests and operations under production conditions. Basic circuits and classification of technical means electric pulse disintegration of the materials are proposed, the analysis of transportation schemes and classification of the material in the disintegration apparatus are given, construction of chambers for continuous stadial disintegration of ores and materials are presented. The features and technological efficiency of electric pulse disintegration of various types of ores, and the spheres of effective use of the method have been determined. Keywords: electropulse disintegration, disintegration machines, chambers of comminution, stadial comminution.

Sep 1, 2012

By M. McClintock

"High Pressure Grinding Rolls (HPGR) is increasingly being chosen for comminution circuits for its energy-efficiency for hard rock mining operations. Despite HPGR’s growing popularity, geo-metallurgy programs are still prohibitively expensive because of large sample requirements. Traditionally, sizing HPGR application requires a significant amount of sample, in the order of 1 to 10 tonnes, depending on the level of study and complexity of the resource. Therefore, engineering and design of HPGR circuits typically are reliant on few composites that are required to be representative of the resource and mine plan. Three bench scale HPGR test methodologies were developed in 2015 at NBK Institute of Mining Engineering at the University of British Columbia (UBC) capable of defining the energy size breakage relationship of pilot HPGR. These methodologies were developed to allow bench scale testing for different levels of study from PEA (Preliminary Economic Assessment) to detailed design and operations. The Piston Press test defines the energy size reduction relationship by measuring specific energy consumption and corresponding feed and product size distributions. The advantage of Piston Press testing is the small sample requirement of 5 to 10 kg. Small sample requirements allow multiple samples to be tested across a deposit. Piston Press testing allows extensive geo-metallurgy programs that can determine ore variability and inform in optimization and production planning. To date, the Piston Press methodologies have been validated on a pilot-scale HPGR unit located at UBC. Recently, testing was conducted to calibrate and validate the Piston Press test against full-scale HPGR on a gold sulphide ore deposit. The program included the collection of operational data with the respective HPGR feed and recycle sample. Sample collected was used both for Piston Press testing and HPGR piloting. This paper discusses the test-work and results as carried out during this program, using the aforementioned methodologies."

Jan 1, 2018

By K. Amano, K. Haga, Y. Watanabe, A. Shibayama, A. Batnasan, A. Battsengel

"Apatite is an important host mineral in igneous and metamorphic rocks for production of phosphate fertilizers and phosphoric acid, and a potential source of rare earth elements (REE) production. For dissolution of REEs, sulfuric acid is better leaching reagent to develop the economical viable process for recovering of rare earth elements from apatite ore. However, the efficiency of rare earth elements dissolution in H2SO4 is about 30 % due to the formation of calcium phosphate or calcium sulfate as precipitate. On the other hands, phosphorus is mainly produced from phosphate ore. However, when treating rare earth elements containing phosphate ore, rare earth elements were discharged. Hence, development of novel apatite ore treatment process is required for effective utilization of natural resources. In this study, apatite deposit associated with REE was treated with sulfuric acid leaching and two stage precipitation by oxalic acid (C2H2O4) and magnesium chloride (MgCl2) for recovering REE and phosphorus, individually. Results showed that it can be seen the vast majority of La (87.5%), Ce (87.3 %), Pr (86.1 %), Nd (85.2 %) and Y (90.9 %) were dissolved in 1 mol/L diluted H2SO4 solution from the apatite ore. As average leaching rate of REE, over 85% of REE were leached by the condition. In the first stage precipitation using the obtained pregnant leach solution from leaching, over 90% of REE was precipitated by oxalic acid addition after controlling pH to 1 by NH4OH solution. After pH changed to 8.5, over 90% of phosphorus was recovered as precipitate by magnesium chloride addition in second stage precipitation"

Jan 1, 2018

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By Takaaki Wajima

The slag was attempted to be converted into the adsorbent for phosphate removal from aqueous solution using the alkali fusion method. The slag was mixed with NaOH powder (NaOH / Slag = 1.6), and then the mixture was heated at 600 ? for 6 h to prepare the precursor. The precursor was stirred at room temperature in distilled water to synthesize the adsorbent, and the removal ability of the obtained adsorbent for phosphate from aqueous solution was investigated. The products, including hydrocalumite and calcite, were synthesized, and the removal efficiencies of the adsorbent for F- and PO43- showed higher than those of raw BF slag, especially removal of PO43- are excellent (99 %), while the removal of Cl- , SO42-, NO3- and Br- was minor. The adsorbent could remove PO43- selectively in the co-existing solution of Cl-, NO3-, F-, SO42- and Br-.The equilibrium adsorption capacity of the adsorbent for PO43- was extrapolated using Langmuir and Freundlich models, and experimental data are found to fit Langmuir than Freundlich. The calculated maximum adsorption capacity of the adsorbent for PO43- is higher than other adsorbent reported previously. The high affinity of the adsorbent for PO43- in aqueous solution was caused by the formation of hydroxyapatite [Ca5(PO4)3(OH)] and brushite [CaHPO4?2H2O]. The prepared adsorbent is expected to be anew inorganic adsorbent for the removal of phosphate ion from wastewater. Keywords: Blast furnace slag, Alkali fusion, Phosphate removal, High selectivity

Sep 1, 2012

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By C. L. Tang

Parts of the wastewater are reused directly and the rest moderately purified and reused, so the utilization rate of wastewater of the whole processing plant reaches 100 percent. At the same time, beneficiation indicators have been improved stably, and great economic and social benefits have been achieved.

Jan 1, 2014

By N. A. Dementyeva

To improve gold recovery from preg-robbing carbonaceous ores a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon-in-leach (CIL) process for intensive cyanidation tailings and the recleaned concentrate was developed. The final flotation tailings are shipped to tailings disposal. Total gold recovery by the proposed technology from the ore with the head grade of 0.8 g/t was 83.9%. The gold loading onto the activated carbon from CIL process was 6.5 g/kg.

Jan 1, 2014

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By Y. Foucaud, I. Filippova, L. Filippov

Flotation is the most common beneficiation route for tungsten ores, but the predominance of minerals with similar surface properties poses a real challenge. This study investigates the use of Falcon centrifugal separators for gangue minerals removal and desliming prior to flotation. A typical tungsten-bearing skarn ore (Tabuaço, Portugal) is used, containing scheelite (CaWO4) associated with dense calcium-bearing silicates (vesuvianite), fluorite, apatite and light silicates (feldspars) as gangue minerals. Two types of Falcon bowls (Falcon UF and Falcon SB) were used, prior to flotation tests with fatty acids as collectors and a combination of sodium carbonate and sodium silicate as gangue minerals depressants. This flowsheet was compared with a reverse configuration, using flotation prior to Falcon concentrator, and with a classical flowsheet, using hydrocyclone and flotation. Gravity pre-concentration and desliming with the Falcon concentrator were optimized through the design of experiments (DoE) methodology. The influences of pulp density, rotational speed, feed flowrate and fluidisation pressure (for the Falcon SB) were studied for both bowls. Results showed that the Falcon can be used as a desliming and pre-concentrating apparatus. Separation performances depend mainly on rotary speed and pulp density for the Falcon UF, whereas rotary speed and fluidisation pressure are the main parameters for the Falcon SB. With only one stage of Falcon SB, an enrichment ratio of 7.9 is obtained with a 65% WO3 recovery while 89% of apatite and fluorite are rejected, which constitutes a very good selectivity. In comparison, Falcon UF shows lower enrichment ratios, around 2.7. In terms of desliming, Falcon UF is as efficient as the hydrocyclone, while the Falcon SB is significantly more efficient. Hence, the use of Falcon SB prior to flotation improves the overall performance of the tungsten flotation route by desliming the flotation feed while pre-concentrating the scheelite. It impacts very advantageously the flotation, as most of the calcium-bearing minerals are eliminated. A Falcon SB stage prior to flotation yields a final concentrate grade of 29.7% WO3 with a recovery of only 36.8 % that should be optimized as the reagents dosages were not adapted to the pre-concentrated feed.

Jan 1, 2018