Search Documents

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

By Shuoshi Lu

The Cu-Co ore studied here belongs to the oxide type. The oxidation rates of copper and cobalt are69.30% and 78.78%, respectively. The content of Cu in ROM is 1.34% and that of Co is 0.096%. The ore contains 4.64% carbon.Based on the process mineralogy and previous metallurgy tests, the principalprocess flow-sheet of ?grinding fines 80% -0.074mm, sulphide flotation followed by oxide flotation, and flash flotation for oxides? has been determined.The handling of carbon is determined through tests. The depressant PNL-1 depressed carbon effectively, improved the recovery of sulphide minerals and reduced the reagents consumption.The operation of the flow-sheet was also changed to better at the same time. Keywords: Cu-Co oxide ore, process mineralogy, carbon depression, efficient depressant of carbon

Sep 1, 2012

By V. A. Luganov

The processing of pyrite concentrates may be accomplished with a preliminary enrichment due to withdrawal of iron sulfides from initial concentrate. The withdrawal of iron sulfides is possible with the help of magnetic separation when the magnetic iron sulfides (pyrrhotites) separate from non-magnetic fraction?the sulfides of non-ferrous metals. The conversion of non-magnetic pyrite to magnetic pyrrhotites of adjusted structure occurs because of roasting with the withdrawal a part of sulfur. The resultant pyrrhotites are strong ferromagnetic with hexagonal structure. This paper contains results of studying magnetic properties of pyrrhotites, findings of the de-composition of initial pyrite with the consequence homogenizing of product and hardening of product of decomposition in liquid nitrogen. Define the type of pyrrhotites super lattice structure, was established that at increasing of sulfur contention the magnetic properties of pyrrhotites are change ? pyrrhotite begin evince the properties of antiferromagnetic material and magnetic susceptibility of material is interruptive changing from 0 to 1.7×10-3~1.9×10-3 SI units/g system. The paper contains results of technological researching of pyrrhotizing-magnetizing roasting of pyrite concentrates in different condition: in unoxidizing, with the decreasing contention of oxygen and in autogenous regime in air atmosphere. Established that the magnetic susceptibility of products depend of pyrite degree dissociation and achieve 2×10-3~3×10-3 SI units/g system at 40%~45% desulphurization. Defined the conditions of steady regime autogenous roasting, at resultant products possess coefficient of magnetization, and this can be used magnetic separation for separating ferromagnetic pyrrhotites from gangues and non-magnetic sulfides of non-ferrous metals. This technology of pyrrhotizing roasting is recommended for effecting in industrial condition. The initial materials and products of roasting subjected to chemical, thermogravimetric, Moss-bauer spectroscopy and X-ray analysis, defined the magnetic properties.

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"This work presents the results of the development of a flowchart for the processing of copper production dusts resulting in the production of of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.Dust having the following composition (wt. %): Pb 39.3, Zn 6.5, Cu 5.5, Stotal 10.8, As 1.05, SiO2 0.6, Cd 0.8, Bi 0.04, Ag 0.02, Re 0.03 was used in the work. Chemical and X-ray analyses indicated that lead, zinc and copper are generally present in dusts in the form of sulfates, various amounts of oxides, sulfides, silicates; sulfur (according to chemical analysis data) is present in the form of sulfates (~ 90%) and in the form of sulfides (~ 10%).Studies have been made on two-stage stripping of copper production dusts containing lead, zinc, copper, cadmium, rhenium in the form of various compounds, at first with soda solution, then with nitric acid solution. It has been indicated that the combination of the operations allows the recovery of 98% rhenium, 82% lead, 92% copper, and 96% zinc and cadmium each in the solution. Furthermore, at the stage of dust leaching with soda, 80% of rhenium and 0.01% of nonferrous metals each are recovered in the solution. Remaining quantities of all metals are recovered in nitric acid solution up to maximum values. Such behaviour of metals is caused by metal phase content in dusts and properties being formed during leaching of compounds. At the stage of dust leaching with soda solutions, carbonates with various compositions are formed due to the exchange reaction between nonferrous metal sulfates and sodium carbonate. The conversion of PbSO4 into PbCO3 is apparently occurs in the solid phase and the conversion of readily watersoluble zinc, copper, and cadmium sulfates into that of carbonate salts occurs in the liquid phase. Rhenium passes into solution due to the presence of rhenium greater quantity in dust in the form of readily soluble perrhenate. Some portion of the perrhenate is, probable, blocked by lead sulfate and liberated in the conversion of PbSO4 into PbCO3."

Jan 1, 2003

By Jacqueline Satur, Yoshiaki Kon, Buenaventurada Calabia, Xiao Sheng Yang, Arvo Naumanen, Kenzo Sanematsu, Sayaka Morita, Tetsuichi Takagi

Granite ores are composed of silicate minerals and a variety of valuable REE (rare earth elements)-bearing minerals, however the processing technique to recover these valuable minerals is not yet developed. In this study, the recovery of REE-bearing minerals by dry magnetic separation and wet high intensity magnetic separation (WHIMS)-settling from surface sample and from drill core sample, respectively, of a granitic REE-Zr-Nb ore deposit was investigated. The two samples have different mineralogy however in both samples, light REE are commonly contained in REE carbonate minerals while Y and heavy REE are commonly contained in zirconium silicate minerals and pyrochlore. The liberation size of the REE-bearing minerals in the two samples ranges from 10-250 ?m. Previous flotation testwork conducted on the drill core sample reported high recoveries of La2O3 (88%) and Ce2O3 (88%) but low recoveries of Y2O3 (42%), ZrO2 (17%), and Nb2O5 (29%). The objective of this study was to obtain higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling. Both processes implemented the application of a low magnetic intensity to initially separate the ferromagnetic minerals then a high magnetic intensity to recover the REE-bearing minerals. The results showed higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling indicating the potential of magnetic separation and gravity separation in recovering the heavy REE-bearing minerals. WHIMS-settling is more recommendable than dry magnetic separation because of its applicability in treating a wider range of particle size. In the WHIMS-settling, the light REE, Y, and Zr minerals were recovered mainly by applying four stages at high magnetic intensity of 21,500 gauss while the weakly magnetic pyrochlore was recovered mainly by decantation of the nonmagnetic slurry after a short settling time of 0.25 to 0.50 h. (MAX.300 words)

Jan 1, 2014

By S. Chuanyao

In last decade, along with its booming Chinese economy, China?s higher education has experienced rapid growth. In 2010, the number of various colleges totals more than 3500, with 2.2 million faculties registered. Currently there are almost 30 million students studying in the colleges, 3 times more than 10 years ago. Mineral Processing was initiated in 1949 as a sub-discipline of Mining Engineering, one of the 13 first level disciplines. Mineral Processing is now established in 34 Chinese colleges, recruiting 2600 undergraduate students, 540 postgraduate students and 100 PhD students every year. A further 9 institutes offer postgraduate education in this field. More than 3000 graduates majoring in Mineral Processing join the industry or institutions each year. The four-year undergraduate teaching and practical training in the colleges is designed to produce qualified mineral processing professionals. This includes courses in mathematics and natural science, fundamental engineering and basic and specialization courses. Recently, the ?Excellent Engineer Program? was launched to strengthen students? practical capabilities. This is a 3+1 teaching and training model; 3 years of theoretical course study plus 1 accumulated year of various practical studies, either inside or outside the college. As for graduate employment, mining-related major graduates have been in a good demand thanks to the intensive investment in mineral sector by Chinese companies. The shortage of experienced metallurgists generates a greater than 90% employment rate for Mineral Processing graduates. However, the biggest problem we are still facing is the gap between the quality of the graduates and the requirements of industry, as a result of occupation attraction, teaching systems, faculty quality, and so forth. Another problem is international orientation. Although nowadays Chinese-foreign cooperation in college education is popular, collaborative mineral related projects are far less common, leaving much room for improvement. Looking ahead to the next 10 years, we still have the right reasons to estimate continued prosperity in the minerals sector as well as mineral processing education in China. A brief analysis and views on this will also be shared in the presentation. Keywords: China, mining engineering curriculum, excellent engineer program

Sep 1, 2012

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

By M. Rehor

The importance of brown coal as a raw material is currently given by growing energy needs of Czech Republic. More than 70% of mined brown coal comes from North Bohemian Basin these days. Mining of brown coal is run in four mining locations. They are geologically different and the parameters of mining coal are quite different too. This requires a little bit different methodology of both extraction and reclamation. Methods of reclamation works in the region are given mainly by the characteristics of overburden rocks appearing in the upper horizon of recuperated localities. The difficulties of the North Bohemian mine dumps reclamation works are caused by extremely unfavourable properties of rocks poured down to the majority of mine dumps. These are mainly rocks of the overlaying strata and the rocks strata of brown coal bed. Main materials poured down to the mine dumps are sands, clayey sands and kaolin ? illitic clays. Admixtures in filled rocks consist of organic (coal) mass, siderite and pyrite. These rocks are mechanically instable with respect to the wind and water erosion and during weathering they are getting unfavourable, acid (phytotoxic) nature, due to the influence of SO3 and Al ions. External and internal dumps of open pit mines are significant part of the North ? Bohemian landscape sustained by excavation. Their as fast as possible preparation and gradual integration into ecosystem of the area is interest of both citizens of region and mining companies. The paper briefly summarizes the methodology of restoration of the largest dumps of the North Bohemian Brown Coal Basin and the results of analyses and evaluation of samples taken on restored localities Rado-vesice dump, Strimice dump, Ru?odol dum pand internal dump of Bilina mine. An example of modern non-tradicional restoration methods is the restoration of internal dump of Bilina mine (application of power plant stabilizer). According to observations and results of sample analyses the methods of restoration were selected to limit the erosion influence, adjust the chemical and physical composition of surface of Radovesice and Strimice dumps. The application of marlites and bentonite prevent the unfavourable weathering processes on dump surface. Compensation of Quaternary sediments was artifically formed here. The need of marlite ploughing in, application of organical substrates and vegetation preparation was proved on Radovesice dump. The conception of landscape reclamation of the largest dumps after finishing of mining, methodology of technical reclamation and well considered using of fertilizable soils are main results presented in this article.

Jan 1, 2014

By B. Q. Xiao

In surfactant flooding, surfactants added are often a mixture of the same type of molecules with different lengths of carbon chains. The relationship between a single, pure surfactant solution and crude oil is seldom studied. Additionally, up to now, alkylbenzene sulfonates are applied widely in surfactant flooding, such as Daqing oilfield, China. A factory producing alkylbenzene sulfonates will enlarge its yield to 20 000 tons per year over there. For the purposes of widening the alkylben-zene sulfonates? application, 16 kinds of pure alkylbenzene sulfonates were synthesized through Friedel-Crafts acylation and Wolff-Kishner reduction reactions, and the compounds? molecular structures were confirmed by 1HNMR and 13CNMR spectra. The factors affecting interfacial tension (IFT), such as, surfactant type, oil composition, electrolyte concentration, and alkali concentration were considered. The synthesized pure surfactants? critical micelle concentration (CMC) and optimal salinity were measured through interfacial tension technique. According to lab experiments results, heavy alkylbenzene sulfonate (2SY) was synthesized in magnifying scale in Jinzhou Wash Chemical Plant and the coretests were conducted using it. The results showed that the homemade heavy alkylbenzene sulfonate (2SY) flooding can improve oil displacement efficiency 20% more than water flooding at surfactant?s concentration from 0.05%(wt) to 0.2 %(wt).

Jan 1, 2014

By Robin J. Batterham

Alumina demand is steadily climbing around the world and is likely to continue to do so for many years. In such a commodity industry, the question arises as to what effort should be expended on innovation, given that for an individual company, the drivers of change are cost and quality as the market demand is essentially assured. This is of course a long-term view. The current conditions are less attractive. In this presentation, we review the broad issues that are considered targets for collaborative development by the industry as recently updated in the alumina industry roadmap published by the International Aluminium Institute in 2010. While they cover areas such as ?mine rehabilitation, residue management and use, alumina production from high sulfur bauxite, bauxite beneficiation, energy efficiency and alternative technologies for alkali and alumina recovery from bauxite residues,? it must be remembered that each refinery is different in terms of the feed material and the circumstances of waste disposal. Of particular interest is the more competitive area of breakthrough technologies. In the presentation, we will consider a range of opportunities that could transform the industry, from relatively near term possibilities such as bauxite activation through possibilities to eliminate crystallization as currently practiced to complete alternatives, such as the use of hyperaccumulating plants. Against this optimism, some of the realities that hold back breakthrough innovation will be presented for discussion.

Sep 1, 2012

By X. J. Lu

Purified Na-montmorillonite samples were used as the starting materials to prepare organically modified montmorillonites (OM), and a series of OM samples were prepared by intercalation of al-kyl quaternary ammoniums with different alkyl chain length. The interlayer spacing (d001) of the OM was determined by small angle X-ray diffraction and its gelating performance was characterized by measuring the viscosity of OM/dimethylbenzene mixture. The effects of alkyl chain length, dosage of alkyl ammonium, intercalation duration and layer charge of the starting material on the OM structure and gelating properties were investigated. According to the results, the adsorption quantity of the alkyl ammonium is dependent on the hydrocarbon chain length, the dosage of the alkyl ammonium and the retention time. The adsorption quantity of the alkyl ammonium increases with the chain length and the dosage, and extra adsorption more than the CEC of the montmorillonite sample was observed under the dosages of more than 1.3 CEC. The interlayer spacing (d001) of the OM shows a dynamic variation with the dosage and the retention time, and super interlayer spacings greater than the length of the alkyl ammonium were observed under larger dosages and shorter retention times. However, the gelating performance of OM does not follow the variations of the adsorption quantity of alkyl ammonium, an optimum viscosity value of OM/ dimethylbenzene gel was observed with the moderate adsorption of the alkyl ammoniums. Furthermore, the layer charge plays an important role on the gelating performance of OM. The OM synthesized by the starting material with lower layer charge shows better gelating performance in the dimethylbenzene solution.

Jan 1, 2014