Search Documents

By F. Q. Cheng

Despite the successful industrial practice to recovery KCl by flotation, the adsorption state of collectors at KCl salt surfaces is still not fully understood. In this paper, the captive bubble contact angle measurements at KCl and NaCl crystal surfaces in their saturated solutions are reported. The influence of different collectors and their concentration are considered. The results show that both cationic and anionic collectors produce a hydrophobic state at the structure breaking KCl salt sur-face, with finite contact angle values of between 30o and 40o. In contrast, the contact angle at the structure making NaCl salt surface is zero at all collector concentrations, suggesting that no collec-tor adsorption occurs, a supposition that is supported by results from molecular dynamics simulation (MDS). Further, it appears that the presence of surface defects such as edges and corners promote the adsorption of collectors at the KCl surface, and that the flotation is achieved by bubble attachment at the edges/corners of KCl particles with the formation of aeroflocs.

Jan 1, 2014

By Hossein Zarei, Masoud Kashani, Mehdi Safari

The feed of flotation unit in Angouran mine, as a part of Iranian Lead and Zinc National Corporation, contains about 34.26% zinc (about 12% Zn sulphide) and 10.14% lead (about 2% Pb sulphide). The grade of Pb and Zn in the final concentrate (rougher+scavenger), under optimal conditions (200 g/ton PEX, 500 g/ton zinc sulfate, 30 g/ton MIBC and pH = 7.5), was 63.18% and 13.01%, respectively, and the total Pb (sulphide-oxide) recovery was about 19% which included 95% Pb sulphide. The grade of Pb and Zn in rougher concentrate step was about 71.86% and 5.97%, respectively, when PEX (Potassium Ethyl Xanthate) was used as collector. While in the presence of PAX (Potassium Amyl Xanthate), the grade of Pb and Zn in rougher concentrate step was 66.8% and 10%, respectively. Tailing of the galena flotation (with 8.48% Pb grade and 34.92% Zn grade under the optimal conditions) was used as a feed for sphalerite and oxide section flotation.

Jan 1, 2014

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By M. D. Amirova

Cyanide-free technology of complex copper-lead ores flotation may be improved through enlarged range of pH values, enhanced copper recovery into copper concentrates due to additional recovery of secondary copper sulfides, as well as through enhanced efficiency of lead sulfides depression in process of new flotation modifiers-based selective separation. Study of the effects of flotation modifier (of metal nature) on minerals surface conditions proved that the xanthate is practically not adsorbed on the galenite surfaces due to minerals hydrophilization. Joint effects of sodium sulfite and modifier enhance process conditions for intensive galenite depression and at the same time for effective chalcopyrite and chalcosine flotation within a large pH values range (from pH=8 to pH=10). Identified mechanisms carry inference that proposed chemical reagent treating method is very promising for selective copper-lead concentrates separation. Potential use of carbon-containing materials as zinc flotation modifier to enhancing zinc recovery in processes of lead-zinc ores treatment has been studied. In our flotation tests we used Shalkiya (South Kazakhstan) lead-zinc ores containing such impurities as carbon shales, which presence impedes the process of saleable concentrates production and gives rise to excessive consumption of flotation agents due to the xanthate adsorption on the carbon. Lead and zinc concentrates were produced by process stages as follows: ores milled to 95% Cl. -0.074 +0; lead and zinc roughing flotation and further recleaner and testing operations. Test flotation in open process cycle resulted in enhancing zinc recovery into zinc concentrates by 21.1% and increasing zinc content in zinc concentrates by 3.96% that evidences promising potentialities for use of carbon-containing products as additional zinc flotation modifier. Works were carried out under National Program 2003~2005 of fundamental researches ?Physical and Chemical Mechanisms of Interactions in Multicomponent Solid and Liquid Systems Specific for Integrated Processing of Complex Metal-Containing Minerals and Technogenic Raw Materials? and contractual Agreement 2005 Optimization of Production and Technology of Shalkiya Lead-Zinc Ores Processing at Kentau Dressing Works.

Jan 1, 2014

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

By S. M. Narbekova, L. V. Semushkina, Zh. A. Aldybayeva, A. A. Mukhanova, D. K. Turysbekov, N. K. Tussupbayev

More complex and heavy-concentrating oxidized and mixed sulphidic oxidized ores are involved in production because of increasing needs for non-ferrous metals. Extraction of the oxidized minerals of non-ferrous metals general in current technologies. The problem is solved to oxidized polymetallic ores the preliminary selective sulphidization is the oxidized surface of the components by means of hydrogen sulphide, sulphide and calcium polysulphide, and also element sulphur, etc. The task was to study details of flotation of the oxidized lead-bearing ore of the Zarechnoe deposit (Kazakhstan) with calcium polysulphide as sulphidation. According to chemical analysis initial samples of the ore contain, %: lead – 4.8; zinc – 0.1; general iron – 0.81. Phase structure lead is characterized by the oxidized form of 57.76-64.5 %; by sulphidic status of 25.5-32.64 %, and by plyumboyarosite of 19.0-23.02 %. Researches on flotation beneficiation of oxidized lead-bearing ore are conducted. Sulfidizator gave to grinding, on flotations there were used the collector (butyl xanthogenate of sodium) and frother (T-80). Experiments were conducted with a new sulphidizator – calcium polysulphide. The latter is obtained by interaction of CaO calcium oxide with sulfur and water at high temperature with component mass the following ratio S:CaO:H2O =10:5:85. Extent of mill initial ore was optimised (88.42 % of - 0.071 mm grade). For the optimum mill mode the studies on matching of an optimized consumption of sulphidizators are performed. On basic technology with application of sulphide of sodium as a sulphidizator at optimum mill, the lead concentrate with the content of lead 64.4 % at extraction of 86.6 % was received. The content of cerussite in a concentrate was about 14.9 % at extraction of 82.1 %. With application of calcium polysulphide as a sulphidizator the lead concentrate with the content of lead 68.0 % at extraction of 88.0 % was received. The content of cerussite has made 16.0 % at extraction of 85.0 %. Application of a new sulphidizator allows to increase extraction of lead in a concentrate from 64.4% to 68% and cerussite extraction – from 82.1 % to 85.0 %. The possibility of application of calcium polysulphide as a sulphidizator instead of conventional sulphurous sodium was established.

Jan 1, 2018

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By Diana Drinkwater, Tim Napier-Munn

"This paper argues that, although specialist mineral engineering expertise is essential for the efficient design and operation of mineral processing plants, the environment in which these skills are supplied to the industry has changed forever, and not for the better. Most of the mineral engineering programmes in western universities have died or are dying. The long-service mine site mentors have gone, operations are run on a staffing shoestring so that there is no longer the time (or inclination) for considered decision-making, and the FIFO model has discouraged continuity of optimisation projects and communication between professionals. At the same time the technical challenges of designing and operating effective process plants are increasing. These trends are not going to be reversed any time soon, if ever. The ability to run efficient mineral processing operations has been materially compromised as a consequence. We propose that well-designed professional development can help to recover this situation, and it can be done easily and cheaply. The workplace is the best environment for such skills development. Professional development training should be integrated with normal duties throughout the early years of a graduate’s service (and probably beyond), and the cost should be regarded as non-discretionary expenditure for the business. If such programmes are properly resourced and managed and extended over longer time periods, there will be a measureable rise in the level of technical understanding and competence within companies and a resulting beneficial impact on resource utilisation and thus shareholder value. The paper outlines some of the approaches that we believe will work, and the benefits that we expect will accrue."

Jan 1, 2014

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By S. Titkov

At present, Russia is engaged in processing, 3new plants of hard-to-process potash ores with increased content (up to 10 - 12%) of insoluble impurities (insoluble residue ? I.R.). This required additional research to improve the process of potash ores flotation. Based on the study of the effect of dispersive properties of frother and its flow rate on the efficiency of aliphatic amines with different length of the hydrocarbon radical (as sylvite collector) there was showed the possibility to apply high molecular amine with length of hydrocarbon radical C20 ? C26 by normal temperature of circulated plant salt solution (saturated solution KCl ? NaCl ? H2O). There was designed and tested in plant conditions the modified amine collector with the length of the hydrocarbon radical C16 - C26, improving flotation of Sylvite under normal temperature of circulating salt solutions at potash flotation plants. There was made the study of the influence of the hydrocarbon radical length of alkylmorpholine on the Halite flotation from intermediate products of sylvite recleaner flotation with different content of I.R. (silicate-carbonate slimes), at normal and elevated temperature of salt solution. On the basis of the application of modified alkylmorpholine for Halite flotation, there was developed the process of further beneficiation for the intermediate products of sylvite recleaner flotation from potash ores with increased content of insoluble impurities, which can eliminate the circulation of the intermediate products in the process flow sheet of sylvinite ore processing and increase the KCl recovery into the finished product. Keywords: flotation, potash, halite, alkylamine, alkylmorpholine

Sep 1, 2012

By Chandra Sekhar Gahan

The present study aimed to investigate the depyritization of coal using iron oxidizing and sulphur oxidizing acidophilic chemolithotrophic microorganisms in an iron free 9K growth medium at varying pulp densities. Three different coal samples used in the shake flask study from three different countries such as domestic anthracite (Korean), Indonesian and Chinese lignite. Experiments were carried out in batch at a controlled temperature of 35 °C and varied pulp densities of 8%, 10% and 12% (w/v) with a working volume of 100 ml containing 10 ml of microbial inoculum and 90 ml of the iron free 9K growth medium. Coal samples were crushed and ground to fine size fractions <100 microns by attrition mill wet grinding. The progress in the experiments were followed by the regular measurements of pH, redox potential, viable planktonic cell count, residual Fe2+ ion concentration, amount of acid addition and amount of slaked lime addition. The pyritic sulfur removal percentage varied between 90-95% with highest sulfur removal with China coal (95%) followed by Korean Coal (93-94%) and slightly lower level for Indonesia coal (90%). However the pyrite oxidation was highest for Korean coal ranging between 78-80% followed by a similar level of pyrite oxidation of 50-61% for the Chinese and Indonesian coal. It was found that 10-12% pulp density would be fairly feasible for all the different coals tested leading to an economical process. Another benefit from this study is the iron free 9K growth medium, which will reduce the operation cost and overall it?s an environment friendly process.

Sep 1, 2012

By Xianjun Lu

This paper presents gold occurrence investigations on the altered rock gold deposit from Jiaodong area of China, and comparisons of gold occurrence in the ore samples from different mining levels. According to the results, the chemical and mineral compositions of raw materials from different mining levels are quite similar. However, the relative content and grain size of gold minerals are quite different between the two mining levels of -130m~-340m and -550m~-650m. In the ore of upper mining levels of -130m~-340m, electrum is the dominant gold mineral and accounts for about 80% of the total gold minerals, while native gold is minor and accounts for about 20%. As for the ore of deep mining levels of -550m~-650m, the major gold mineral shifts to native gold which accounts for 67%, while the ratio of electrum drops to about 33%. Coarser gold grain size was observed in the upper mining level ore with a mean size of 33.05µm while the gold grain size was much finer in the ore of deep mining levels with a mean size of 22.85µm. Furthermore, the gold mineral associations also show different patterns between the upper mining level samples and the deep mining level samples. Of the three observed gold association types such as inclusion gold, fissure gold and interparticle gold, more inclusion gold was found in the ore of deep mining levels. The inclusion gold accounts for 62% in the ore of deep mining levels, while that in the ore of upper mining levels accounts for about 56%. Further study revealed that the dominant gold associated minerals are pyrite and sulphides and only a small amount of gold is associated with quartz and silicates. It was shown that the altered rock gold ore from Jiaodong area can be regarded as a free milling gold ore, but the processing parameters should be optimized for the ores in different mining levels according to the different gold occurrence. In addition, it was predicted that enhanced gold liberation is necessary for the ore in deep mining levels.

Sep 1, 2012

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

By Z. Hu

A complex polymetallic sulfide ore in Yunnan, China, has various valuable minerals, which are Chalcopyrite, Galena, Pyrite, Gold, Silver, and Magnetite. A reasonable new flowsheet with a bulk flotation and a flotation separation of sulfide minerals that are Chalcopyrite, Galena, and Pyrite was carried out at first stage. After that tailings were treated by low intensity magnetic separation to achieve magnetite concentrate. A high Pb concentrate assaying 60.00 percent Pb at total recovery of 75.71 percent with 40.50 g/t Au and 1390.00 g/t Ag, a final high Cu concentrate assaying 24.45 percent Cu at high recovery of 92.03 percent and a magnetite concentrate assaying 60.78 percent Fe at recovery of 33.61 percent with 18.45g/t Au and 234.99 g/t Ag, are obtained. The total recovery of Gold and Silver in Pb concentrate and Cu concentrate reached 71.63 percent and 67.32 percent, respectively. It is shown, that this new flowsheet could realize efficient recovery for all of the valuable minerals in the ore and is easy to be industrialized. Keywords: bulk flotation, magnetic separation, polymetallic sulfide ore, depressant

Sep 1, 2012

By R. K. K. Mbaya

The concept of adsorption or separation of platinum anions from base metal cations in chloride media using native or chemically modified activated carbons has been discussed in various journals within the context of batchwise systems. In our research work, a fixed-bed column, loaded with native and amine-immobilized activated carbon pellets (Norit RO 0.8), was used to study selective adsorption of platinum ions from chloride media at different flow rates, bed depth and initial metal concentrations. The kinetics, mass transfer characteristics, breakthrough data and separation factors (ß(Pt/Fe) and ß(Pt/Cr)) were quantitatively analysed and modeled. The bed-depth service time (BDST) model was used to model the breakthrough curves successfully in fixed-bed columns and also the dispersive diffusion in the radial and axial directions of the bed were evaluated. The inner diameter of the column was 3 cm and the bed depth was between 1.0 cm and 2.5 cm. Concentrated 4 M HCl acid solution was used to elute the fixed-bed column. It was demonstrated that amine-treated activated carbons provides superior separation factors between platinum and base metals (Fe, Cr). Results showed also, that 95% saturation was reached within 10~26 hours depending on the nature of ACs at a flow rate of 11 mL/min and initial concentration of 5 ppm.

Jan 1, 2014

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012