Search Documents

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, T. Gurkova, T. Chumakova, Sylvinit Co.

"INTRODUCTIONFlotation of mineral particles by cationic surfactants – namely alkyl amines and their derivatives – is finding ever growing application in processing of various ores and in quality refinement of the benefication end products, iron concentrates for example. In the recent years application of cationic collectors - alkylmorpholines - enabled the development of new highly efficient procedure of water-soluble mineral processing, being also the one with low energy consumption. This procedure is a reverse flotation of carnallite from bay salts of salt-pans and from carnallite ores.The efficiency of cationic SAS influence depends upon colloid-chemical state of the collector in flotation liquid phase, especially if the latter comprises mineral salts. Availability of clayey impurities or slime particles of iron oxide in cation flotation feed, which actively sorb the cationic collector, deteriorate considerably the cation flotation performances. In Halurgy Institute the investigations of cation flotation under potash and carnallite ore processing have been carried out, and new reagent modes, enhancing cationic surfactants sorption at mineral particles, have been developed. Application of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles."

Jan 1, 2003

By lves Matiolo, Jorge Rubio, Carlos Perez Guerrero, Denise G. Nunes, Fabiano Capponi

The problem (very old) of processing by flotation, the fine (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral particles continues to be a major technical challenge in the area of mineral processing. Many different processes have been proposed over the last three decades but, unfortunately, most of them have not found practical applications yet. This paper describes some advances in flotation research in fines (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral recovery by two different techniques. Extender flotation (EF) and flotation with bubbles with a wide size distribution-SB of copper sulphide ore fines (1 % Cu) were compared with a “standardised” (STD) mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), “true” flotation recoveries and process kinetics. Copper porphyry samples, containing about 1/3 of the mass and about 37 % of the total copper content in the fines and ultrafines fractions were used. In the EF tests diesel-in-water emulsions were used as an extra reagent, added after the collector and frother addition. In SB tests, drawing air through an aspiration nozzle, directly in the pulp, generated bubbles sized about 50-200 µm. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physicochemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged. The following figure shows size-by-size copper recoveries results, after classification of produced concentrates and tailings using micro-sieves. Results clearly show that flotation of the F and UF fractions is highly improved with injection of small bubbles (SB) and with the addition of an extender collector. It is believed that the techniques presented here will establish shortly a new basis for the flotation enhancement of the F and UF, aimed at solving a very old problem. This work is being continued, now at pilot plant scale, and results will be published en the near future.

Jan 1, 2003

By Johan Nell, Paul den Hoed

"Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and hightitania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes.When large proportions (30 wt%) of carbon are added to the charge, then the reactionTiO2 + 2C + 2Cl2 = TiCl4 + 2COis favoured overTiO2 + C + 2Cl2 = TiCl4 + CO2Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites."

Jan 1, 2003

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By Juan Pablo Segovia, Alonso Pereira, Fernando Concha, Daniel Sbarbaro, Samuel Vergara

A robust theory of sedimentation-consolidation evolved and was accepted by researchers worldwide in the last two decades of the 20th century. This theory provides a reliable method of thickener design, simulation and control. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Although it is important for a mineral processing plant to perform periodical laboratory test to determine thickening parameters, and in this way adjust the operation, not always these tests represent the behavior of the material in the process. It is important to be able to determine these parameters directly in the thickeners. Research workers at the University of Concepción developed new instrumentation, algorithms and software for the determination of thickening parameters. In this paper, two new instruments for the on-line determination of the settling velocity and the compressibility of the sediment are presented and results of tests in a major mineral processing plant in Chile are described.

Jan 1, 2014

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work. • Effective Experimental ValidationAn automated 3D tracking technique is employed to study the motion of plastic particles deep within the charge of a 142mm diameter experimental mill. A Biplanar Angioscope is used to film the mill with X-rays in two planes simultaneously at 50 frames/s, with a shutter speed of 1/3000s. A marked ball within the charge is tracked for over 2 minutes and the resulting digital images processed by a fully automated imaging technique, which locates the 3D coordinates of the particles to within 0.2mm. With over 250 circulations, this provides statistically rigorous and accurate data for verification in the numerical modelling of mills.A series of validation techniques have been developed to compare the experimental trajectory data with the outputs of both 2D and 3D DEM simulations. The techniques describe the shape of the charge and the particle motion within mill, allowing objective comparisons to be made of key features of the charge, such as the equilibrium surface and the centre-of-circulation."

Jan 1, 2003

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By J. Yianatos

The cleaning circuit operation and its effect on the plant metallurgical performance, was characterized at Los Pelambres concentrator, Chile. Experimental data from columns, scavenger and regrinding stages was evaluated. Each stage was characterized by size fractions, and the interaction between stages (columns, scavenger, regrinding) as well as the effect that circulating loads had. The approach for describing the flotation equipment operation (cells and columns) considered the collection and froth zones separately. This methodology allows for the identification of the impact that particle size distribution has on the actual collection and froth transport processes, independently. In this way the effect of regrinding on flotation recovery and grade can be related to the corresponding operating variables, e.g. pulp flowrate, air flowrate, pulp level and pulp density, among others. The effect of gangue entrainment was considered using an empirical dimensionless correlation. The interaction between the circulating load and the overall performance of cleaning circuit was evaluated. The circulating load was defined as the ratio between the solid flowrate of scavenger concentrate over rougher concentrate. It was found that the overall cleaning flotation circuit (column-scavenger) can operate at a relatively high and constant recovery for a wide range of mineral treatment. This is possible when the scavenger has the capacity for compensating the decrease in column recovery at larger circulating loads. Under the condition of high overall cleaning recovery, the rougher stage closely represents the plant recovery. However, at large mineral treatment conditions, the design characteristics (e.g. concentrate transport channel capacity and transfer boxes) as well as instrumentation, control facilities and operation, became bottle-necked. A simulator was developed using empirical models for each stage (column, scavenger and regrinding) in order to evaluate proper operational strategies for cleaning flotation circuits Keywords: flotation, cleaning, regrinding, Vertimill, simulation.

Sep 1, 2012

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Weiguo Xie, Malcolm Powell, Lian Liu, Ping Yu

"In order to develop a common mathematical and simulation platform for tumbling mills, a review of existing mechanistic models was made identifying the key aspects of grinding and slurry transport which are common to all tumbling mills. A mill model structure has been developed for all types of tumbling mills based on the population balance framework by incorporating breakage characteristics, slurry and solids transport, product classification and discharge, and energy consumption. A size-dependant breakage model developed by the JKMRC is applied. Transport is separated from breakage events and treated as a main sub-model in the new model structure. The model structure is based on dynamic time-stepping technique to enable dynamic simulation capability for non-steady-state simulation and control modelling. It is envisaged that the new model will cover a full range of milling conditions. It should enable a smooth transition between different mill types, such as from AG (Autogenous Grinding) to SAG to ball mill. The dynamic mill model structure developed here is the first step towards mechanistic modelling of grinding mills and provides great potential for the optimization of the comminution process."

Jan 1, 2014

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By P. Huang

Chitosan was tested as a depressant in the differential flotation separation of chalcopyrite and galena. The micro-flotation results showed that chitosan selectively depressed chalcopyrite while galena was floated by potassium ethyl xanthate in acidic solutions. With the addition of 0.67 mg/L chitosan (CT) in the slurry of chalcopyrite-galena mixtures at pH 4, the recovery of galena was 95% while that of chalcopyrite was 30%, indicating that chitosan could potentially be used in differential Cu-Pb sulfide separation. Furthermore, the study of chitosan with either low (LCT) or high molecular weight (HCT) in the differential flotation indicated that better separation was achieved by the chitosan with lower molecular weight (LCT). ToF-SIMS was employed to study the distribution of CT on the surface of chalcopyrite-galena mixtures by ion mass spectra analysis and surface imaging, which showed that CT adsorbed heavily on chalcopyrite but barely adsorbed on galena. The positive ion ToF-SIMS spectra provided information on the surface composition of chalcopyrite-galena mixtures after CT treatment. It appears that the selective adsorption of CT on chalcopyrite was originated from the strong interaction between NH3+ and Cu. Keywords: differential flotation, micro-flotation

Sep 1, 2012

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By O. A. Punishko, G. G. Mineev, Zabaikalsky Ore-Dressing Plant, M. V. Malova, O. V. Belousova, S. A. Bogidaev

"In order to intensify benefication processes (flotation and magnetic separation) for rebellious tantalitecolumbite ores electrochemical machining of pulp (ECM) is suggested instead of costly mechanic-chemical activation and magnetizing roasting. Any change in the surface mineral-semiconductor potential under the action of electrochemical treatment results in the change in the isoelectrical state of the surface and the adsorption property of the mineral with respect to ionogenic reagents-collectors. In this case conditions are created for regulating the ion composition, reduction-oxidation potential and pH of the liquid phase of the pulp without any extra introduction of expensive and often ecologically harmful chemical substances.Ores containing tantalum and niobium are characterized by complex chemical composition, determining their physical properties (conductivity, dielectric penetration, magnetization value, etc.) and their electric susceptibility.The authors investigations show that the pulp electrochemical treatment leads to the increasing magnetic susceptibility of the paramagnetic minerals. The main chemical elements forming the columbite-tantalite minerals except tantalum and niobium are iron and manganese. They determine the rare-metal minerals paramagnets properties. The electrochemical treatment changes the relation of the oxidized and reduced forms of these elements having. The method of cathode pulp treatment before flotation is successfully tested industrially.In the field of noble metals metallurgy new technological proposals are reduced to the following. As is know, the production of noble metals from unusual raw materials demands the elaboration of principally new technologies new technologies in so far as the methods for gold and silver extraction from ores are as a rule low elective and at the existing level of engineering are economically not expedient.The analysis of the main trends in the field of non-standard raw material treatment shows that the perspective ones are the geo- and biotechnological processes (underground leaching and leaching in heaps - UL and HL and microbiological methods of metal extraction)."

Jan 1, 2003

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012