Search Documents

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By P. Somasundaran

While sustainability itself needs to be redefined in a selfless way, methods of measuring and optimizing it also need to be reformulated. Gone are the days when we had the luxury of abundant resources and the freedom to extract values in self-centered ways. In the past, focus has been mostly on reagent performance, processing operations, and upgrading of tools to maximize rather than optimize value extraction from the earth's crust. Today we as extractors face a new set of challenges that include value separation from low quality resources including wastes, but within the energy, environment, and societal constraints. Development of such technology depends on understanding the role of entities and concepts such as bio-molecular interactions at surfaces, forces involved in inter-granular versus intra-granular fracture in new fragmentation methods, robotic in-situ or extraterrestrial mining, exploiting new membrane and nano technology, use of new sensors and actuators for detection and separation and computation capabilities for faster and economical processing. Equally importantly, we need to communicate with everyone what we foresee and anticipate when we extrapolate the type-performance-cost relationship of ores to the era ahead of us and establish viable schemes for ecological survival. Keywords: sustainable mineral extraction

Sep 1, 2012

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Y. C. Liu

Ningxiang-type iron deposit is a most important sedimentary oolitic hematite deposit in China. Its? detected ore reserves are 3.72 billion tons, which is 73.5% of all detected reserves, and there are about 10 billion tons of prognostic resources. It is considered as the ?poor mine? for a long time be-cause of its difficult prooerty. But based on the ore characteristics of different deposits, the technological characteristics of ore are different with great diversity in ore baring horizon, distribution range, deposit scale, ore petrology, ore mineral assemblage and iron content. Through the study of deposit features and technological mineralogy of different Ningxiang-type of iron deposits in China, and based on industrial types and natural types of ore deposits, we divide different technological types according the technological features of the ore such as mineral composition, particle size, dissemination, occurrence of useful elements and harmful elements, the main physical and chemical properties of mineral and geological conditions of deposits, etc, moreover, propose the different utilization, mineral processing technologies and product schemes for the different types of ore.

Jan 1, 2014

By Marzio Piller, Girolamo Belardi, Jure Mencinger, Paolo Bozano, Gianni Schena

"The hydrodynamics of the Tri-Flo™, a two stage cylindrical cyclone used in dense media separation, is studied using Computational Fluid Dynamics. The flow field is simulated with an Euler-Euler Volume of Fluid two-phase approach and the Reynolds stress turbulence model.A unique feature of the device is that the separation medium suspension is pumped and introduced tangentially into the two cylindrical compartments while the raw feed is conveyed to the feed hopper and fed at the axial inlet. This feature allows to use less pumping energy and limits the unavoidable production of fines. The Tri-Flo™ complex flow pattern is little known but central to the efficiency of the separation.The velocity field is computed within the two compartments of the separator. The interface of the air-core that forms in the inner axial part of the cylindrical sections is identified and visualized. The numerical results for a reduced-size 100 mm ID Tri-Flo™ are compared against laser Doppler measurements on a transparent acrylic model (Chinè, 1995) operated with water. The robustness of the model and its prediction capability are verified.The possibility to accurately predict the velocity profiles within the vessel and their dependence on the main Tri-Flo™ operating and geometrical variables paves the way to a better understanding of the functioning of the separator, its design improvements and scale-up."

Jan 1, 2014

By G. Y. Zhou

During Zijinshan copper heap bioleaching, pyrite was leached in plenty resulting in high ferric concentration in solution. It has affected bioleaching and extraction processing greatly. It results much acid and iron in solution and bad effect to extraction processing. The paper studied the influence factors in the course of pyrite leaching and ferric ion chemical oxidation, especially studied the redox potential for copper bioleaching so as to find key factors affecting the dissolution difference between chalcocite and pyrite. The results show that the redox potential is important factor. Copper and pyrite leaching rates are 95% and 11% respectively and there is great dissolution difference between them at redox potential 700 mV (SHE). During pyrite bioleaching, the indirect action of bacteria gives priority to bioleaching cooperating with the direct attack of microbial cells attached to the mineral surface. Redox potential is determined by ratio of ferric and ferrous, ferric in solution was supplied by the way of oxidation of T. f bacteria, sufficient bacteria concentration and active character were two vial factors of controlling redox potential. It is indicated that copper can be selectively bioleached during copper bioleaching by controlling redox potential of bioleaching. The conclusion will provide theoretic foundation on balance of acid and iron during bioleaching for copper of higher S/Cu ratio. The experinment proved that bacteria activation was decreased on condition of both low pH value and intermittent aeratation during bioleaching. It resulted that the oxidation velocity of ferrous ion was decreased and redox potential was controlled. The dissolution of pyrite was depressed. It would be possible to actualize selective leaching of secondary sulfide copper ore during bioleaching process.

Jan 1, 2014

By G. S. Zeng

The mechanism of cobalt removal from zinc sulfate solution with zinc dust is still not understood well. The experiments in this paper were carried out by zinc dust from zinc sulfate solution with high cobalt to study the mechanism of cobalt removal. Residues after the cementation process from zinc sulfate solution were analyzed by SEM and Electron probe micro-analysis (EPMA) to investigate the morphology of products. Different temperature will cause different structure of particles. With the increasement of temperature, cobalt removal can be improved considerably. The mechanism of cobalt removal by zinc dust is thought as follows: firstly, the cobalt ion forms Co-Zn alloy with zinc particles, and the reaction reaches equilibrium quickly; secondly, the Co-Zn alloy continues reacting to Co with Co2+, which is the control procedure of the whole reaction.

Jan 1, 2014

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By V. Avdochin

The main reason of flotation process fluctuations is mixing ores of various properties from various sections of a deposit. Other, also important reasons are changes in parameters of facilities of technological cycle, as well as properties of reagents applied. According to estimates, instability and non-optimized parameters of flotation owe 3% to 6% of valuable component losses. Without ore averaging systems flotation process is characterized by considerable fluctuations of all input, output and intermediate parameters. Stab One more way is optimizing the process, providing for determination and maintaining optimal parameters of the process. In these conditions application of various mathematic models does not allow controlling the process by the way of action on input parameters of the process with further precise reaching required values of output parameters. More effective is to be application of flotation models for solution of questions of choosing and optimizing of automatic control systems. The work presented examples of application mathematic model of flotation process for estimation of effectiveness and choice of parameters of automatic control system that reduces considerably a stage of preliminary studies in elaboration, designing and modernizing automatic control systems.

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By Ray Everson, Henry Kasaini

"Adsorption of Pd (II) anions on the surface of activated carbon (Norit 0.8) occurred at high proton concentration (0.01 – 2.5M, HCl) in the feed and averaged 27 mg/g. The adsorption process was interpreted in terms of surface ionisation and adsorption model. Enthalpy of adsorption averaged 0.4 kJ/mole indicative of an instantaneous physical adsorption process. We found that the Toth isotherm fit the adsorption data fairly accurately. A combination of the Langmuir and Freundlich equations yields an effective three-parameter Toth equation (1) which is frequently used to describe adsorption on heterogeneous surfaces.Figure 1 shows the comparison between experimental results and the model isotherms. We found that Langmuir isotherms underestimated the adsorption capacity on the porous surface while the Freundlich isotherm overestimated adsorption. Furthermore, the surface coverage at equilibrium was well described by both the Langmuir and Toth isotherms. But, Freundlich isotherm predicted a surface fraction coverage that was higher than unit. Based on better prediction of surface coverage and a reasonable fit to adsorption data, we concluded that the Toth isotherm best described the adsorption data of palladium. The adsorption process was limited by mass transfer resistance through the external film. We estimated the rate constant from equation (2), where e, ?b, and rp are porosity, fluid density and particle radius, respectively"

Jan 1, 2003

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By K. V. Fedotov, E. V. Zelinskaya, O. V. Ulanova

"Mining enterprises, in particular, those on the territory of the Siberian platform, produce large amounts of pumped water, which cannot be recycled because of its high mineralization and, thus, is discharged as liquid waste either back into the ground or onto the surface. However, groundwater is often a valuable raw material and a source of useful chemical substances. Brines are unique groundwaters. In the current environmental and economic situation, the huge loss of natural raw materials and their deliberate conversion into wastes is unaffordable. The exploration of non-traditional sources of minerals such as the hydromineral resources (including pit water) is a matter of rational nature management. The industrial value of brines of the Siberian platform is due to the high contents of rare alkali and earth alkaline elements (lithium, rubidium, cesium, strontium, bromine, etc.). The absolute concentrations of these elements in brines are tens of times higher than the lower limits of the mining cut-off. The long-term data analysis was performed to estimate the environmental impact of liquid waste from two mining enterprises, namely, Korshunovskii (Irkutsk region) and Udachnaya (Southern Yakutia). The study was focused on the prospects of hydromineral resources as non-traditional sources of valuable elements and the exploration of technological processes for the selective extraction of rare alkali and earth alkaline metals from natural multi-component brines aimed at decreasing their negative environmental impact. The environmental and economic efficiency was proved for the processing of complex brines and the integrated selective extraction of rare earth metals from sodium chloride brines of the Korshunovskii plant and calcium chloride brines of the Udachnaya plant based on the ion exchange sorption, eluent chromatography, flotation, crystallization, and freezing techniques. The basic technological schemes were developed for the metal extraction from pit water and brines.INTRODUCTION In the Irkutsk region (the Angara–Lena artesian basin) and in Yakutia (the Olenek and Tunguska artesian basins), several mineral deposits are developed and, incidentally, aquifers bearing brines of different types are opened, which are eventually converted into liquid production waste (Rusetskaya et al., 1994) This raises the issue of the burial or utilization of brines since their use within the water circulation is impracticable under the existing technological conditions while their discharge into the surface watercourse is unacceptable because of the harmful environmental impact."

Jan 1, 2018

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014