Search Documents

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By Richard Pizzi

Built in 1806, Boston's African Meeting House is the oldest surviving Black church building in the country. A $7 million dollar renovation was begun in 2006 to restore this historic building to its 1855 appearance and to modernize the building's accessibility, electrical and mechanical systems. As part of the restoration, an underground utility room and elevator tower, needed to provide handicap access to the Meeting House, were constructed. Extending up to 17 feet below the foundations of the abutting buildings, the utility room was constructed within one foot of some of Boston's oldest and most expensive residences. All equipment and materials had to enter the work area through a narrow alley rendering conventional methods of excavation and construction of earth support using heavy equipment unfeasible. A unique combination of micropiles, structural cap beam, internal struts and shotcrete facing was designed and constructed to provide the permanent and temporary support of the lateral loads from the earth pressures and adjacent building surcharges and the vertical loads from the elevator tower. The narrow and congested streets of the Beacon Hill neighborhood presented many day-to-day challenges for the contractor.

Jan 1, 2011

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By Paolo Heiniger

The aim of this paper is to present the operative solutions devised and then adopted to implement the underexcavation (soil extraction) of the Tower of Pisa, by means of soil extraction. The intervention has been performed by the Consorzio Progetto Torre di Pisa, a joint venture made of five qualified Italian companies (Trevi S.p.A. , Rodio S.p.A., Italsonda S.p.A., Ismes -Enel Hydro S.p.A., Bonifica S.p.A.), selected for their experience in the field of monitoring and restoration of monuments, structural design, foundation engineering and specialised works in underground conditions. Since 1991 the Consorzio has been charged with the specific task of implementing, within the contractual frame of a Concession, all the decisions made by the International Multidisciplinary Commission appointed by the Italian Government the previous year, with the aim at solving the «problem» of the Tower, strengthening the structure and stabilising its foundation. The Trevi Group, which is represented by Trevi S.p.A. in the above mentioned Consorzio, has given and is giving its direct and constant contribution and is engaged in supplying the special equipment to the operation and the drilling technology which has been successfully adopted to date.

Jan 1, 2000

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By K. Rainer Massarsch

The effects of soil displacement caused by pile driving on adjacent piles and structures are discussed. A method is proposed to estimate the point of force equilibrium which makes it possible to calculate up-lift forces and pile head movements. For the case of pre-coring a method is proposed to estimate the stability of the bore hole, based on cavity expansion theory. Model tests were performed to establish the displacement pattern of the soil during the driving of a pile group. It can be concluded that at the ground surface, already installed piles have little influence on the lateral displacements, but reduce significantly the soil heave. During the driving of a pile group, the soil is displaced according to a complicated pattern, which is strongly influenced by the order in which the piles are driven. In clay the displaced soil volume corresponds to the total volume of driven piles.

Jan 1, 1989

By Loring A. Wyllie

Preparation, understanding and use of soils reports must be a team effort to be fully effective. The soils engineer must know what is to be built and exactly where. The structural engineer and owner must be fully informed on the foundation problems of the site. There must be frequent team review of information obtained from subsurface investigation and of design as details develop. The soils engineer should be available on a continuing team basis as design proceeds and should be directly involved with inspection and interpretation of site conditions as construction continues.

Jan 1, 1986

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014