Search Documents

By John Porritt, Alain Dorval

"TioMin Resources Inc. is evaluating the feasibility of exploiting the heavy mineral sands deposit at Natashquan on the north shore of the Gulf of St-Lawrence, Quebec. TioMin holds the exploration rights to 180 square kilometres, on which 1.6 billion tonnes of sands grading approximately 6% heavy minerals were outlined. The heavy minerals of value include magnetite, ilmenite/hematite, garnet, and zircon. An important part of this evaluation is the development and testing of a mineral separation flowsheet. Under a comprehensive mandate from TioMin, the Centre de recherches minerales (CRM) provided technical assistance to build and operate an on site primary concentrator pilot plant. This plant produced a 93 tonne concentrate, providing over 60 % heavy minerals. This concentrate was shipped to the CRM pilot plant in Quebec City. It was used for further flowsheet testing and for preparation of products and concentrates of heavy minerals with regard to marketing possibilities. This paper presents the flowsheet developed to produce these concentrates.IntroductionIn late 1992, an 11 tonne bulk sample of sand was collected from within the mineralized zone of the Natashquan deposit. This sample was processed over conventional spirals and wet tables at the pilot plant facilities of the Centre de recherches minerales (CRM) in Quebec City. A primary concentrate was produced, from which several 20 kg samples were forwarded to five research laboratories in North America and in Australia. Their tasks were to determine the mineralogical composition of this concentrate and the potential for recovery of marketable minerals from the heavy mineral sands. Satisfactory results obtained from this approach encouraged TioMin to proceed with a more detailed pilot plant program."

Jan 1, 1995

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By G. Zeng

Although the solubility of oxygen in zinc electrolyte is less than 9 mg/L, the effect on deposit stability and zinc-dust consumption can be significant. Sodium sulfite is used to deoxygenate the electrolyte. The effect of the sodium-sulfite concentration on cobalt removal is investigated. The results show the reduction of sulfite to elemental sulfur that adhered to the zinc dust surface forming a passivating layer, and small amounts of sodium sulfite have no effect on cobalt removal. The optimum amount of sodium sulfite is 100 mg/L. It is an important consideration in purification circuits to use sodium sulfite as an additive to cobalt cementation.

Jan 1, 2005

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By Jianhong Xu, Hailong Hou, Yu Jing, Yundong Wang

Microcapsules containing extractants have been applied to the extraction of metal ions, organic acid, pesticide, and herbicide. The difficulties of conventional liquid-liquid extraction in phase mixing and phase separation (e.g. high energy consumption, emulsification phenomenon, and large equipment requiring housing) could be overcome in a liquid-solid system by using microcapsules. Even some extractants with high viscosity and poison can be encapsulated conveniently into microcapsules. In the work described in this paper, polysulfone microcapsules containing 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (P507) were successfully prepared. Then, the extraction rate of lanthanum, samarium, and erbium in dilute solution into the microcapsules containing P507 was studied. An extraction kinetic model is proposed based on the interfacial reaction model accompanied by intraparticle diffusion expressed by Fick’s law. The extraction efficiency was obtained by using the kinetic model with the separately determined complex formation rate constant and the intraparticle diffusion coefficient. From the results, it was confirmed that the kinetic model could predict the experiment in a microcapsule system over a wide concentration range of lanthanide solution. In the future, the model could provide good guidance for the design and application in extraction of lanthanides.

Jan 1, 2014

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By Michael Bowker

Au/TiO2 catalysts were prepared by incipient wetness impregnation and tested for the room temperature photocatalytic reforming of methanol in aqueous solution. These catalysts proved to be more active, on a molar basis, than Pd/TiO2. The dependence on loading of gold was different from that of palladium, showing a double maximum in yield at 0.1 and 2 wt. % with low rate below 0.01% and above 10%. A model is proposed for the reaction involving band gap excitation of titania electrons which are used to oxidise the methanol via adsorbed CO. With palladium, photoreforming of CO and water can be achieved, but this is much less effective on gold, presumably due to the much weaker bonding of CO on Au.

Oct 1, 2003

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By Y. Sugiyama, K. Kitazono, T. Miura, K. Matsuo

"Impact energy absorbing system for automotive is an important technology. Open-cell porous aluminum alloys were manufactured through Powder Bed Fusion (PBF) process. Compressive properties of the porous aluminum alloy depend on the cell structure as well as the porosity. The authors manufactured two ordered cell structures, truncated octahedron and rhombic dodecahedron, and one disordered cell structure, random Voronoi structure using a 3D-CAD software. Compression tests revealed the anisotropic deformation of the porous aluminum alloy with ordered cell structure. On the other hand, the porous aluminum alloy with disordered cell structure showed relatively isotropic and uniform deformation, which is suitable for energy absorbing applications. Therefore, controlling the disordered cell structure designed by Voronoi diagram enables to develop the advanced porous aluminum alloy having various mechanical properties.INTRODUCTIONAdditive manufacturing (AM) process enables to manufacture near net-shape mechanical parts. The AM technology is typically focused on titanium alloys due to their high specific strength and biocompatibility (Attar, 2014). Recently, aluminum alloy parts can be manufactured through selective laser melting method (Leary, 2016). Metal foams or porous metals are lightweight cellular materials having closed-or open-cell structures (Banhart, 2001). Aluminum foams are focused on as an energy absorbing material for transport industries (Baumeister, 1997). The purpose of the present study is to investigate the optimal cell structure of open-cell porous aluminum alloy manufactured through AM process. Most previous researches on the AM aluminum lattice structure has been considered ordered and periodic cell structures. On the other hand, classical aluminum foams manufactured through cast or powder metallurgical processes have disordered and heterogeneous cell structures (Körner, 2000). The authors use a concept of Voronoi diagram (Moukarzel, 1993) in order to manufacture various cell structures."

Jan 1, 2018

By D. Adiguzel

In this research, providing the sustainability of production quality was aimed for a quarry which is located in Istanbul western part of Turkey and producing concrete aggregates with different types of rock. First, research field was divided in 3 different areas in accordance with the geological differences and parameters that control their product quality, limit values of standards and effect levels were determined. Concrete aggregate conformity tests which are stated in international standards were applied on samples which were taken from these 3 different areas and physical, geometric and chemical properties of each rock type were revealed. The properties of the 3 different types of rock which were produced in the quary were determined and the binary blends were composed. Blending studies were conducted with linear programming technique. In the linear programming model, the cost of aggregate production was aimed to be minimal. The limit values that meet literature and national standards for usability of aggregates in concrete were defined as constraints in the linear programming model and evaluated with objective functions, thus the most suitable aggregate blends were composed. In conclusion, to provide the sustainability of product quality, the most appropriate product blends were composed for the research field and the usability of this model for those quarries were revealed.

Aug 1, 2013

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006