Search Documents

By H. Clare Horwood

"Three types of structures, the main shear zone, the north shear zone, and a series of hanging-wall fractures, contain all the orebodies so far discovered at the McKenzie Red Lake mine. Lenses and veins of quartz in these zones and fractures are the sources of the ore. The ore-bearing structures are unusual in that they are in a complex intrusive mass known as the McKenzie-Gold Eagle stock. They are believed to have been produced by compressive stresses from the south andsouthwest.The mine is on the northeast side of McKenzie island, in Dome township in the central part of the Red Lake area. The original discovery, the main shear zone, was made in 1928, about 3 years after the property was staked, by M. L. Bouzan who was in charge of prospecting and development work on the property. Subsequent diamond drilling and underground exploration led to the installation of a mill, which came into production early in 1935. The hanging-wall fractures were found branching out from the main shear zone during development work on the 350-foot level. The north shear zone was discovered in 1940.From 1935 when the mill began operation until the end of 1946 total production from the mine was approximately 269,349 oz. gold and 69,317 oz. silver, having a value of $9,679,739, recovered from 823,527 tons of ore.GENERAL GEOLOGYThe McKenzie-Gold Eagle stock has a total length of approximately 1 ½ miles and a width of about ½ mile. It was intruded into a complex synclinal fold in Timiskaming sediments. The sediments, which have been cut in only one place in the underground workings, are principally wellbedded greywackes. The stock is composed of large masses of diorite and granodiorite, a small mass of hornblende pyroxenite, and basic dykes of two ages. The diorite occurs as irregular masses in large measure surrounded by the granodiorite that it intrudes. It contains tabular crystals of andesine, having a maximum length of3/4 inch. The hornblende pyroxenite is an elongated lens or dyke in the diorite. The granodiorite masses occupy about two-thirds of the stock. Along its eastern side the main mass tends to become darker and more dioritic toward the diorite contact.Basic dykes of pre-vein and post-vein age are the youngest intrusive rocks at the mine."

Jan 1, 1954

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979

By H. H. Wober, P. J. Morgan

"The proposed classification of ore reserves based on geostatistical and economic parameters is designed to be used as a communication tool to identify for investors, bankers, and financial analysts the degree of risk associated with a specific class of ore reserves. The class designation identifies the degree of accuracy of the estimates for tonnage and grade of annual production volumes of ore. It thus enables decision makers to quantify the risks and uncertainties inherent to the ore reserve in achieving over-all economic goals and annual financial objectives.IntroductionDuring the evaluation, in 1980, of the Creede silver deposit in Colorado, U.S.A., as a potential bulk mining project, the authors were faced with the problem of conveying to senior management the risks and uncertainties that are implied by using common or conventional classification systems to categorize ""ore reserves"". The estimated numbers for tonnages and grade of the projected ore reserves represented the only entry for future revenue from the project. It was, therefore, necessary to convey to management the level of risk associated with those numbers when implementing further stages of development, and to convey what impact significant differences would have on the profitability of the project. The desire to quantify these risks led to a revised definition of ""ore"" and to a re-examination of the classification system of ""ore reserves"". Traditional methods for estimating tonnage and grade of reserves do not include a quantification of the errors of these estimates. The advent of geostatistical methods made this quantification possible. The proper application of geostatistical methods, with adequate geological input and a reliable set of sample data, is essential to its validity.Others have proposed a classification of ore reserves based on geostatistical parameters. Diehl and David (1982) recognized ""that concepts of proven, probable and possible have to be linked to the production rate or time horizon"". Royle (1977) had also addressed this problem. Forsyth (1987) pointed out that bankers are concerned with ""the probability that the variability will fall within a certain degree of accuracy"" especially for grade estimates, and would like to see grades expressed together with the error of the estimate at the 950Jo confidence level."

Jan 1, 1993

By P. E. Weidmark

Allard, M., Hucka, V.J., Das, B., and Borchtch-Komponietz, V.I., "Investigation of seismic vibration due to large blasts in Gaspe Copper Mines"; (in Russ); The Industry of Chemical Raw Materials; Referativnyi sbornik; 5:18-20: 1978. Askew, J., McCarthy, P.L. , and Fitzgerald, D.J ., "Backfill research for pillar extraction at ZC/NBHC"; Mining with Backfill; Proc 12th Cdn Rock Mech Symp; May 23-25, 1978; Sudbury; CIM Spec Vol 19:100-lJO; 1978. Barrett, J.R., Coulthard, M.A., and Dight, P.M., "Determination of fill stability" ; Mining with Backfill; Proc 12th Cdn Rock Symp; May 23-25, 1978; Sudbury; CIM Spec Vol 19:85-91; 1978.

Jan 1, 1979

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By Michael S. Moats, Shijie Wang, Timothy Robinson

In 1987, John Schloen published a survey and analysis of copper electrorefining tank room data. Following this paper, a series of copper electrorefining surveys have been conducted and presented at each of the Copper-Cobre meetings over the past 20+ years (1991, 1995, 1999, 2003, 2007, 2010 and 2013). For each of these surveys, William Davenport has been key driving force in the collection and analysis of data. To honour Professor Davenport’s contribution to copper processing, a review of the data was conducted. Historic trends and possible future technologies are discussed.

Jan 1, 2014

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By Liangtian Liu, Tie Ou, Guangqiang Li, Chenghuan Yu

For stabilizing the production of containing nitrogen steels, a study on nitrogen absorption behavior of killed molten steel has been carried out by means of the RH vacuum device in which nitrogen was used as a driving gas. The results showed that there was an increase of nitrogen content in molten steel under vacuum processing but the rate of nitrogen absorption was slowed down by the surface active elements. Therefore, a kinetic equation for nitrogen absorption of molten steel with apparent first order reaction was derived by constructing a modified model in which the adsorption of closed surface site was taken into account. The experimental results confiimed that the calculated values agreed with the observed ones. This model is suitable for the prediction of nitrogen adsorption operation for containing nitrogen steels.

Jan 1, 2004

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By D. T. Aikens, R. Gaudreault

"This paper summarizes structural repairs carried out on a marine wharf consisting of six 13.7 m by 13.7 m reinforced concrete cribs linked together by five 14.6 m long beam spans. As a result of problems during original construction and twenty years exposure to severe weather conditions, the deck support system between the cribs required major restoration work. In particular, some of the beam seats under the crane rail supports had marginal bearing area to support the structural loads. Faced with closure order for the wharf which is required to bring in raw materials to the plant and a long outage to make repairs as stipulated by Ports Canada (owners of the structure) alternate means of making the required repair were examined.The method chosen allowed the work to be done much more quickly, at lower cost, without taking the wharf completely out of service. The badly deteriorated seats were rebuilt using epoxy grout, tapered sole plates and a positioning jig."

Jan 1, 1988

Orebody classification systems ? Modern classification systems ? Genesis and environment of deposition (Important in economic geology) ? Shape and structure / Form, texture and mineral content ? Mining and geomechanics ? Size ? Massive versus tabular Requirements for mining method selection ? Classification of ore deposit ? Shape, size, attitude, continuity ? Grade and distribution, strength and large scale structures present, mineralogy and small scale structure, host rocks ? Classification of mining method ? Method of support (Stress ? strength ratio) ? The method selection ? Geographical and economic factors of the location

Feb 1, 2008

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

By R. Carpenter, H. Muntanion, P. Kleespies, E. Flood, M. Tansey

Abstract - BHP Minerals discovered the Archean lode gold ULU deposit on the western margin of the High Lake Volcanic Belt in 1989. The greenschist to amphibolite facies mafic volcanic and sedimentary rocks on the property are folded into a 5 km-long anticline. There is a close spatial association of Au-As zones to the trace of this F2 ULU anticline. The largest of these auriferous zones, the Flood zone, is localized at the core of the fold. The southeast-trending Flood zone consists of several anastomosing lenses that have been traced for 435 m on surface. Overall, it dips steeply (70° to 80°) to the southwest and has been intersected to depths below 600 m. The hosting high-iron tholeitic basalt displays a lower amphibolite mineral assemblage of ferrohornblende + plagioclase + ilmenite with accessory quartz and epidote. Alteration minerals include biotite, chlorite, hornblende, actinolite-tremolite, and potassium feldspar (microcline) with minor calcite, epidote, tourmaline, and titanite. The highest gold values occur where brecciated basaltic wall-rock clasts are replaced by acicular arsenopyrite + quartz + K-feldspar. BHP Minerals completed 54,783 m of both exploration and resource development drilling before selling the ULU property to Echo Bay Mines in 1995. Development of ULU as a satellite deposit to Echo Bay’s Lupin mine began in 1996. A -15% ramp was extended to the 155-meter level, and 16,011 m of underground drilling were completed before the decline in gold prices forced a suspension of activities at ULU in August 1997. The current owners, Wolfden Resources Inc., drilled 18,569 m in 2004 to increase confidence in the resource blocks. Following this drill program, a revised resource calculated by an independent consultant determined that the ULU deposit contains an inferred/indicated mineral resource of 1,130,000 t grading 11.34 g/t gold (373,748 oz) to the 360-m level. The portal was re-opened in 2005 and a prefeasibility study is underway.

Jan 1, 2004

By Masaharu Moteki

At present, the Unmanned Construction System (UCS) is adapted on initial operation against the disaster. For instance, it has been used in Unzen. When the scale of the disaster is big, or the danger to a person is big, the UCS is expected as a quick and safe construction technology. The Remote Controlled UCS is introduced into construction site to repair earth-fill embankment or to remove rock, as urgent measures after the disaster outbreak. For improvement of the operability, shortening of the skill time, reduction of the fatigue, examination of the most suitable system (placement of a monitor and the joy stick) of the remote system is a main theme in the Public Works Research Institute (PWRI). In the report of this year, when the operator controls construction machine directly or he controls it using remote system (he can check the situation of site only via monitor), the degree of achievement, construction efficiency and construction precision were inspected. The remote system which is based on the system used at Unzen was developed at PWRI.

Aug 1, 2013

By A. B. Szwilski

The paper outlines the factors taken into account for the selection of steel arch supports. The results are based on experience using the long wall system of coal mining where roadway closure can be extreme. Results of tests on scale-model steel arches and full-scale yield elements are also presented.

Jan 1, 1979