Search Documents

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By Kent Zehr

Suncor Energy Inc. is an integrated producer and refiner of oil and gas headquartered in Calgary, Alberta. The bulk of revenue comes from the Oil Sands Group (OSG) operating in the McMurray formation of the Athabasca Oil Sands. Located some 25 kilometers north of Fort McMurray, Suncor OSG began life in 1967 as Great Canadian Oil Sands, the first operator to successfully enter commercial production of synthetic crude oils from the area. For most of the last decade, dramatic growth has been the standard mode of operation for Suncor OSG. Production of synthetic crude first reached 100,000 barrels per day in 1997 and less than five years later is averaging in excess of 200,000 barrels per day. Within this dynamic organization, Suncor Extraction is the business unit that processes run-of-mine ore into clean diluted bitumen for Upgrader feedstock. Extraction also delivers and places the barren sand and process affected water into tailings storage in one of several ponds from which water is recycled to support the various processes. For reference purposes, Extraction on a typical day currently receives more than 400,000 metric tons of oilsand ore, which is all processed to water based slurry for separation in one of two extraction plants. Separated tailings are disposed of as a slurry and the cleaned bitumen froth is diluted with naphtha and sent to tankage for storage until required by the Upgrading Unit. As a consequence, on a typical day Suncor Extraction pumps more than 1,000,000 tonnes of aggressive slurry into and out of the two extraction plants.

May 1, 2003

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By E. A. Collins

I TAKE it that the papers presented tonight on the subject of Reconstruction, as regards both gold and base-metals, are intended primarily to stimulate discussion of this important subject and, in regard to base-metals in particular, cannot in any manner be considered as a policy or plan to be followed as a panacea for all the ills which are bound to beset the industry when peace is declared. A famous cook-book written by a Mrs. Beeton contained a recipe for jugged hare which began with the instruction, "First catch your hare". To date, we have not caught the hare of victory and it may seem to many that any thought, energy, or effort devoted to the problem of reconstruction which will in any way impede the acceleration of the chase after victory will leave us open to the charge of being derelict in our duty as citizens. Much of our present trouble is due, however, to our lack of preparation for war in time of peace, and it follows that it is of equal importance in our national economy to prepare for peace in time of war. Most of us here tonight have vivid and sad memories of the chaos in the metal mining industry following the Great War of 1914-1918. In our own industry, mining, smelting and refining of nickel and copper, it was not a problem of absorbing the men who returned. There were only some three hundred who came back to the Mining and Smelting Division, and these men were all given their former jobs without any apparent difficulty. They were rehabilitated gradually due to the fact: that some of these men did not return for a year after the Armistice was signed. The numbers of men involved in the present conflict are much greater. We have to date in the armed forces upwards of 3,000 men enlisted from our employ.

Jan 1, 1943

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By L. Bichler, C. J. Verdon

In this work, the effect of doping yttria stabilized zirconia (YSZ) with 5, 10 and 15 mol% erbium oxide (Er2O3, erbia) was investigated using spark plasma sintering (SPS) technique. Sintering was carried out at 1300°C with 30 and 60MPa uniaxial pressures and a 5min hold time. Densification kinetics were studied using displacement response from the SPS machine. As-sintered microstructure characterization was carried out via scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques, while chemical composition was characterized by energy dispersive X-ray spectroscopy (EDS). The results suggest that sintering carried out at 60MPa produced high density composites even though erbia dopants were found to inhibit material densification and grain growth during sintering. 5, 10 and 15mol% erbia- YSZ had cubic crystal structures, as verified by XRD analysis.

Jan 1, 2014

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966