Search Documents

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By D. A. Barr

"Most of the lode and placer gold production in the Canadian Cordillera has been derived from mines and placers in the Intermontane and Omineca belts. Gold has been produced from rocks of Precambrian to Eocene age, but the preferred host environment contains Upper Paleozoic to Upper Jurassic eugeosynclinal or arc-type sedimentary and volcanic rocks adjacent to plutonic complexes which have a wide variety in both size and composition. Auriferous quartz lodes occur in fissures and shear zones which are commonly subsidiary to strong fault zones. In common with most vein-type deposits, structural complexities are an essential part of the mine environment.Gold production from the Canadian Cordillera to the end of 1978 totals 35.0 million ounces, of which 47 per cent has been produced from placer mining, principally in the Klondike and Cariboo districts. The balance has been derived from lode gold (80 per cent) and base metal (20 per cent) mines.Gold reserves in producing mines and deposits committed for production as of January 1, 1978 were 87.4 tons, or 21.6 per cent of total Canadian gold reserves contained in all types of deposits. Although more than 100 lode mines have operated in the Canadian Cordillera since the turn of the last century, over 75 per cent of the lode gold produced by 1978 was recovered from five mining camps, namely the Rossland, Hedley, Bridge River, Premier and Barkerville.The average grade of the principal producers in these camps was about 0.45 ounce of gold per ton. Individual camps yielded from 3 to 8 million tons during their operating lives, which varied from 28 to 43 years. The last of these mines ceased operating in 1971.Most of the total lode gold production has been derived from quartz veins, frequently with associated carbonate and ankerite, occupying fractured and faulted zones in Mesozoic volcanic and sedimentary rocks closely associated with a variety of intrusions. A review of the literature suggests that several deposits may have evolved by remobilization of ore constituents from earlier concordant gold-bearing formations. The principal metallic minerals in the deposits are native gold, electrum, tellurides, pyrite, arsenopyrite, pyrrhotite, sphalerite, galena and chalcopyrite.As the mineralogy suggests, many of the Cordilleran lode gold deposits have yielded important co-products or byproducts, including silver, copper, lead, zinc, cadmium and tungsten. Significant by-product gold production has also been derived from porphyry copper, volcanogenic, replacement and pyrometasomatic deposits, particularly in recent years.No major lode gold discovery has been made in the past 67 years, although little exploration activity for gold has taken place during the last 30 years. Several relatively small lode gold and gold replacement deposits have been discovered in recent years, either serendipitously (Chappelle) or on very low initial budgets (Northair and Carolin). Based on well-established precedents, one or more of these may eventually be developed into a large mine.A detailed study of the Canadian Cordillera gold deposits based on recent genetic models could prove rewarding, not only in up-dating information on their origin and depositional characteristics, but in stimulating the search for undiscovered gold deposits, in the Cordillera and other parts of Canada."

Jan 1, 1980

By C. M. Campbell

IN 1934 Newfoundland, after extravagant operation based on exaggerated ideas of what she had to work with, became bankrupt, ceased to be a self-governing Dominion, and passed into the hands of a Commission. Since the days of Dawson, Canadians have been taught that no country in the world is as rich as their own. This idea has become a religion; contrary views are heresy, and are suppressed even by technical organizations and government departments. Following the alleged habit of the ostrich, we have buried our heads in the sand and have refused to face the facts. This policy of "to have today and to hell with tomorrow" is now bearing fruit. After forty years of operation on the basis of unlimited natural wealth, with resulting over-expansion, wholesale depletion of capital assets, and huge borrowings, we are, now that our wealth has been shown to be very limited, face to face with the status of Newfoundland. Already, in this Province, commission government of bankrupt municipalities is not uncommon. The ostrich is referred to as the most foolish bird in the world. That is not the case-no ostrich ever hid his head in the sand. In the clear air of his home on the South African veldt, an area characterized by low bushes, he is a conspicuous object. When danger approaches, he lowers his head; matches his background, the bushes; and danger passes him by. This leaves the Canadian, with his head still in the sand, to fill the r61e cast for the ostrich. Fortunately, a few Canadians never did get their heads covered; others are getting them out far enough to see what is going on. Their comments are very much to the point. "Nowhere in the world," says Mr. Meighen, "has more harm been done to any country by an exaggeration of its resources and potentialities than has been done in Canada'.

Jan 1, 1941

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By F. W. Gray

Foreword: It is not my purpose, in this address, to write the history of the Geological Survey of Canada, which has from time to time been reviewed by the officers of the Survey itself, and by men more competent than myself to handle so large a subject, but rather to set out some of the reasons for the regard in which the Survey is held by our Institute, the body best qualified to speak for the mining men of Canada. And, a further purpose is to publish the desire of our Institute that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country. will permit, because to scrimp expenses on the Survey is 'to save at the spigot and lose at the bunghole." A historical examination of the grounds on which it may be asserted the Geological Survey has been, and still is, of fundamental economic value to our country, discloses a prescience on the part of the forefathers of Canada, calling for our admiring gratitude, and reveals a unanimity among the real leaders of Canadian thought, on the value of geological knowledge, that is impressive in its continuance dawn to this date. There seems always to have been before our people the realisation that large stretches of Canada are unfitted for agricultural settlement, and that our glaciated areas, the barrens and tundra of the North, and our extensive mountain ranges, had promise of compensating mineral content which the geologist and the prospector, labouring together through the years, would disclose. The Geological Survey is one of Canada's oldest public services, distinguished by an unimpaired tradition of honourable and useful labour. Founded in 1843, under William Edmond Logan, not yet 'Sir William', one year after the Act of Union, it was directed by him until 1869, or into the early years of Confederation, so that the early years .of the Survey were also, politically, the formative years of Canada, as we know her today.

Jan 1, 1932

By William D. Swank, Prabhat K. Tripathy, Tedd E. Lister, Eric S. Peterson, Delon C. Haggerd

More than half of the primary neodymium, produced directly from ores, is being used to manufacture neo magnets. Neodymium, being a critical element in supply, has attracted considerable interest worldwide to recover this metal from a variety of waste streams. From among different recycling processes, hydriding-dehydriding can prove to be highly effective in recycling discarded neo magnets present in consumer electronics. In the present study, manually removed magnets from discarded Hard Disk Drives (HDDs) were subjected to the hydriding-dehydriding process in order to evaluate the resultant products for the re-fabrication of the magnets. The paper describes the effect of experimental parameters on both the hydriding and dehydriding processes as applied to different magnet chemistries.

Jan 1, 2014

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By Denis Racicot

"L'Abitibi québécois a produit essentiellement de l’or, du cuivre, du zinc et de I' argent, ainsi que de faibles quantités de nickel, de plomb, de molybdène, de bismuth, de lithium, de fer et d’amiante. Depuis l’ouverture de la mine Horne en 1927, cent-cinquante mines ont contribué à la production de 1 420 tonnes d’or de 4,1 millions de tonnes de cuivre et de 4,7 millions de tonnes de zinc. Les productions minières annuelles ont été d'importance variable: des records de production ont été établis en 1955 pour I' or avec 35 tonnes et, vers 1965, pour le cuivre, le zinc et la quantile globale de minerai extrait avec respectivement 130,000, 275 000 et 13 millions de tonnes. Deux dépressions généralisées ont eu lieu, l’une vers 1946 et l'autre, a lafin des années soixante-dix. Des ralentissements de la production ont été observes pour le cuivre en 1953 et le zinc en 1959. Depuis le debut des années quatre-vingt. I' or et, de façon plus irreguliere, le zinc sont en progression, landis que le cuivre, malgre une hausse en 1983. pour suit son dec/in.La teneur de récupération des mines d’or est demeurée régulière et n’a subi qu’une faible diminution au cours des quarante dernières années. Célie du cuivre a diminué d'environ 50% dans la même période, landis que celle du zinc a subi d’import antes variations, aussi bien positives que négatives. Près des trois quarts des mines d'or ont une durée de vie inférieure à 12 ans et la distribution des tonnages de minerai extrait montre un maximum pour la classe de 100 000 à 1 million de tonnes. Du cote des mines de métaux de base, la durée de vie est plus étalée et les volumes de minerai ont une occurrence maximale dans la classe de 1 à 10 millions de tonnes.Concernant la distribution géographique de la production minière dans l'Abitibi québécois, le camp minier de Rouyn-Noranda vient en tête pour l’extraction de minerai et la production d’or et de cuivre. L’est sui vi par le camp de Val d'Or pour le minerai et l’or, landis que le camp de Chapais-Chibougamau occupe la deuxième place pour le cuivre avec une production équivalence a 60% de celle de Rouyn-Noranda. Le camp de Cadillac-Malartic suit de tres pres celui de Val d'Or pour ce qui est de I' or. Finalement, dans le casdu zinc, le camp minier de Joutel-Matagami domine largement avec une production qui a connu un développement accélère depuis 1963. Une analyse pré liminaire de ces données indique qu' i/ subsiste unpotentiel encore élevé de production d'or, décuivre et de zinc dans I' Abitibi québécois. ABSTRACTThe Quebec portion of the Abitibi belt has essentially produced gold, copper, zinc and silver, as well as some small quantities of nickel, lead, molybdenum, bismuth, lithium, iron and asbestos. Since the opening of the Horne mine in 1927, one hundred and fifty mines have produced 1420 tons of gold, 4,1 millions tons of copper and4,7 millions tons of zinc. Annual mine production has fluctuated: production records were established in 1955 for gold with 35 tons, and around 1965 for all extracted ore copper and zinc with respectively 13 millions, 130 000 and 275 000 tons. Two main recessions have occurred, the first around 1946 and the second during the late seventies. Cut backs in copper and zinc production occurred in 1953 and1959. Since the beginning of the eighties, gold production and to a lesser extent zinc production have been in progression. Except for a small jump in 1983, copper production is still declining.The average recuperation grade of gold mines has been quite steady and has only slightly diminished in the past forty years. The average copper recuperation grade was halved during the same time interval. For zinc there have been important ups and downs. At least three quarters of gold mines have an average lifespan of 12 years the tonnage distribution shows a peak in the 100 000 to 1 million tons class. Base metals mines show a more widespread life expectancy and have a tonnage peak in the 1 to 10 millions tons range"

Jan 1, 1990

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the PLS and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. In this paper, purification of vanadium leaching solution using organophosphorus, solvating and amine extractants will be reviewed. This review will be focused on vanadium separation from iron, molybdenum and uranium which are often present in vanadium resources including primary ores, fly ashes and spent catalysts.

Jan 1, 2014

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

Presentation Outline Introduction Deposit Characteristics Geology Grade, Value and Tonnage Estimates 2006 Advanced Program Drilling Bulk Sampling DMS Test Facility 2006 Exploration Summary

May 1, 2006

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965

By D. Neely, D. Milne, L. R. Feldman

"Resin-anchored rebar is commonly used for rock support in mining. The rock properties and environment determine the average bond strength, allowing mine engineers to select the appropriate length and installation pattern for the support. In weak material such as potash, the average bond strength tends to be lower than for a typical hard-rock installation. Determining the failure mechanism by which the support fails in soft-rock applications could lead to improved bond strength and better calculated installed support capacity. This paper reports on research conducted at a potash mine in Saskatchewan and analyzes the failure mechanism of the support.RÉSUMÉ Dans les mines, les barres d’armature enduites de résine sont fréquemment utilisées pour soutenir le roc. L’environnement et les propriétés du roc déterminent la résistance moyenne d’adhésion, permettant ainsi aux ingénieurs miniers de choisir la longueur de barre appropriée et le diagramme d’installation du soutien. Dans des matériaux faibles, tels que la potasse, la résistance moyenne d’adhésion tend à être plus faible que pour une installation typique dans de la roche dure. La détermination du mécanisme de rupture selon lequel le soutien fait défaillance dans des roches tendres pourrait conduire à une meilleure force d’adhésion et à un meilleur calcul du soutien installé. Le présent article fait état de la recherche effectuée dans une mine de potasse en Saskatchewan et analyse le mécanisme de défaillance du soutien. ,"

Jan 1, 2016