Search Documents

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

By Eugene F. Mehr, Dennis C. Martin

"Development of the final slope for the 340 m (1200 ft) high hanging wall at Cassiar Mine precipitated an area of deep seated instability involving an estimated 17.6 million tonnes. The deformation mechanisms involved squeezing of soft deformable serpentinite rocks in the toe which caused planar sliding and graben toppling of the stronger sedimentary rocks in the middle and upper sections of the slope. Although movement rates up to 150mm/day were recorded, by understanding the controls on failure, the mine was able to install a suitable monitoring system and complete the open pit with only minor loss of the mineable ore. Accelerated mining was required in the last full year of operation. This paper describes the deformation behaviour, failure mechanisms and back analysis results for the failure. The monitoring systems and operational aspects related to the failure are also presented.IntroductionCassiar Mine is located in steep mountainous terrain in northern British Columbia approximately 1200 km north of Vancouver (Fig. I). During the final mining phase of the open pit, instability developed in the approximately 340 m high hanging wall (east wall) slope. A unique graben toppling mechanism was identified based on detailed assessment of slope monitoring data and visual observations. Comprehensive slope monitoring enabled mining to continue even though movement rates as high as 150 mm/day were being recorded. Three-dimensional limit equilibrium back analyses and numerical modelling have been used to assess the various controls on the slope movements and to understand the failure mechanism."

Jan 1, 1993

By Rick Steen, Weldon Read, Morrism Tracy T.

Edging for starter sheet blanks used in conventional copper refineries has always been problematic for getting the edging to seal and adhere to the titanium material used for the blank so that copper is prevented from plating under the edging and cause undo problems in getting the copper sheets to separate from the blanks. A method was developed at the Amarillo Copper Refinery utilizing an injection molding process that better adheres the edging material to the titanium that makes the harvesting of starter sheets much easier to the point that robots are now used to strip with and which holds up very well to the unforgiving physical nature of the electroplating process. It is believed that this technology could be successfully utilized for permanent cathodes as well. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery. The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By A. Dave Mackintosh

The Current demand for potash has pushed world prices to record levels and allowed Saskatchewan producers to operate at maximum capacity. Several years of strong demand has resulted in a permitting rush not seen since the 1960?s. Even though Saskatchewan has a huge potash resource, mining and processing constraints will limit the areas of economic development. Introduction In 1969 M. E. Holter prepared a report ?The Middle Devonian Prairie Evaporite of Saskatchewan?, published by the then Dept. of Mineral Resources. Holter?s report has remained the bible of geologists working in potash ever since. It is astounding that a report written before there was really much potash mining history in the province, is as valid today as when it was first published. This paper re-iterates much of Holter?s report and adds a little mining experience to essentially confirm the importance of his work.

May 1, 2008

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By X. -G. Chen, A. M. Nabawy

A novel manufacturing technique for Al-TiB2 nanocomposites has been developed, in which TiB2 nanoparticles were incorporated into liquid aluminum under mechanical stirring and in the presence of a K2ZrF6 flux-wetting agent. The microstructure of the Al-TiB2 nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microhardness test was conducted to investigate the strengthening effect of TiB2 on the aluminum matrix. The TiB2 nanoparticles were successfully incorporated and dispersed into the aluminum melt in the presence of the K2ZrF6 flux during mechanical stirring. In the as-cast microstructure, most nanoparticles segregated in the interdendritic regions as a result of particle redistribution during solidification. The addition of 2, 5 and 10 wt% TiB2 nanoparticles increased the composite hardness by 60, 90 and 150% respectively when compared to commercial purity aluminum, indicating that the TiB2 nanoparticles imposed a significant strengthening effect on the aluminum matrix. The role of K2ZrF6 flux agent on the incorporation of nanoparticles into aluminum melt was discussed.

Jan 1, 2014

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013

By Edgar L. Horner

"The objectives of the Wabush Mines tailings stabilization program are to control dust Ii/t-off and to rehabilitate the disposal area. The evolution of the program started with test plots in 1970, these being continued and expanded upon through 1974. In 1976, a 35-acre vegetation field trial was attempted and failed, part of the failure being attributed to lack of adequate equipment. Subsequently, equipment was purchased and during the summer of 1979-80 extensive areas were treated. The program was also expanded to include the evaluation of chemical and water spray stabilization versus vegetation in areas where shorter-term control is required. In addition, during the summers of 1979-80, spruce bog material was spread over about 100 acres and seeded.The approach to reclamation by vegetation at Wabush is one of soil building. Work to this point indicates that iron ore tailings can be converted to a soil capable of supporting plants. Plans for the Wabush tailings disposal area should make dust lift-off from inactive tailings areas negligible within the next few years."

Jan 1, 1981

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

RÉSUMÉ Cet article traite d’une analyse technique et économique du concept du triage optique en vue d’améliorer la rentabilité des opérations minières. Le principe du tri optique et les principaux systèmes et modules servant au fonctionnement de l’appareil de triage sont décrits. un modèle a été développé pour analyser l’intérêt économique d’une opération de triage optique. L’étude est basée sur des données provenant d’une halde de minerai à faible teneur en or, déposé à la surface, et de minerai extrait des opérations souterraines courantes de la mine Beaufor au Québec. Les résultats de cette analyse indiquent que l’opération de triage optique permet d’améliorer grandement la performance économique; l’opération devient alors rentable pour des teneurs en or relativement petites.

Jan 1, 2010

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By E. Topuz, C. Duan

"INTRODUCTIONOperations research (OR) applications have experienced a substantial growth within the mining industry during the last three decades. The purpose of this paper is to present a summary of the results of a comprehensive survey of the application of various OR techniques to the major mining activities. It is hoped. through this sur vey , that the most widely used OR approaches, the important areas of application, and future trends have been identified.This survey included more than 500 articles published in this field in English since the late 1950s. Most of the relevant literature was found in mining publications, but, in terms of quality and originality, important applications were also found in literature not related to the mining industry. The sources constituted periodicals, proceedings research reports, and a few books. A listing of selected publications from which three or more articles reviewed in this survey appear is given at the end. Operations Research MethodologiesOperations research is concerned with optimal decision making in, and modeling of, deterministic and probabilistic systems that originate in real-life situation s. One basic feature of the OR methodologies is the attempt to optimize certain design parameters, subject to a set of constraints. This distinction has been employed in the survey as a guideline for selection of the techniques covered under the title "" OR methodologies"". The methodologies thus encountered in the literature are listed below. In a few cases, simulation has not been considered because it is not an optimization method per se."

Jan 1, 1989

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

"The Hardy Cross algorithm offers a reliable method of solving network systems of fluid flow and has become widely used for solving water and ventilation flow networks. A limitation is that computational iterations and time to solve a network rises rapidly with the size of the model and modern detailed ventilation networks have typically grown to thousands of airways. Non-linear matrix solving methods can offer improved performance, however these are more complex and may be unstable if initial estimates are poor. This paper presents improvements that can be applied to the traditional Hardy Cross algorithm to greatly reduce iterations and solving time for large ventilation models. INTRODUCTION The Hardy Cross algorithm (Cross, 1936), was originally developed to solve water flow in city and urban pipe networks. Using principles of Kirchhoff’s electricity current laws, Hardy Cross developed an iterative algorithm for solving non-linear equations associated with network water flow. Traditional network analysis research refers to the various members of system networks as branches, nodes and meshes. This terminology has been changed in this paper to airways, junctions and loops respectively which are terms more familiar to engineers in mine ventilation. When Kirchhoff’s laws are applied to fluid networks, the following assumptions can be made: •The sum of fluid flows into a junction must equal the sum of fluid flows out of the junction.•The sum of pressure losses around any loop through a network system must be equal to zero.An iterative solution can therefore be achieved by initially guessing flow in a network, calculatingthe pressure losses around the network loops (Figure 1), and applying flow corrections using Newton’s method for each loop if the sum of the pressure losses does not equal zero. To solve the system, a loop must be defined for every segment or series of segments between a junction of 3 or more airways.The Hardy Cross algorithm has been used extensively for ventilation network analysis since the introduction of the first electronic computers (Tien, 1997), however numerous other variations and methods have since been developed through the use of matrices to solve the required system of nonlinear equations. Commonly used algorithms such as the Newton Raphson method (Brown, 1969), the Gradient method (Todini & Pilati, 1988), the Linear Theory method (Gupta & Prasad, 2000), and Coupled Network Solver (G. Danko, 2008) have found general use in fluid flow network solvers (Rossman, 2000). Despite poor and sometimes unpredictable convergence performance however, the Hardy Cross algorithm still has unique properties that make it attractive for ventilation models. Some benefits are:"

Jan 1, 2019

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By J. Elbrond

"This paper describes qualitatively the progressive are losses and rock dilution in a mining project from the geological modelling to and including the concentration. A simple theoretical model of the net present value of a deposit, assuming a log-normal grade frequency function, is used to find the pair of decisions on rate of production and cut-off grade, which maximizes the net present value. Various degrees of ore losses and rock dilution are then applied on this optimum, and the resulting decreasing net present values are calculated, as well as the increasing cost of metal and the increasing metal losses as a function of are losses and rock dilution.IntroductionDue to a variety of uncertainties, to inevitable lack of precision in deposit estimation and in mine planning, and due to production constraints, ore losses and rock dilution occur throughout the many phases of a mining project. The phases range from the geological definition of the orebody, over the cut-off grade optimization and decision, over the design of the mining method and the actual mining to the ore dressing, where the final loss of valuable ore into the tailings occurs. Quantification of ore losses and rock dilution are mostly difficult if not simply impossible to obtain. At the end-phase an estimate of the total dilution may be obtained with some degree of precision by observations of the amounts and analysis of concentrate and tailings. It is much more difficult to estimate the total ore losses because the uncertainty of the geological modelling in the initial phase and in the mining phase is very difficult to quantify, despite the use of geostatistics for grade estimation.Many attempts at quantification of ore losses and rock dilution have been made and some examples are shown in Table I. Although they differ widely from each other, it is obvious from these figures that ore losses and rock dilution are significant and have considerable effects on the economical results of a mining operation. Life length, net present value, cost of producing metal and the loss of metal are all affected."

Jan 1, 1994

By E. M. De Souza, R. Penner

"Water is encountered at the majority of underground mines, both over their lifetime and during each stage of development and production. The dewatering system is one of the most important and costly components of an underground mining operation and it is often not well designed and analyzed. An effective design of a mine dewatering system will greatly reduce its energy cost as well as improve working conditions and reduce production costs. A computer-based system, called Qpump, has been developed to assist the underground operator to effectively design and/or assess over-all and local mine dewatering systems. The design features and principles used in the development of Qpump are introduced and an example which illustrates typical applications is presented.IntroductionTraditionally, dewatering operations have been given lower priority than many other operations in underground mining. Invariably water will be encountered during the sinking of the mine shaft, during development and subsequent production. The dewatering system thus becomes a very important component of an underground mine operation and, in fact, any mine manager will attest to the importance and necessity of an efficient mine dewatering system.The water problem is of varying importance at different mines. There are several factors that contribute to the water encountered. It is a function of the mining method and techniques utilized (backfill system, drilling and raising technology, dust control sprays, shaft water rings, etc.) and of prevailing conditions (ground water, rock structure and permeability). In some cases a mine may be so dry that little pumping is required while in others, the weight of water pumped may exceed by many times that of ore mined.The successful design and application of a mine dewatering system is dependent upon the operating conditions of each specific operation. There are no standard procedures and systems which can be used for all mining situations. However, an effective water system will greatly reduce the energy and production costs of a mine, improve working conditions and eliminate headaches because of flooded working places."

Jan 1, 1993

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973