Search Documents

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By Michel L. Bilodeau, Brian W. Mackenzie, Dallas W. Davis

"The paper formulates an evaluation procedure for examining the effects of location on the economics of developing mineral deposits. This methodology is applied to assess locational aspects of Nova Scotia's competitive position f or mine development relative to other Canadian regions and provinces. The appraisal concerns two representative mine development opportunities, a medium-size open-pit tungsten deposit, and a small underground gold deposit. The influence of regional economic conditions is initially assessed. Then, the consequences of taxation are isolated. Finally, the combined impact of regional and taxation conditions is examined. SettingThe economic potential of mining may be assessed in a number of ways. One approach, increasingly used for both corporate planning and government policy purposes, is to evaluate the competitive position of an actual or potential mineral producer in the international marketplace relative to other suppliers.Such examinations of competitive position vary from cost league comparisons of breakeven costs for operating mines, through the assessment of medium-term costs associated with developing new mine capacity, to long-term evaluations of the economics of mineral supply from the start of exploration. The complexity of the analysis increase s with the scope and timeframe of interest. Many factors are involved. One component of competitive position is the quality of the mineral resources available. Other key factors include existing technology, wage and salary rates, labour productivity, the cost of capital, infra structure requirements, distances from sources of materials supply an d to mineral markets, management attributes, organizational efficiency, government mineral policies (particularly taxation), and inflation and exchange rates. The paper fits within this competitive position framework.The variable economic conditions which exist within Canada have a direct bearing on the viability of mine development and, thereby, on mineral exploration potential. The paper examines locational aspects of Nova Scotia 's competitive position."

Jan 1, 1986

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By B. R. MacKay

Introduction Of all Canada's mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By J. E. Danoczi

ABSTRACT A diamond processing plant is being designed for the Star–Orion South diamond project in central Saskatchewan. Key to the plant is diamond liberation, which occurs in the comminution section and is the process of breaking up kimberlite rock as gently as possible to minimize diamond damage, particularly in larger, high-value diamonds. Kimberlite from the crater area of a volcanic pipe is generally softer than kimberlite from the diatreme zone. Softer kimberlite, comprising the majority of Star– Orion South deposits, can be readily broken up using abrasion and attrition by autogenous grinding mills, the preferred comminution method for minimizing diamond damage.

Jan 1, 2013

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By F. Rashchi, A. Ghahreman, J. Moghaddam, S. Karimi

"In this work, the kinetics of ferric-ferrous redox reaction on a passivated sphalerite electrode is studied by the application of chronoamperometry method in 0.5 mol L-1 H2SO4 solution. The electrochemical behaviour of ferric and ferrous couple was investigated on two sphalerite minerals acquired from two different geological regions (Iran and Canada). The carbon paste electrode (CPE) of sphalerite was initially prepared and passivated in 0.5 mol L-1 H2SO4 solution and after reaching the steady-state condition, ferric and ferrous sulfate solution was added. The registered current density differences between the current density of the passivated electrode and that of the electrode in the iron salts added solution were interpreted for kinetics of ferric-ferrous reduction-oxidation reaction. The equilibrium potential for ferric-ferrous couple on sphalerites surface was about 500 mV vs. Ag/AgCl. The exchange current density (i0) for ferric-ferrous redox reactions on the sphalerite samples had the same magnitude of 10–6 A cm–2. The electrochemical impedance spectroscopy (EIS) measurements at 550 mV vs. Ag/AgCl illustrated that sphalerite oxidation was controlled by two charge transfer process in both of Fe-free and Fe-containing solutions. The charge transfer resistance remarkably decreased when Fe salts added to the 0.5 mol L-1 H2SO4 solution, owing to the ferric-ferrous redox reactions being the predominant reactions on sphalerite surface.INTRODUCTION Direct atmospheric leaching processes for sphalerite concentrates are performed by reduction of an oxidant (e.g. ferric ion and oxygen) and oxidation of sphalerite to zinc ions. Oxygen could be an oxidizing agent as well, but the concentration of oxygen is very low in the solution. The role of ferric ions is predominate in this oxidation (Babu, Sahu, & Pandey, 2002). The oxidation reaction for sphalerite in the presence of ferric in can be presented as follows (Lampinen, Laari, & Turunen, 2015):"

Jan 1, 2017

By S. Makni, S. Koppalkar, A. Bouajila

This paper reviews briefly the gravity recovery involving conventional gravity separators and centrifugal gravity separators. The advantages of semi-continuous gravity separators will be discussed. Techniques for upgrading the gravity concentrates will be addressed briefly. The research efforts in optimizing semi-continuous gravity separators will be recalled. Innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. On-going gold gravity research at COREM has revealed that gold particle shape transformation is the main factor explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving gravity recovery at plant will be discussed.

Jan 1, 2011

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

HIGH LAKE PROPERTY --HISTORYHISTORY -19501950??s ??Kennarctic Exploration discovers Exploration sulphides (A/B & (D Zones) at High Lake during helicopter reconnaissance exploration program.- -1991 93 Aber signs agreement to earn in to the High Lake Property from Kennecott. 63 holes drilled, primarily testing the known deposits. -2001 Wolfden purchases 100% interest in High Lake from Kennecott and Aber -2002 Wolfden performs helicopter borne TEM Survey over the High Lake Greenstone Belt. -2003 West Zone was discovered following UTEM & Gravity Surveys (performed by Teck Cominco ) over an airborne anomaly approx. 1km west of the known deposits. -2004 Wolfden awarded Bill Dennis Prospector of the Year

May 1, 2006

By H. V. Kinsey

"IntroductionTITANIUM is probably the most widely publicized metal today. Much has been written, both in the lay press and the technical press, about its properties and potentialities. In view of the fact that Canada possesses large quantities of titanium-bearing ore, and could conceivably become a major producer of metallic titanium, it was felt that a paper dealing mainly with the physical metallurgy of titanium would be of interest to this Institute. This paper is concerned chiefly with the useful properties of titanium and its alloys and the fundamentals governing the modification of its properties by alloying.Physical Properties of TitaniumTitanium belongs to a family of metals that have been termed 'gas sensitive' (I), because their mechanical properties are altered by certain gases which they readily absorb and retain. Other metals of this group are zirconium, hafnium, vanadium, columbium, tantalum, and chromium. Titanium has a strong affinity for oxygen and nitrogen and once it has absorbed these gases they cannot be removed either by melting in vacuum or by any degassing agent. These gases, when present in excess of about half a per cent oxygen plus nitrogen, render the metal brittle and useless as a structural material.Some of the typical physical properties of titanium are listed in Table I along with those of common structural metals for comparison."

Jan 1, 1953

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Testwork was conducted in order to compare the effectiveness of carbon based catalysts while oxidizing a gold-bearing pyrite concentrate under atmospheric conditions. Without the use of a catalyst the oxidation of pyrite was incomplete after 96 hours, resulting in roughly 60% pyrite oxidation. Furthermore the resulting sulphate yield from unassisted pyrite oxidation ranged between 72 and 84%. It is evident that atmospheric oxidation of pyrite is not viable due to slow oxidation kinetics and high sulphuric acid production when using a ferric sulphate media without a catalyst. The effect of two different carbon based catalysts, one Lewatit® AF 5 a new microporous carbonaceous bead, and the second a granular coconut shell based activated carbon, were tested under the same oxidation conditions as the unassisted pyrite tests. After 96 hours, Lewatit® AF 5 assisted oxidation showed approximately 96% pyrite oxidation with a sulphate yield ranging between 26 and 35%, while the activated carbon assisted oxidation reached approximately 100% pyrite oxidation with a sulphate yield between 36 and 37%. Testwork indicated that not only does the addition of a carbon based catalyst greatly improve the oxidation kinetics and lead to almost complete oxidation, the sulphate yield is also drastically reduced, resulting in very high elemental sulphur yields.INTRODUCTION Pyrite is an important sulphide mineral due to its ability to contain invisible gold concentrations up to 132 g/t (Chryssoulis & Cabri, 1990). As a result, ores composed of only a small amount of pyrite still have the ability to contain high gold grades. This refractory gold cannot be accessed via conventional gold leaching processes, such as cyanidation, and additional oxidative pre-treatment is required to liberate the gold, making it more amenable to extraction (Marsden & House, 2006). Current oxidative pre-treatments do exist consisting of both pyrometallurgical and hydrometallurgical processes including high temperature and high pressure leaching within autoclaves, biological atmospheric leaching and roasting. Autoclaves are a proven process reaching desirable recoveries within approximately a 1–2 hour retention time, due to the increased temperatures and pressures, allowing for an increase in dissolved oxygen (Marsden & House, 2006). The typical reaction for pyrite oxidation within autoclaves is presented in Equations 1, 2 and 3."

Jan 1, 2017

By J. S. Roper

"IntroductionSNOW LAKE is situated in northern Manitoba at latitude 54° 55 and longitude 100°, 400 miles northwesterly of Winnipeg, 80 miles northeast of The Pas, 80 miles east of Flin Flon. A 38-mile road from Wekusko, on the Hudson's Bay railway, serves the community.The mine is located in and close to the southern edge of the Precambrian Shield in typical low-relief muskeg and lake country.The Howe Sound Exploration Company, Limited optioned the property from Nor Acme Gold Mines, Limited, after preliminary diamond drilling had outlined two orebodies of low-grade arsenical gold ore.Following the examination and study of geological data and of 50,000 feet of diamond-drill core, and metallurgical tests made during 1942 to 1945, a decision was made to develop the mine and build a 2 ,000-ton mill concurrently. This development has been described by G. C. Lipsey in a paper entitled The Development of a Mining Operation from Diamond-Drill Data which was published in the August. 1952, issue of Mining Engineering.Geological Features of the OrebodiesThe orebodies at Snow Lake occur in volcanic rocks of acid to basic composition and, to a lesser extent, in intrusive hornblendite. The hornblendite is a massive, uniform, .coarse-textured rock except in the immediate vicinity of the ore zone, where it becomes sheared and carbonatized. The acid volcanics have been converted to quartz-garnet-biotite gneiss, and the basic volcanics to amphibolite gneiss. Orebodies have been formed by the replacement of all three rock types."

Jan 1, 1955