Search Documents

The kinetics of the hydrogen reduction of iron oxides in granular calcined bauxite were studied at 550-1,050°C in a shallow bed reactor. The iron oxides behaved as a dispersion of particulate iron oxide in a porous alumina matrix in which the iron oxide particles were reduced independently. The observed rates of reaction were found to be virtually independent of the bauxite grain size. At 800,°C and above, the reduction was multistage, Le.1. Fe203 +2Al203 (matrix) ?2FeAl204, and2. FeAl204? Fe0 +Al203.Reaction 1 was very rapid. Reaction 2 was much slower, the latter stages being controlled, at least in part, by phYSIcal changes of the Fe0 and a-Al203 produced in the reaction. Owing to the observed nature of the material, the reaction rate controlling steps could not be determined.

Jan 1, 1972

Drainage aids are designed to assist in filter cake dewatering by reduction of surface tension. By the early 1980's severalspecialist chemical manufacturers had developed drainage aids specific to the alumina industry. Thus, after some initial laboratory work, drainage aid addition to the product hydrate filter cake was first tried at Gove in early 1981. Encouraging results led to further plant trials and a laboratory trial comparing eight different products. Fromthis last trial a product was chosen and a plant trial run in March 1982. The results achieved encouraged a further plant trial to be run during April and May, 1982 and a decision was then made to adopt the full-time use of drainage aid on the plant.Optimisation work with the drum filters and drainage aid continued until late 1983. This work not only led to optimisation of dose rates, concentrations etc., but also to significant improvements in the mode of operation of the product filtration area.

Jan 1, 1985

By X B. Sun

Mining work is a high-risk operatation under a special environment. It is affected by space, lighting, noise, vibration, dust, air pollution, etc as well as coal seam conditions, complicated geology construction, combustion of coal, gas, coal dust, etc. Factors which affects safety production are numerous, eg natural conditions, technical equipment level, producersÆ and managersÆ qualities. It is a complex system engineering to ensure mining safety and high efficiency. Among the ideology, methods and measures of safety management are the most important factors besides safety technology. Mine productive environment is a main problem that affects minerÆs work as far as safety and health are concerned. Combining ChinaÆs mine productive environment situation and using human ergonomics theory, this paper explores a series of measures and suggestions as to how to reinforce safety management, how to build up the safety management ideology, how to improve the mine production environment, how to decrease coal mine accidents, and how to ensure mining safety and high efficiency.

Jan 1, 2003

By S Jahanshahi, T Norgate

In single stage copper making appreciable amounts of copper report to the slag phase. Various strategies are available to minimise copper losses to the slag. However a slag treatment stage is likely to be required in an economically viable process. A number of slag treatment process options are available and include: flotation, leaching and thermal reduction. In the design of an industrial process some type of economic as well as technical analysis of these options will be required. In this paper an outline of the techno-economic analysis procedure used to design a single stage copper making process is presented. The calculated operating and capital costs of industrial copper making processes are compared and used to determine the optimum single stage copper making flowsheet. The most economic slag treatment options is flotation of slags containing low amounts of copper.

Jan 1, 2000

By M Eichorn

Running a successful reagent plant trial is not an easy task, especially when trying to achieve an incremental improvement in a highly variable process, such as flotation. Cytec aims to achieve one per cent recovery improvement with 90 per cent statistical confidence. Most concentrators experience large fluctuations in recovery and so the æmagicalÆ one per cent is difficult to detect. With the aid of statistical software, including REFDISTR (proprietary) and ECHIPR, Cytec have developed a unique approach to differentiate between daily operational variation and actual process improvement. This paper describes how Cytec runs a plant trial based on extensive laboratory investigation and detailed analysis of historical plant data using statistical techniques.

Jan 1, 2000

By S A. Johnson, J Cassidy, J L. Mauk

Geophysical anomalies at Puhipuhi reflect both diverse lithologies and different degrees of hydrothermal alteration. Most significant is a strong negative gravity anomaly (up to 50 g.u.), encompassing but extending beyond areas of known alteration, which is modelled as a deep zone (up to 3 km) of reduced density in the host greywacke basement. This zone, interpreted as being due to alteration (at least in part), closely correlates with the extent of overlying basalt flows. The gravity data indicate that the most intense alteration occurs below the basalts and correlates with the location of previously inferred hydrothermal upflow zones. These observations suggest that the basalt may have acted as a cap rock to a mineralising geothermal system. Aeromagnetic data identify highly variable but typically low magnetisations in the basalts which suggests that alteration may have been contemporaneous with volcanism. These geophysical data at Puhipuhi confirm the locations of centres of known alteration and suggest potential exploration targets below the basalt cap where there is no surface manifestation of alteration. Further implications of these results are discussed in Locke et al. (1999).

Jan 1, 1999

By D J Rawlings

The Palaeo- to Mesoproterozoic McArthur Basin contains a thick (-10 km) intracratonic platform cover sequence of unmetamorphosed and relatively undeformed sedimentary and volcanic rocks (Pietsch et al, 1991). It covers an area exceeding 180 000 km2 of the North Australian Craton (Figure 1), overlying segments of the older deformed basement and transitional igneous units. Volcanism in the basin (including transitional domain) followed a four-phase pattern. These phases are geologically distinct and widely distributed, and are also recognised beyond the McArthur Basin in many similar-aged tectonic provinces in northern Australia. The four phases are described briefly below. Regional and structural nomenclature used refers to Figure 1. A stratigraphic correlation diagram is presented in Figure 2.

Jan 1, 1994

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the projectÆs life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

By S Totsuka, P Ortiz, E Prokkola

Electrochemical polarisation techniques can be successively applied to maintain clean surfaces in process environments. The applications are the result of extensive knowledge of the electrochemical nature of process environments, an innovative approach to problem solving and shared æcan doÆ attitudes between the supplier and process owner. Initial identification of suitable applications is based on over 20 years of process and electrochemical experience. The technologies discussed in this paper include Electrochemical Anti-Scaling [EAS], Electrochemical Protection Systems with both anodic [EPSA] and cathodic [EPSC] protection and Electrochemical Flocculation [EF]. Examples of industrial applications are reviewed. Good examples of metallurgical processes which can benefit greatly from an advanced electrochemical treatment are the wet processes involving precipitation, crystallisation and evaporation. Eliminating corrosion and scaling which would otherwise cause process disruptions and quality problems can make a big difference in process profitability. Clear advantages in both cost efficiency and environment friendliness are easily demonstrated. Continuous processing with minimum downtime is one clear advantage. In comparison to the use of corrosion inhibitors, anti-scaling agents and flocculants, the electrochemical polarisation does not increase the environmental load from the process as no additives of any kind are used. In most cases the cost benefits from pro-actively keeping surfaces clean with the help of advanced electrochemistry are substantial when compared to traditional re-active methods and other active treatments.

Jan 1, 2004

This short paper outlines the authorÆs views regarding the progress we have made as an industry in managing mining assets over the past 500 years. It represents a personal view û but one founded in fact-based observations of mining companies and of the mining industry in general. There is no doubt that AgricolaÆs views as expressed in De Re Metallica (1556) were visionary. There is also little doubt regarding another issue û that whilst a great deal has been learnt about the management of mines since AgricolaÆs time, observations suggest that best practice management is the exception rather than the rule across our industry. Although insights regarding the successful management of mines have become apparent, we still witness unnecessary errors in our industry that lead to the loss of shareholdersÆ funds. By highlighting some aspects of current best practice, particularly in the arena of operations management, it is hoped that this short paper contributes a small step along the next 500-year-long learning curve. The paper concludes with a brief description of the progress and impact of continuous improvement initiatives at Kalgoorlie Consolidated Gold Mines (KCGM). Located in the Kalgoorlie Goldfields, KCGM is currently AustraliaÆs largest gold mine producing over 800 000 ounces of gold per annum. Improvement initiatives at KCGM look set to deliver some $100 million in value over life-of-mine.

Jan 1, 2004

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987

By P Walton, L W. Armstrong, D P. Blair

Sydney is the capital city of NSW and has a population of approximately four million people. Eighty per cent of the cityÆs water is supplied by Warragamba Dam, which is situated some 75 kilometres south west of the city centre. A risk assessment was carried out on the dam and future predictions of water flows into the catchment area showed that there was a risk of a one in 700-year flood not being contained by the dam. The predicted loss of life and property damage warranted the construction of an auxiliary spillway on the eastern side of the existing dam to cater for any uncontrollable influx of water. A test blasting program was instigated and the blasting parameters were established that would lead to routine production blasting of the sandstone rock making it more cost effective to excavate. Blast induced vibrations were a concern to the owners and the dam wall and ancillary infrastructure was instrumented with sensitive vibration monitoring equipment during the test blasting phase of the operation. Once the blasting parameters were established from the testing program production blasting was carried out on a daily basis to maintain æstockpileÆ of fragmented ground for the excavation equipment. Blast vibration models were developed to predict vibration levels for more sensitive areas of the dam to give the operators more confidence in their operations. The blast induced vibration levels recorded did not cause any structural damage to the dam wall and the waveform frequencies of the blasting operation were much higher than that experienced during a recent earthquake. The integrity of the SCAÆs assets were at no time jeopardised.

Jan 1, 2001

By Wauchope AMH

Arsenic residues from BHAS Refinery operations are currently treated to form a calcium arsenic compound and stored in lined dams on site. Laboratory and large scale work on these residues has resulted in the development of a hydrometallurgical process for production of arsenic trioxide. The process also recovers the material from the storage dams. The residues are hot water leached to produce an alkaline arsenic liquor. This liquor is mixed with material from the storage dams and lime to form a calcium arsenic precipitate. The precipitate is then reacted with sulphuric acid to form gypsum for return to the main plant, and an acidic arsenical solution. Metallurgical gas containing 3-6% sulphur dioxide is bubbled through the solution and on cooling arsenic trioxide is precipitated. The product contains in excess of 95% arsenic trioxide. Installation of a plant at Port Pirie based on this process is being evaluated by BRAS.

Jan 1, 1984

The history of the discovery. and successful development of the offshore Gippsland Basin oil and gas fields has been well docu- mented in contemporarary and more recent industry and profes- sional literature. The various articles, papers and books record fairly balanced views and comments as to the nature and results of the explora- tion effort, and factual data concerning the subsequent develop- ment of the fields and facilities concerned with petroleum production in the Bass Strait and Gippsland environment. Recommended reading for those interested in the scientific and technical aspects of the Gippsland Basin developments and the search for petroleum in the Bass and Alway Basins includes the available library contained in the publications of The Australasian Institute of Mining & Metallurgy The Commonwealth Mining Congres since 1960 The Australian Petroleum Exploration Association The Geological Society of Australia The American Association of Petroleum Geologists Various Commonwealth and Victorian Government instrumentalities Trade Journals

Jan 1, 1988

A short study showing how first dry fill and later hydraulic sand fill has allowed mining to continue immediately adjacent to worked out areas in a mine 75 years old. This paper is a case study of filling in an old mine where for 30 years filling was not important until ground troubles were experienced after a series of parallel shrink stopes were pulled empty., Dry fill was distributed from the surface via a system of passes and conveyor belts. With the stabilization of the ground it then became possible to continue mining beside and above the old stopes using totally sealed and decanted hydraulic sand fill. A brief description of the dry fill is given and then more technical details of the hydraulic fill. The necessity for a well trained and experienced hydraulic fill crew is discussed along with the problems of filling small stopes in broken ground.

Jan 1, 1973

By Collier D

The topaz resource at Torrington in northern N.S.W is currently the subject of a joint research and development programme managed by Pacific Copper Ltd, This programme has culminated in a pilot topaz calcination plant, located at Parramatta, which, through its operation, will establish the commercial viability of developing this mineral as an industrial raw material for both the refractory and fluoride chemical industries.

Jan 1, 1989

By P Wollants, B Blanpain, R Ding

Vacuum oxygen decarburisation (VOD) is the refining process used by ALZ (Genk, Belgium) for their production of stainless steels. The process consists of three stages: oxygen blowing at a pressure of 100 mbar, degassing, and reduction of the slag with ferrosilicon at 5 mbar. The magnesia-chromite bricks used in the slag zone of the ladles suffer from acute wear. In this paper results obtained from a program to improve the refractory life span are presented. The dominant wear phenomena were identified with an electron microscopy study of bricks taken from different locations in the ladle. Concurrently a dynamic model for the vacuum oxygen decarburisation (VOD) refining process was developed. The model calculates the elementsÆ oxidation rate during the blowing oxygen stage and allows the continuous calculation of the change of the metal, slag and gas composition throughout the VOD process. From these activities a general scheme of the refractory wear was worked out and measures to improve the refractory life were proposed and implemented.

Jan 1, 2000

The relative importance of magmatic and metamorphic fluids in Archaean gold mineralisation has long been a subject of debate. Computer simulations can be used to explore the interaction between competing fluid flow drivers, thus providing insight into their role in mineralisation. This approach has been applied to Archaean gold mineralisation in the Yilgarn craton, Western Australia. A simple model representing regional metamorphism in a granite-greenstone terrane indicates that fluid produced during a regional metamorphic event in the Yilgarn was unlikely to have been involved in mineralisation, because it would have escaped from the crust long before the main gold event. Another model illustrates the competition between magmatic fluid production, convection, and deformation. The model shows that the timing of deformation relative to fluid production is important in determining the fate of magmatic and metamorphic fluids, and hence their potential to play a role in mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

Low-grade manganese ore from Sandur, India containing 28.2 per cent manganese and 20.9 per cent iron was roasted with sulphating agents, viz ammonium sulphate and sulphuric acid. The effects of temperature of roasting (300 - 800°C), time (15 - 120 minutes) and amount of sulphating agent (0.5 to 2.5 times stoichiometric amount) were studied. Under optimum conditions, it was possible to extract 92 per cent manganese with 0.5 per cent iron at a temperature of 700°C for 90 minutes duration with stoichiometric ammonium sulphate. Further increase in quantity of ammonium sulphate has marginal effect on manganese extraction.Similar studies were carried out with sulphuric acid, and an extraction of about 87 per cent manganese with similar iron contamination was achieved at a temperature of 700°C for 60 minutes duration with stoichiometric quantity of the reagent. Selective extraction of manganese with respect to iron is discussed.

Jan 1, 1996