Search Documents

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

Mond gas-producer tar, and, in fact, all tars obtained from the retorting of coal where steam and air are admitted to the retort, are of entirely different chemical composition to the ordinary coal tar made in the gas or coke works. These tars contain none of, the aromatic hydrocarbons - benzene, toluene, naphthalene, and anthracene, sought after by the ordinary coal-tar refiner.The distillation of Mond tar shows it to consist of phenols of high molecular weight, unsaturated hydrocarbons of high gravity and low viscosity, paraffin wax, and resinous substances of whose composition little is known.The physical properties of Mond producer tar are also peculiar. It has a "short," granular texture when cold, which might be likened to candied honey. It "dries" (hardens) when exposed in thin layers to the air, and, for a coal tar, it cannot be considered sticky. This latterò property, combined with the short texture, prevents its being used successfully for road-making or macadamizing.The drying properties and the paraffin wax contained in: this tar cause it to hold up large percentages of water, probably in the form of emulsion. When containing as much as 10% to 15% moisture it appears to be quite dry.

Jan 1, 1918

By A Olshina, C Willman, D Moore

GeoScience Victoria has completed quantitative assessments of undiscovered gold endowment in the northern parts of the Bendigo and Stawell Zones. The under cover area in the Bendigo Zone (10 000 km2) is likely to contain approximately 1000 t and at least 290 t of gold in undiscovered mesozonal orogenic gold deposits. For the under cover area in the Stawell Zone (30 000 km2), the estimates are approximately 1200 t and at least 200 t of undiscovered mesozonal orogenic gold. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Collins BJ

Basic principles of stack injection are outlined and supported by calculations of thermal, chemical and aerodynamic requirements of an ideal 4000 tpd furnace. Calculated results show that these requirements vary with conversion of FeO, and that best performance may be expected with XFeO = 1.0 for which calculated production is 6919 tpd and coke rate is only 211 kg/thm. Calculations are also presented for a cycled injection. Discussions show that stack injection is a good way of overcoming softening problems and meeting the demand for iron in a fluctuating demand situation when it exceeds the maximum capacity of a furnace.

Jan 1, 1975

Just as Australia is part of the Pacific Rim, so the Pacific Rim should be viewed as part of the whole world. That applies in particular to that scarce commodity û money. There are five main factors of production in any mining development û mineralisation, materials, manpower, management and money. LetÆs focus on the upstream input û mineralisation, and the downstream input û money, especially in the area of communications. Unknown to many, the Competent Person reporting on Mineral Resources and Mineral Reserves has a direct and unavoidable impact on the companyÆs financial statements û the profit and loss account and balance sheet. With respect to reporting of the major asset of most mining companies û the resources/reserves û investors are getting a better deal now than at any time in memory as regards flow and adequacy of information. Australia has been a world leader in this regard. The outlook is for even more informative and useful reporting. The more rigorous reporting requirements for Exploration Results and Mineral Resources/Reserves, which have become a worldwide phenomenon over the last five years, will continue. This will be positive for the mining industry as a whole and for Australia in particular. However competition for the scarce investment dollar will also increase. Put simply, mining has many competitors, unconnected with mining, for the capture of the investment dollar. It behoves all participants to recognise that there are three investment factors which influence strongly the willingness of investors to put money into mining. These are Confidence, Credibility and Consistency. AustraliaÆs investment image stands high in these three respects, but the competition will continue to grow. AustraliaÆs lead must be maintained. However, some investment decisions should not necessarily be based on fundamental, quantifiable facors. Some of these are outlined.

Jan 1, 2004

The recent trend of installing flotation cells with volumes as large as 200 m3 in concentrators is driven mainly by economic considerations such as lower capital, operating and maintenance costs. Despite the economic advantages, the metallurgical benefits from these large cells have not yet been fully realised by the industry. This is mainly due to the lack of understanding of cell operation, viz cell mixing and hydrodynamics, gas dispersion and froth transportation behaviour in large cells. There is still no rational basis for selecting optimum cell operating conditions and down-the-bank operating profiles. The relationship between cell operating conditions and metallurgy is not well established. This has resulted in poor utilisation of cell capacity in many operations. The present trend of installation of fewer cells in a bank requires each cell to be operated very efficiently. Optimisation of cell operation provides an opportunity for significant metallurgical improvements in a flotation circuit with minimal capital expenditure. Extensive work on optimising of cell performance has been carried out at various Teck Cominco operations in Canada, Peru and USA. Three different levels were involved in this work. The first level was aimed at identification of cell operating conditions for optimum mixing and hydrodynamics, gas dispersion, entrainment and froth flow behaviour in individual cells. The objective of the second level was to identify the optimum bank operating profile for cells down the bank in a circuit. The third level then focused on controlling these cell operating conditions and bank operating profiles for tighter control of concentrate grade and recovery for optimum bank metallurgy. This paper presents some of the major findings at all three levels and demonstrates the importance of each level in optimising the performance of flotation banks installed with large cells.

Jan 1, 2005

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

The reasons for using SFRS, including the way a SFRS performs in comparison to plain shotcrete as a support element in mining tunnels, are discussed. The mechanisms by which steel fibres reinforce shotcrete and the need for specifying performance criteria are highlighted. A description of current testing procedures, including an overview of æquantitativeÆ design recommendations provided from various international authorities, is provided. A summary of international recommendations on suitable æqualitativeÆ performance classifications is also reviewed, including a critique of their suitability. Finally recommendations on the practical considerations necessary to ensure good quality, in-place SFRS, are made, including a calculation method for determining minimum steel fibre dosages.

Jan 1, 1999

I wish that in addition to being a Pro- fessional Engineer I was also a communications expert. My principal task this morning, and yours after this meeting, is to convince a wide variety of individuals that steel industry slags are a high quality material that can be used for many purposes; and that their use can significantly alleviate some of the problems facing engineers, public officials, and the general public in our countries. By actual in- place performance over a long period of time steel industry blast furnace slags have proven that they are as good as the best natural aggregates, and better than some, for any type of construction or purpose for which natural aggregates are used. Steel furnace slags have many unique favorable characteristics and prop- erties when compared to other types of aggre- gate even though they cannot be used for all types of construction. We have the facts, all we have to do is present them to the right people in the proper manner.

Jan 1, 1979

By Arndt MB, Bamberg S

The evaluation of risk is becoming more important in the siting of mining operations in the United States as well as the rest of the world. The determination of environmental, economic, as well as health and safety risks is an important step in the planning of any mining operation. Hydrogeology plays an important role in pre-mine planning and in the determination of these risks. The mine operators must determine if ground water would inhibit mining in any way. Factors which are important to consider include mine dewatering economics, slope stability, and other adverse hydrologic impacts. This paper presents methodologies for the characterization of hydrogeological risks for a mining operation. First of all, the term risk analysis is defined and its utility is addressed. Then, stepwise methods for performing a typical risk analysis are presented. Finally, the application of risk analysis to hydrogeology in mining is given. With slight modification, it is believed that these methodologies can be used to evaluate the hydrogeological risks for any mining operation.

Jan 1, 1988

By H Ş. Duzgun

It is expected that the future of mines will heavily adopt autonomy. However, problems with leveraging workforce transition, meeting Sustainable Development Goals, SDG’s (poverty, reduced inequalities), managing uncertainties (geologic, operational, economic), cybersecurity (connectivity, cyber-physical infrastructure) and innovation (transformative processes, real-time decision-making etc) are required to be solved for the intended autonomy. These problems also impact the safety of the future mine environment. The AI technologies provide a broad range of opportunities for enhancing mine safety. However, development of an accurate AI model for mine safety requires a large number of data, which may not be readily available to overcome the associated uncertainties in the mine environment.

May 5, 2022

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

By Wadsley MW

This paper gives an overall view of the CSIRO-SGTE computer system for thermodynamic calculations. The basis of the system is the coupling of a large self-consistent numeric data bank of thermodynamic information to a modular set of application programs. These seven programs cover management of data files, calculation of thermodynamic properties for species and reactions, plotting of predomin- ance area diagrams, equilibrium and enthalpy balances for complex processes, analysis of thermodynamic efficiency and the estimation of unknown properties. The data bank contains a wide coverage of species and data types so that the system may be applied to many areas of chemistry and metallurgy.

Jan 1, 1984

By E Drueppel, M Mistry, J Pateiro

As mining undoubtedly influences the natural environment future challenges of copper ore mining are minimisation of land use in area and duration, proper land rehabilitation as well as tailings management. One possible solution to avoid these negative impacts could be the application of underground mining with backfilling tailings compounds. This approach would definitely increase the production cost. Against this background the project analyses the influence of an æecologically satisfyingÆ copper ore mining on world market prize and demand as well as on the environment. In the project 261 copper ore mines accounting for 98 per cent of world copper production have been examined. After modelling a backfill plant, analyses of applied backfill techniques were conducted. Afterwards a method of cost estimation was developed and then the backfill plant model was applied in three case studies. The results were transferred into scenarios. The work closes with a short discussion and gives an outlook to forthcoming research. The results presented in this work have been generated within the Collaborative Research Center (CRC) 525 entitled æResource-orientated view of metallic raw material flowsÆ. This interdisciplinary project was established at Aachen University of Technology (Germany) in 1997 and is funded by the Deutsche Forschungsgemeinschaft (DFG). The long-term goal of this research program is the identification of options for the resource-sensitive supply and processing of metallic raw materials. In order to address the sustainable development challenges facing the metals and minerals industry an integrated resource management system is to be developed and tested for important metallic raw materials. Case studies for aluminium and copper are being conducted by the CRC 525 in order to provide useful and efficient tools for decision makers over the entire life cycle of these materials.

Jan 1, 2003

There are many different challenges when sampling mineral commodities. Sampling is part of many decision-making processes, from control of the number of drops of a reagent to all aspects involved in determining how much to pay for a mineral consignment. However, if all decisions must be supported by correct assumptions, or at least agreed terms, how can this be guaranteed? The main approach is to emphasise the importance of continuous surveying of sampling practices. If they are based on non-recommended protocols, this raises concerns. In addition, safety failures and lack of appropriate behaviour from the technical perspective can lead to disasters, both from the human and business perspectives. Impacts on safety and health are clearly unacceptable. It should be noted that imperfect safety and health practices in sampling operations have a strange correlation with incorrect sampling techniques. The commercial interface can also be affected. Companies have studied extensively the various aspects of measuring quality parameters for mineral commodities to understand the risks for investors and owners, and they take decisions that fundamentally respect the interests of parties in contracts and not result in losses. Every result should be obtained in defensible ways, and neither losses nor profits taken in indefensible ways. Most of such situations are related to bias; a significant systematic difference between a measured value and a reference value for a contractual quality parameter. Bias is always undesirable, because it always implies an incorrect advantage for one party and without doubt an undesired disadvantage for the other party. These situations are solved financially through a third-party arbitrator becoming involved in delicate situations, such as a commercial claim, but the outcome is always tangibly or intangibly bad for one of the parties. Another possibility is a permanent or temporary loss of precision. Poor precision, due its nature, generates reasonably balanced losses and profits, but it may hide out-of-control situations, generate instability and induce financial losses due to actions taken towards clearing commercial disputes involving interlaboratory programs, sample exchanges and duplicated sampling and sample preparation procedures, in the end wasting time and resources and creating a permanent source of commercial tension. While bias situations demand immediate adjustments for correctness, poor precision has to be understood as something that cannot be just calibrated out and is a situation that demands investment of time and effort. Precision optimisation has to take into account best practice for obtaining the required precision as well as cost/benefit analysis studies. Purchasers, engineers, salesmen and all personnel need to recognise that sampling is a major area to understand when taking decisions. The aim is to spread concepts that can really help, such as simple in-house actions to improve productivity and completion of surveys on commercial sampling operations, in order to ensure correct results are obtained and assertively take corrective actions, thereby establishing a healthy relationship with investors, suppliers and purchasers and in the process optimising the business.

Jan 1, 2008

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

By H Durrant, P I. Corke, J Cunningham

This paper reviews the state-of-the-art in the automation of underground mining vehicles and reports on the development of an autonomous navigation system under development through the CMTE with sponsorship arranged by AMIRA. Past attempts at automating LHDs and haul trucks are described and their particular strengths and weaknesses are discussed. The auto-guidance system being developed overcomes some of the limitations of state-of-the-art prototype æcommercialÆ systems. It can be retrofitted to existing remote controlled vehicles, uses minimum installed infrastructure and is flexible enough for rapid relocation to alternate routes. The navigation techniques use data fusion of two separate sets of sensors combining natural feature recognition, nodal maps and inertial navigation techniques. Collision detection is incorporated and people and other traffic are excluded from the tramming area. This paper describes the work being done by the group with regard to auto-tramming and also outlines the future goals.

Jan 1, 1998

By S A. Ravishankar

An overview of flotation reagents used in sulfide and non-sulfide separations, from an industrial perspective, is given in this presentation to highlight the current applications knowledge. The historical and theoretical aspects, which are well documented in numerous books and reviews, will only be highlighted, when necessary, to support the theme of this paper, viz critical analysis of reagent research, design, selection and optimisation with an emphasis on relevance to plant needs and practice. The three types of flotation reagents; viz collectors, frothers and modifiers, used currently in the industry are briefly reviewed; pitfalls and gaps, arising from somewhat arbitrary and reductionistic practice in reagent applications, are identified; and the impact of environmental regulations on current and future reagent development is discussed. The importance of frothers and modifiers, which have received less overall attention than collectors, is highlighted. The need for a rational, holistic (or ætotal systemÆ, ætop-downÆ) approach for reagent design, selection and optimisation is discussed with a view to provide remedies for pitfalls and a platform for filling gaps in reagent chemistry and applications, and to develop reagent technology that can deliver robust solutions to plant needs. Flotation Matrix 100TM, a comprehensive package designed at Cytec to incorporate all the elements of the holistic approach û viz definition of mineralogy and plant needs, rule-based expert system rational reagent selection, and laboratory and plant best practices û will also be described.No paper available for this abstract

Jan 1, 2005

Mining Automation By Professor Hugh Durrant-Whyte, Australian Centre for Field Robotics and Centre for Mining Technology and Equipment, Department of Mechanical and Mechatronic Engineering, The University of Sydney Professor Hugh Durrant-Whyte summarised why the mining industry needs to automate and reviewed the current automation technology - its risks, costs and benefits. Why automate? The drivers for automation include: safety, productivity, quality control and reduced manning, equipment utilisation, maintenance, and organisation and planning. Durrant-Whyte recommended starting out with a picture of a fully automated mine and working backwards through a systematic analysis of benefit and risk. This also involves looking at the impact of the total automation on current mine design, and identifying the key technologies.

Jan 1, 1997