Search Documents

By Keast-Jones R

The relative merits of treating coal by flotation and spiral concentrators have been examined by tests on run-of-plant fines samples from three seams in the Wittingham coal measures of the Upper Hunter Valley. Flotation of the complete fines was found to be the most metallurgically efficient process with yields substantially superior to those obtained from treatment of only the deslimed fines. A strict comparison between spirals and flotation for the treatment of the deslimed fines was impossible due to differences in product quality. However, the results indicated that the performance of a flotation circuit would be equivalent, and sometimes superior, to that of a spiral circuit.

Jan 1, 1984

By Brenchley R

Partitioning behaviour studies for -particles in the 250 to 1,000 micron size range at. the Curragh coal preparation plant are presented. Plant surveys were conducted to compare the partitioning efficiencies of dense medium cyclones and froth flotation. The aim was to assess the potential for improving yield of coal by directing more of the top size of flotation feed material to dense medium cyclones. ovel mass balancing and model fitting NI procedures were used. While flotation offers high yield of low ash particles smaller than 500 microns, dense medium cyclone rejection .of high ash particles larger than 250 microns is superior. These strengths of the two processes are turned to good advantage by the use or desliming sieve bends which tend to perform some density separation on the'size fractions of interest, directing lower ash material to froth flotation than to the dense medium cyclones.

Jan 1, 1987

A laboratory investigation was carried out to obtain data on the explosive character- istics of selected coals mined in New South Wales. Seven coal seams were sampled and the volatile matter content of the coals tested varied between 28 and 37 percent. A mod- ified Hartmann apparatus with a volume of 1250 ml was used in the investigation. Dust clou' generation was produced by an air blast delivered radially through a mushroom type valve and the ignition source was a-continuous A.C. spark produced by a 20 000 V, 50 mA transformer. The coal dust parameters invest- igated were the maximum pressure developed, the average and maximum rates of pressure rise at dust concentrations between 200 and 1500 3 g/m.

Jan 1, 1981

In the last eight years inclined conveyor haulage systems have established themselves in the mainstream for hard rock underground mine haulage. This leaves the question; what else might be on the horizon for mine haulage and how do we address the process of selecting haulage systems for new mines? This paper considers the identification of viable haulage technologies for underground mines and explores an approach for assessing existing and potential technologies. The example of a large deep mine is considered here. The evaluation of existing haulage systems relies on precedence and the assessment of the system capacity to meet the haulage requirements envisaged for a particular mining project. The assessment of potential technologies for mine haulage relies on the capacity to deliver a viable production-scale system within the timeline envisaged for developing a mining project. The haulage technologies addressed in this paper include: shaft hoisting,conveyor haulage,truck haulage,vertical conveyors, andhydraulic hoisting. This paper does not consider rail haulage out of a mine. This is simply because Australian topography typically has insufficient relief to bring them into consideration. However, rail haulage is a widely used and effective haulage solution in situations where significant topographical relief is present. The assessment of haulage system capability focuses on the following fundamental questions: How reliable are they? What is the degree of technical risk in a business context?What levels of flexibility do they offer?How capital effective are they? What returns are indicated by the balance of capital and operating cost estimates?

Jan 1, 2008

Optimising a mining or a quarrying operation about the overall cost is quite a challenge as there never is a situation where we have exactly the same conditions regarding rock properties, explosives' performance, mining equipment or evironmental restrictions. The amount of endless influencing parameters and variables make the evaluation process difficult. The enormous progress we have seen during the recent two decades in computing has however significantly increased our ability to evaluate and process the information gathered, and refine our existing prediction models. Refined models demand an increasing volume of good quality information to show reliable conformity with reality. There is a great need for co-operative work in the mining and quarrying society if we shall be able to screen all available data, systematically find the key-parameters influencing the results and to build robust scientific models. No organisations today have all the skilled people needed or can afford to hire the necessary specialists in all the overlapping branches. This paper highlights some on-going work where the Dyno Explosives Group is adding some new pieces to the giant jigsaw puzzle representing the ultimate model of the mining and quarrying operations we all of this society would like to see completed.

Jan 1, 1995

In a previous study, various pyrite depressants were examined to improve the flotation performance of a copper-sulfide ore. Optimal results from this study were used to examine the effect of elevation on recovery and grade. Tests were conducted at elevations of 3350, 1735, 610 and -760 metres, consisted of five repetitive experiments for statistical analysis, and were performed both with and without airflow control. Tests were also performed in a glove box at Montana Tech to mimic the pressure conditions. Results indicate that both recovery and grade are dependent on pressure via bubble size and airflow suggesting that pressurised flotation cells should be considered for operations, particularly those at high elevation. Economics are extremely favourable for implementation because ensuing capital expenses are inconsequential with minimal time for return-on-investment.

Jan 1, 2005

This paper deals with a few aspects of town planning and town management which affect human relationships within that town. Its scope is limited to the consideration of towns forming an adjunct to a mining operation, and particularly considers these aspects at the Hamersley Iron Pty. Limited, town of Parabur doo, Western Australia. Planning and standards of a new town and amenities are-discussed and related through living comfort to an effect on human relation- ships. Town administration and the promotion of many forms of social activities are dealt with in detail to illustrate the importance of quickly forming a cohesive community from a large number of newly arriving individuals. The results achieved by the planning and administration at Paraburdoo are highlighted by involving many residents by way of answers to a questionnaire.

Jan 1, 1973

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

By Keys NJ

The so-called COMAT process provides a method for leaching low grade sulphide mattes in an acidic ferric sulphate medium in such a way that non ferrous base metals such as Ni,Cu and Co are substantially all dissolved; the concentration of residual acid and dissolved iron remaining in the leaching solution is low, and a large portion of the sulphide sulphur is converted to elemental sulphur. Thus the quantity of neutralising agents required to remove residual acid and dissolved iron from the leach solution prior to subsequent recovery of the dissolved base metals is greatly reduced. The leach residue and iron precip- itate report in a readily filterable form. In this paper results obtained on a pilot plant scale are presented for the leaching of a typical low grade matte in the manner describ- ed above; for the solvent extraction and elec- trowinning of copper, and for the removal of residual acid, copper and iron from the copper solvent extraction raffinate. Processes tested on a laboratory scale for the further recovery of cobalt and nickel by solvent extraction and electrowinning, and for the recovery of sulphuric acid and ammonium hydr- oxide from the dissolved ammonium sulphate salt contained in the final plant effluent, are also briefly described.

Jan 1, 1986

Gallery Stoping, an old but little used stoping method, has been reintroduced to workings at the Paringa South Shaft.Orebodies which are amenable to such a method are being mined in this manner with considerable advantages and savings.The advantages of gallery stoping as used at Paringa, compared with traditional mining methods are:1. constant cash flow2. low set up cost and initial stope development3. nearly 1005 recovery 4. no access problems 5. quicker tonnagesAs compared with highly mechanized mining methods, it has been found to be slower but requires less development, gives improved grade control, has less impact on the surrounding rock and fragmentation is much better, reducing secondary blasting costs.This paper examines the mining method and illustrates the advantages of gallery stoping at Paringa.

Jan 1, 1985

By McQuade CV, Riley SJ

Acid mine drainage is an unavoidable consequence of some coal mining operations. Typically runoff pH is below 3.5 and at these pH levels heavy metals are mobilised. Leachate from coal reject dumps may require collection and treatment to raise the pH and precipitate the metals before being discharged.A bi-product of coal mining operations at Clarence Colliery is coarse washery reject. At present the coarse reject is deposited above ground and rehabilitated. Adjacent to Clarence Colliery is the Kable's Transport Pty Ltd sand mining operation. It has been proposed that co-disposal of the rejects from both operations may produce a product whose leachate has near neutral pH.

Jan 1, 1998

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

By Crawford J

The paper asks the question 'Why Limit the HYDROTRANSPORT of material to the confines of your washplant'.A brief historical review of widely accepted slurry transport operation establishes that we are not talking about new technology - simply applying proven experience to an innovative continuous system.The paper reviews a simple potential application and compares capital and operating costs with conventional trucking.No attempt has been made to develop a complete mine plan and the comparison has been limited to material transport costs.

Jan 1, 1992

By Eupene GS

The valuation of exploration properties which contain no identified resources or reserves is the most subjective of all valuation tasks likely to be carried out by a geologist. The geoscience rating method proposed by Kilburn (1990) recognises this inherent subjectivity but also attempts to apply some discipline to the valuation process. Some other methods used for valuations of this type clearly lack discipline and are open to misuse and abuse. The Kilburn method essentially requires the practitioner to justify all aspects of the valuation process. The valuer must specify and, more importantly, quantify aspects which enhance or downgrade the intrinsic value of each property. The intrinsic value is called the ""base acquisition cost"" (BAC) and it represents the average cost to identify, apply for and retain a base unit of area of title. The BAC and base unit of area both vary with different types of exploration and mining title but remain constant for similar types of titles in the same mineral tenure regime. In the Kilburn Method the enhancement/ downgrading factors are determined by the geotechnical prospectivity (Kilburn Method) within the title. A modified version of the Kilburn Method presented here (""Modified Kilburn Method"") also focuses attention on other real variables besides the geotechnical attributes which influence valuations of this type, viz., competition for tenure and activity in the markets in which the exploration properties are being traded. The most active such market at present is the stock market. By utilising uniform BACs and base units of area (for similar titles) for all exploration properties (in practice in Australia this is only possible within a particular State or Territory), the method exposes the valuer's opinions of each of these variables to the scrutiny of the investor. The investor (or his professional adviser) is afforded the opportunity to directly compare valuations on different properties by different practitioners and can assess how the final valuation is weighted in respect of geotechnical prospectivity, competition for tenure, and stock/financial market sentiment. No other method currently employed in Australia to value mineral exploration properties affords the investor this `luxury', which some may argue is their right.

Jan 1, 1994

The major technological advances of the last 30 years have profoundly reshaped mining practices. Machines keep getting bigger while productivity continues to increase and manning levels drop. These trends will continue and the introduction of breakthrough technologies will continue to accelerate, driven by a continued focus on lowering the cost of production, improving the productivity of workers and machines, and ensuring safer working environments. At the same time, global consolidation of mining companies has impacted on technology development in a range of ways. There are many potential technologies being proposed, some already operating in Australian mines. The automation of underground load-haul-dump (LHD) trucks for example, continues the process of removing workers from the most dangerous operating environments. Global positioning systems fitted to draglines, fibre optic communication channels, and 400 tonne trucks are only some examples of what lies ahead. However, where we need to return focus is to the technology of management û which is also one of the two key interrelated themes of this keynote address. Have we, as an industry, adequately been able to keep up with technological advances? Are our management systems as competent as the machinery we employ? The other key theme is the processes of globalisation and consolidation. What are the impacts on our industry? What are the implications of these processes, particularly for the ways in which we manage our people? My paper is divided into several components:some comments on the coal industry and the dramatic restructuring we have seen in recent years; in the context of this restructuring, an overview of my company and its evolution; my views on the role of contractors; some comments on the consolidation also occurring in the mining machinery and equipment, technology and services sectors; some observations on two major areas of technology û drill and blast; and trucks, shovels and excavators; the implications of consolidation and new technology for our employees and management; and finally some comments on research programs.

Jan 1, 2001

One of the often overlooked factors affecting the capital investment decision in new or existing plants is the value of stock holdings necessary to maintain the plant. This paper puts forward a simple decision matrix on whether a part should be stocked depending on 1. the criticality of the item of equipment in terms of the effect on cash flow of its failure, 2. the lead time of the part, and 3. the stock holding value if it were Stocked.

Jan 1, 1986

Multiple regression analysis applied to ventilation records of stopes on the Witwatersrand showed that it was possible to estimate the temperature increase per 100 ft for a new stope with a standard deviation of 0' 5°F. The analysis also threw light on the relative effect on this estimate of five different factors.Application of the analysis of variance technique to a factorialexperiment on the production of dust during rock drilling showed that the effects of air and water pressure were quite small but also showed that the between-machine variation was unexpectedly large.Analysis of variance also proved a valuable means for assessing the bias and random error variation of aneroid barometers used in pressure surveys.INTRODUCTIONThree examples are discussed to illustrate the use of the techniques of "analysis of variance" and "multiple regression" in research on the ventilation of gold mines. Although the techniques are basically similar their application to each example has a slightly different emphasis and the examples were chosen for this reason. The variation ofemphasis is as follows.1. Temperature increases in stapes. This work was undertaken as a preliminary to possible extensive controlled experimentation (Lambrechts, 1959). Data collected in routine work by the mine ventilation personnel were used for analysis and no specific experiments were carried out. The main object was to see whether such data could provide any strong pointers to factors which might be worthy ofmore careful study and to factors which could initially be ignored. Of course, there was hope that the study might provide an empirical formula for rough forecasts.

Jan 1, 1962

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001

Production scheduling is an important element of the mine planning process. The production schedule specifies the quantities of mineral to extract, the source of this ore, the timing of extraction and, where necessary, the quantity and timing of backfill placement. These details are important in linking long-term strategic goals to short-term operational planning. Mine scheduling techniques form the basis for communicating information concerning the overall impact of design and planning changes to a wide range of people at many levels within an organisation. Consequently the techniques used for mine scheduling must support the decision-making process by consistently providing high quality schedules in response to revised and updated data. A new mixed integer programming (MIP) model has been developed to generate optimal production schedules for underground stoping operations. The model maximised the before-tax Net Present Value of the production schedule while satisfying constraints such as contained metal tonnage, hoisting capacity, stope geometry relationships and stope backfilling demands. Zero-one variables were used to represent the decision to extract or backfill each stope in a particular time period. Continuous variables, capable of having non-integer values, were used to denote the quantity of ore or backfill associated with a specific stope in a given time period. A case study is presented to demonstrate the significant improvement in before-tax NPV over a comparative manual production schedule in a large underground mine. The MIP model allows for further modification to reduce solution times and meet the needs of individual mines.

Jan 1, 1995