Search Documents

By E S. Bernard

Toughness testing of fibre reinforced concrete (FRC) at 28 days age is typically undertaken as part of quality control for the many applications where fibres are used in concrete, including shotcrete, tunnel segments, and cast-in-place tunnel linings. The performance achieved at 28 days is usually assumed to be retained with increasing age. However, as the average strength grade of concrete used in most tunnelling applications, including tunnel segments, has steadily increased over the last 20 years, this assumption is becoming increasingly unviable. This is because for some types of fibre the mode of post-crack fibre behaviour depends on the strength of the concrete and can change from a desirable high-energy pull-out mode to a low-energy rupture mode as the strength and age of concrete increases. This paper describes a series of trials performed over two years in which the American Society for Testing and Materials (ASTM) C1609/C1609M beam tests were used to assess the performance of FRC reinforced with two widely used brands of steel and macro-synthetic fibre. The hooked-end steel fibres used for half the beams exhibited a dramatic fall in performance beyond 56 days age as the mode of failure changed from pull-out to rupture. The other fibre did not exhibit a fall in performance with age. This phenomenon highlights the need to quantify performance of FRC at much later ages when long-term performance is required, for example, to resist seismic events or changes in ground stress due to nearby excavations. As an alternative, a reduction factor may be applied to the performance of FRC mixes for which evidence of satisfactory long-term performance is not?available.CITATION:Bernard, E S, 2014. Age-dependent changes in post-cracking performance of fibre-reinforced concrete for tunnel?segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By R Moller

Reconciliation at large iron ore operations is a complex and time- consuming process. Often the volume of data and the large range of different stakeholders makes the process almost impossible. Up until recently geologists and engineers at these operations would spend hours cutting and pasting data in and out of monster spreadsheets, diligently comparing how resource/reserve models, grade control and survey pick-ups compare to what was actually produced. In 2003 the Sishen Iron Ore Mine in South Africa broke this cycle by implementing SnowdenÆs Reconcilor software. The implementation of a dedicated reconciliation system required a number of existing practices to be changed, with the involvement of stakeholders right across the mine. Data sources had to be clarified and validated, terminology had to be standardised, processes needed to be documented and some methodologies needed to be updated. This was a task that required significant effort by Kumba personnel so that the system could be successfully implemented. This paper provides a case study of the reconciliation system implementation at Sishen. It is a story of an operation that evolved from using a number of fragmented reconciliation processes to using a unified automated system. This paper outlines the key estimates and measurements that are used for reconciliation, details the characteristics of an automated web-based information management system to facilitate the process and provides some insights about the benefits that have been gained though the use of a rigorous reconciliation process.

Jan 1, 2005

By G Zhang, I Glacken

Multiple indicator kriging (MIK) has been used in the minerals industry for some decades. As one of the non-linear estimation methodologies, MIK has advantages related to resolving multiple or mixed populations, high variability data and strongly skewed distributions. Applying the MIK methodology requires a lot more effort when compared to other non-linear methodologies, for example localised uniform conditioning. This is due not only to the variogram modelling for multiple indicators, but the validation is also very important because the panel model is fundamental for follow-up work, including the generation of recoverable resources at the local or SMU scale. Apart from this, only a few reported case studies of MIK have documented post-processing of the estimated modelled distribution, representing the probability distribution at point scale at un-sampled locations. The MIK post processing should include the change of support from the point scale to the panel scale, and then the extraction of quantile values from the panel conditional cumulative distribution function (CCDF) for localisation of grades into the SMUs within each panel, based on a ranking estimate marking the SMUs from high to low. In this paper, we present a case study on a gold deposit with the MIK method with full-post processing implemented for recoverable resources. The MIK point estimate was carried out with an indirect lognormal change of support from point to panel scale, and localisation was done with a custom script. The localised uniform conditioning (LUC) method was also applied for comparison purposes. The comparison shows that MIK has advantages compared to LUC when comes to capturing the high-grades, especially when mixed or varying anisotropy is present within the mineralisation.

May 24, 2023

In late 1987 it was recognised that column flotation might have potential for improving the grade of the zinc concentrate produced at Pasminco's South Mine in Broken Hill. Intermittent test work was carried out during 1988 using a 90 mm diameter by 6 m high perspex column, built and initially operated by staff from CRA Advanced Technical Development. This column was found to have insufficient retention time so, during the first half of 1989, Pasminco constructed and installed a 200 mm diameter unit of the same height. Extensive testwork was carried out using this column during the latter half of 1989 and early 1990. It was clear from the results that a grade improvement of between 1 and 2 per cent (absolute) would be achievable. The effect of column cleaning on overall recovery was not established with the same degree of confidence, so the proposed new circuit is to include one of the existing banks of OK8 cleaner cells as a scavenger on column tailings. The test work provided sufficient data for preliminary design work to begin in May 1990 and commissioning of full scale zinc cleaner columns is planned for mid 1991. This paper summarizes the results and describes some of the experiences with column flotation at the Pasminco South Mine.

Jan 1, 1991

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023

Valuers will often intuitively express the probability that property value will exceed a certain amount . . . 'I think the chances that the value will exceed $50 million are excellent. The chances that they will exceed $80 million are poor'. This paper shows how it is possible to combine the uncertainties of the value of several key items to provide an estimate of the probability of a certain overall value being achieved. The valuation of a large copper/gold deposit was naturally influenced by uncertainties in the base assumptions of costs and metal prices. Potential acquisition of the property through share purchase raised the issue of what was a reasonable intrinsic value for the shares. Market considerations could be used to appropriately adjust the intrinsic value. After a range of possible metal prices and operating costs were determined, estimates were made of their probable distributions. By combining these probabilities in a random selection, a range of property values was calculated. Each value had its respective probability of occurrence. This allowed a most likely value of shares to be calculated. This paper demonstrates how the valuer's intuition is complemented by numerical analysis.

Jan 1, 1994

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By G Bickert

Australia is currently developing and engineering a range of specialised processing options for rare earth (RE) (Lynas, 2011, Alkane, 2005), zirconia (Alkane, 2005), lithium (Galaxy Resources, 2008) and other special minerals and metals required in high-tech applications. The processing of lithium, zirconium and RE minerals is based on complex leaching processes which require extensive liquor clarification, solid liquid separation and solids washing. The filtration properties for those leach liquors, residues and precipitates are not well understood and differ drastically according to the process route applied. Thus, filtration test work is essential for equipment selection, sizing and design. Similar types of slurries are filtered in laterite nickel, TiO2 and other chemical oriented processes, while more experience is available here as those processes are applied widely for a number of decades. The increasing need for dry stacking of tailings requires advanced tailings filtration with properties differing drastically depending on tailings properties. More traditional mineral processes such as flotation commonly apply filtration. All of these and other cases require proper filtration test work particularly evaluation of vacuum versus pressure filtration and the need for cake pressing and/or air blowing for filter presses. Bench scale test work and/or pilot plant operation is common to determine filtration rates, achievable cake moisture and wash efficiencies and sometimes filtrate clarity. While those values are important, there is much more valid information to be obtained by filtration test work.This paper discusses the intricacy of filter selection and sizing based on driving forces (vacuum and pressure air, compression by mechanical means and slurry) and parameters (cake thickness, forces and times) and different processes utilised in common filtration equipment. It will discuss the in’s and out’s of filtration test work design, planning, and in particular data gathering, processing, reporting, evaluation and filter sizing from recent examples of bench and pilot scale filtration test work for above applications together with methods for predicting filtration performance for example where test work is lacking. One focus will be the realistic extrapolation of test work results towards different parameters utilised in full scale equipment and plants. The conclusion of the paper will contain checklist for filtration test work.

Aug 8, 2011

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

By I Gipps

A vision of what the future mine involves all aspects of mining, ie orebody access, ore stoping, material transport, processing and waste material disposal. This paper examines one aspect of the future mine: rock extraction, stoping, automated for remote operation, high productivity and low cost. Concepts for the future require a re-think of the mining process and ROES® re-examines how bulk stoping of ore can be undertaken and how this should be redesigned to accommodate the possibilities that exists with remote control and automated operations.ROES® is a new mining system for underground mines and quarries utilising a shaft located close to or within the stope for the ore breakage process. The system is designed to exclude personnel from contact with production drilling, explosive placement and detonation so all of these tasks are remotely controlled or automated. Survey of the shaft, stope back and broken rock within the stope will occur, following each blast, by remote control or automated techniques. The survey will include excavation geometry, rock fragmentation, geotechnical characterisation and estimation of ore grade. Blastholes will be surveyed before placement of explosives and, with the survey data, the optimal explosive placement and blast timing will be determined with the best available information.ROES® is designed for application in open stoping or sublevel caving in disseminated, geologically defined, thick tabular or narrow vein ore bodies. Technologies developed for ROES® will also have potential applications to caving operations, reducing the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES® will reduce the stope associated development by half and will allow ore to be brought on-stream sooner and at lower cost. Other savings will flow with the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity.

Nov 22, 2011

By R Berry, S G. Walters, J A. Hunt, D Collett

The texture of an ore type is fundamental in understanding the metallurgical behaviour of an ore. This study will show examples of how quantified textural attributes (mineral shape, grain size and mineral association) can be obtained from automated and scanning electron microscope (SEM)-based microscopy and utilised using advanced image processing techniques. Examples will be shown of integrating quantified and semi-quantified meso- and macro-scale textural attributes as well as how they relate to texture-based visual logging systems. The implications of texture for processing behaviours such as comminution, liberation and recovery will be discussed. This research is part of a major collaborative geometallurgical project undertaken at the Centre of Excellence in Ore Deposits (CODES, University of Tasmania) and the Julius Kruttschnitt Mineral Research Centre (JKMRC, University of Queensland). The authors wish to acknowledge financial support and permission to publish from the sponsors of the AMIRA P843 GEMIII project.

Jan 1, 2008

The report by Baker (1958, p. 27) of krennerite in contact with gold in a specimen from the 2500 ft level, Phantom South lode, Great Boulder mine, Kalgoorlie, led the writer to look into this further, since Cabri (1965) reported that the assemblage krennerite-gold was unstable between 238° and 356° C, and possibly down to room temperature.Dr. G. Baker very generously provided the writer with two chips from the same rock specimen (No. 14 as labelled from the mine) in which the krennerite gold assemblage was reported to occur. These were examined by polished section and x-ray diffraction techniques and returned to the classified collection of the Mineragraphic Investigations Section of CSIRO.One specimen, showing visible gold, was examined optically with a binocular microscope and telluride material was twice removed from contact with the gold for x-ray diffraction. This material proved to be petzite and so amends a statement by Baker (1958, p. 39) that no petzite was found in the Phantom lodes.The second chip was polished, and microscopic...

Jan 1, 1967

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

Traditional methods for the production of transition metals from their ores usually include the electric arc smelting of the ore or concentrate to produce a ferroalloy. This is subsequently refined to produce either a ferroalloy or to produce the metal or metallic carbide. Recent trends in the treatment of iron ores have seen the development of many processes for solid state carbothermic reduction followed by melting of the prereduced iron to produce steel and similar types of processes are under consideration for the production of ferroalloys. There are clear potential savings in energy and control of emissions from such processes. This paper discusses some research which is currently underway at La Trobe University into the solid state carbothermic reduction of chromium and tungsten ores to produce the metallic ferroalloy or the carbide for subsequent further processing. The kinetics of the carbothermic reduction of both chromite and scheelite were found to be dominated by gaseous CO rather than by direct carbon reduction. However the diffusion of carbon into the ore is certainly an important feature of the process. The production of tungsten carbide from the metal is the slow step in tungsten reduction. The development of phases during reduction were studied using a scanning electron microscope and an electron probe and knowledge of the phases produced allows analysis of the reduction process.

Jan 1, 1997