Search Documents

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

Continuous improvement in environmental management assists in the achievement of sustainability goals for the processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. Case studies are presented for a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided.The auditing process as described here for coal mines, and coal handling and preparation plants, is equally applicable to the processing of other mineral ores, metalliferous mines, quarries, and oil and gas projects.

Jan 1, 2004

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By G Sartor, A Rich, D Grimsey, R Forzatti, M White

An in-depth process model was developed for the pyrometallurgical, off-gas systems and water balance of the Kalgoorlie Nickel Smelter. This model was used to assess plant capacity with changing concentrate grades, increased throughput and tighter environmental emissions under a range of potential future operating conditions. Comparison of modelled results allowed for flow sheet optimisation across a range of metrics including sustainability, processing capacity and costs. Process modelling software, METSIM® (ver 2020.06 by METSIM International), was used to simulate the flash furnace, integrated electric slag cleaning furnace, Pierce-Smith converters, matte granulation, waste heat boiler, hot gas handling equipment, wet gas cleaning plant and acid plant. The METSIM® model was divided into three separate, yet interconnected models: metals, off-gas and water balancing. This allowed for improved modelling efficiency and traceability while minimising manual error. The METSIM® model was supported by inputs from other specialised software. Chemical thermodynamics software, FactSage™ (ver 8.2 by GTT Technologies), was used to establish relationships for the flash furnace fluxing strategy and determine the operating temperature. Arena® (ver 16.0 by Rockwell Automation), a discrete event modelling software, was used to simulate material movements within the aisle as well as Pierce-Smith converter operation, allowing for integration with upstream and downstream systems. A dynamic data exchange (DDE) was used to connect the results of each software package, interfacing through Excel® (version 4203 by Microsoft). The integration between models provided a streamlined approach to test capacity, bottlenecks, water consumption and emissions under a range of operating conditions, enabling a more robust process. Further downstream modelling techniques were used to assess mechanical equipment. METSIM® outputs provided key parameters for combustion assessments using computational fluid dynamics and finite element analysis for the furnace mechanical design.

Aug 21, 2024

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By Nickson NM, Lancucki CJ

X-ray diffraction and differential thermal methodshave been used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis has been made of the mineralogy and. particle size distribution of eighteen samples from beds' in two pits in~the Recent seaiinents in the Adelaide plains, of six white clays.: developed from the weathering of the Adelaide series of `sediments and, of ,four -Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products 'in the Adelaide area are manufactured from mixtures of these clays:, so the mineralogy and particle size distribution have been determined of eighteen clay mixtures used to make red bricks, cream bricks,. facing bricks, pipes and tiles. Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.

Jan 1, 1963

Copper refining electrolytes are maintained in the range 60-65¦C to ensure an efficient operation. The heat energy required to meet these temperatures has been traditionally derived from the electrical energy required for the electrolytic process and supplementary steam energy. In 1983, experiments were conducted at Copper Refineries Pty. Ltd. (CRL) to determine the effects of insulating the Tank House cells, and fully covering the cells. The results of these experiments showed conclusively that greatly reduced steam consumption would be required to maintain electrolyte temperatures. These positive results led to an Energy Conservation Programme for the Tank House, and this was implemented in 1984. A computerised cell cover monitoring system was developed, and is used to control cell coverage and fluid balance. The experimental work and the benefits obtained since implementation of the programme are discussed.

Jan 1, 1985

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

It is a sad commentary on human nature that for every successful, unscrupulous entrepreneur you need a multitude of incautious, greedy investors. One wonders whether is will be ever possible to completely protect investors from their reckless gambling instincts, which are so widely encouraged elsewhere in society.

Jan 1, 1989

Draglines have been a significant part of world open cut mining since the early part of the 20th century particularly for the removal of overburden in the strip mining of coal. Since the mid-1960s draglines have played a major part in the large strip mining coal developments of Queensland and New South Wales.There are now over 60 large draglines operating in Australia ranging in size from 23 to 103 cubic metres bucket capacity, with digging depths to 60 metres, dumping heights to 50 metres and dumping radii to 100 metres. The application of these draglines has progressed through the uncovering of coal in shallow, single seam operations to deep multi-seam operations requiring a greater dependence on pre-stripping activities ahead of the dragline to remove overburden not able to be efficiently handled by the dragline.

Jan 1, 1992

Tourmaline-bearing rocks are a rare rock type of Suites 3, 4 and 5 at Broken Hill. Minor laminated plagioclase-quartz-tourmaline rocks occur in association with the quartz- magnetite rocks of Suite 3 with the greatest abundance of tourmaline-bearing rocks present in Suite 4 intimately associated with lode horizon, scheelite mineralisation and zinc mineralistion - all approximate strike equivalents of the Broken Hill Pb-Zn-Ag deposit. Bedded quartz-tourmaline rocks, tourmalinites, tourmaline-rich pelite and tourmaline-bearing lode horizon have been recorded from suite 4. The bedded tourmaline rocks rarely display cross bedding, graded bedding, slump structures and small scale intraformational breccias. Minor tourmaline-gahnite-bearing pelites are present in Suite 5. The sedimentary structures, metamorphic textures, the stratigraphic position of the tourmaline-rocks and the presence of quartz-tourmaline-gahnite-spessartine (-fluorapatite) lode rocks indicates that the mineralisation at Broken Hill and the tourmaline-rich rocks are all products of submarine exhalative hot spring systems which were most active during deposition of Suite 4 rocks. Tourmaline is chemically different from that associated with granitic activity and from other submarine exhalative tourmaline-rich rocks because the premetamorphic alteration at Broken Hill involved addition of Fe, Ti and F and subtraction of Mg - a feature reflected in the chemistry of tourmaline from Broken Hill.

Jan 1, 1983

By M Robertson

3D photogrammetry is a powerful tool for data capture and interpretation, utilised at all Australian underground MMG sites. In personnel constrained mines, 3D photogrammetry can free up personnel time, improve data quality for resource modelling, as well as benefit other mining departments.At Rosebery one of the challenges faced by geologists was no longer data capture but, rather, avoiding paralysis by analysis from the sheer abundance of information currently available to the department. Although the data had been interpreted, the structural model was cluttered; the geological block model was not incorporating any geological domains captured by 3D photogrammetry, nor was it being utilised by other departments such as geotechnical engineering.The geology department is now focusing on utilising all the interpreted data gained from each photograph heading into an uncluttered, easily understandable model for geologists and other mining departments.Our solutions involve integrating the Leapfrog modelling suite into the process, streamlining the structural model, tailoring the data interpretations for future updates of the block model and training other departments to improve utilisation of the interpreted data. This process also uncovered other benefits for near-mine exploration, and improving our understanding of the deposit’s origin.CITATION:Robertson, M, 2017. The practical use of underground 3D photogrammetry data at MMG Rosebery polymetallic mine, Tasmania, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 409–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017