Search Documents

By M Paine

Work to date has shown that the use of Al2O3:SiO2 ratios is suitable for identifying potential gibbsite bearing samples. Subsequent confirmatory XRD analysis helps to refi ne this initial identification. Based on these methods, gibbsite has been mapped in two common settings:1. along steeply dipping faults, or2. in association with stratigraphic contacts where one unit is aluminous (eg dolerite dyke).On a microscale, the samples studied illustrate an association between haematite, and to a lesser extent goethite, and gibbsite. In these samples the dominant forms of haematite are discrete crystalline phases of either microplaty haematite or euhedral martite. Two dominant forms of gibbsite were observed:1. vein style gibbsite that cross-cuts (or infill’s cracks) in goethite ± martite iron oxide associations, or2. gibbsite intimately intergrown with and forming a matrix to microplaty haematite.Some of the gibbsite microstructures observed suggest that it may have formed during a very hydrous, possibly hypogene, stage of the deposit genesis. The presence of this crystalline gibbsite, and in particular its occasionally euhedral form, suggests that aluminium was at some stage remobilised, at least locally, and then precipitated from solution as gibbsite. These observations suggest that these has been a phase of gibbsite precipitation that may have had a close but complex relationship with regards to the timing of the mineralisation processes, rather than formation as a result of late stage lateritic weathering.

Jul 11, 2011

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Blenkinsop, A Jenkins, H Moore, L Fisher, N Oliver, J Cleverley, M Nugus, J McLellan, J Hill, N Brunacci

The 2 Moz Vogue mineral resource is a recent discovery at the Sunrise Dam gold mine (SDGM), lying approximately 600 m vertically below the Sunrise Dam open pit. Unlike most other lodes, which are dominated either by steep vein sets or shallow high-strain (shear) zones, it lies broadly in the hinge of a folded felsic porphyry body, where it cuts intermediate volcanic lavas and volcaniclastic rocks and is not specifically concentrated at a lithofacies contact. The mineralisation is controlled by a complex interplay of moderate to shallow, west-dipping high-strain zones that are transected by irregular and discontinuous high-grade, north-west-, north–south- and east–west-trending breccia sheets that initially caused problems with attempts to model broad domains. However, by combining the structural controls and styles with the distribution of gold, arsenic, sulfur and antimony, we have improved opportunities for scheduling, extracting and processing the most appropriate material considering the current mining and processing constraints.The early delineation process for the Vogue lode revealed a significant mineral resource for the SDGM, coupled with the recognition of some potentially difficult downstream implications for mining and processing. The ultimate success of mining at Vogue will be a consequence of combining standardised data collection and geological modelling techniques with the results of the novel innovative techniques applied at an early stage of the project.Innovation (in the truest sense) drives change and application to deliver efficient and effective outcomes. Initial data generation and interpretation in lodes above Vogue provided a sound geological model based on strong structural foundations, leading to ideas that could be tested and validated by stress inversion analysis and modelling simulations. Geomechanical modelling simulations, based on the structural analysis, then provided an insight into both the structural and fluid evolution of the system and highlighted target areas. This promoted support for deeper drilling and sampling, which lead to the discovery of Vogue.With additional data, the structural model for Vogue was re-engineered through combination with geochemical and hyperspectral analysis and detailed geological and geostatistical domaining. Initial poor results from metallurgical tests from a small batch sample refocused efforts to undertake mineral and chemical characterisation and profiling (geometallurgy) and combine this data with the composite geological-structural-geochemical model. The result is a conditional probability model for differentiating mineralised or waste domains, with direct outcomes for planning, drilling and mining.CITATION:Nugus, M, Oliver, N, Blenkinsop, T, Hill, J, McLellan, J, Cleverley, J, Fisher, L, Brunacci, N, Moore, H and Jenkins, A, 2014. Exploration and innovation – the discovery and evolution of the 2 Moz Vogue Gold Resource, Sunrise Dam Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 323–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

By Keele R. A

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Tzung-mow Yao, S Ki, J Word, J Vinson

Properly designed evapotranspirative (ET) cover systems can greatly reduce the amount of infiltration and groundwater recharge (deep percolation) into potential acid generating mine waste. In arid and semi-arid environments, infrequent precipitation, low measurable subsurface fluxes, spatial variability within mine waste and cover material, and evapotranspiration from below the cover system create challenges to monitoring moisture flux in these systems. Sloped ET single-layer (monolayer) cover depths and a variety of reclamation treatments are being studied at a copper tailing impoundment in Arizona, USA. To monitor the performance of different ET cover systems in response to precipitation patterns, four different test plots consisting of two different cover depths and two different vegetation densities were instrumented with heat dissipation sensor nests. The sensors measure the soil water pressure potential and allow hydraulic gradients to be determined within and below the cover systems to depths of 180 cm. Three replicate sensor nests were installed in each test plot to account for variability in materials and test plot treatments. Data collection occurs twice daily and is ongoing. Weather during the 26-month monitoring period was characterised by two months of greater than normal precipitation followed by nine months of normal precipitation and 15 months of abnormally dry conditions. Monitoring data indicate that deep percolation occurs in response to periods of extended precipitation, however, drying was observed to depths of six feet below the surface in all test plots. Using conservative assumptions regarding tailing hydraulic properties, one-dimensional downward flux predictions based on the monitoring data indicate very low (Additional long-term monitoring and installation of deeper and replicate monitoring sensors into tailings without cover systems are recommended to evaluate the long-term ET cover system performance and develop a better understanding of deep percolation rates at the sites.

Jan 1, 2003

By W Zirima

A detailed, mine scale non-linear numerical model of Rosebery mine has been built for the purpose of simulating life-of-mine global deformations. The model was calibrated using observations of displacement and damage, and was then used to investigate the correlation between dissipated plastic energy (DPE) and seismic event occurrence. The study is unique because the seismic data was collected over a relatively short period using a temporary portable seismic system. It is the intent to undertake significantly more work, but the analysis of limited data shows that a very good, non-linear relation between DPE and event probability is present. The observed correlation is consistent with measurements from other mines where more data was available. With more data, the strength of the correlation will allow the DPE analysis to be used during the design and sequencing phase of planning to better design the mine to minimise seismic hazards.

Jan 1, 2008

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

By I Swane, R Rait, A Robertson

Geochemical assessment of mine waste materials prior to commencement of a proposed mining operation is a fundamental component of mine feasibility studies and the regulatory approvals process. Static and kinetic geochemical test methodologies are widely used to predict the geochemical nature of mine waste materials and to develop strategies for managing potentially æhostileÆ materials. These data can also be integrated with data from other fundamental studies such as hydrogeology to predict specific environmental outcomes and potential impacts at mine closure and post-closure.A case study is presented for a proposed open pit gold mine in Mongolia, which illustrates how geochemical, hydrogeological and groundwater quality data can be used as part of a geochemical modelling process to predict the final pit lake water quality over time. A series of static and kinetic test geochemical test programs were completed and acquired data integrated with hydrogeological and groundwater quality data provided by the proponent. A widely used geochemical modelling program (PHREEQC) was used to develop the geochemical model and predict water chemistry in the pit void after mine closure. Sensitivity analyses were completed to explore the effects on the model output of groundwater to leachate water ratio, pit wall rock type and climate.Modelling has indicated that pit void water should be pH circum-neutral at mine closure and should remain within Mongolian and World Bank water quality guideline limits under the modelled simulation most likely to occur in the field. Final void water salinity is expected to increase eight fold over 14 years after end of mine life due to a continuous flux of salts (particularly sulfate salts) into the pit lake whilst the pit lake volume will remain relatively constant due to evaporation and a slow recharge rate. Dissolved metal and sulfate salt concentrations in pit water are also predicted to increase over time and could be moderately elevated compared to applied water quality guideline values. Some of the metal concentrations, however, may be lower as these would be expected to precipitate at circum-neutral pH and greater. Recommended additional assessment work on the project when mining commences includes determining the magnitude of adsorption and co-precipitation of metals occurring in the pit void water/sludge system.CITATION:Robertson, A, Rait, R and Swane, I, 2013. Geochemical assessment of mine waste materials and prediction of final pit lake water quality at a proposed gold mine in Mongolia, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 165-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By K Knorr, S Birch

The mineralogy of new certified-reference-materials (CRM) for X-ray fluorescence from Western Australia (ASCRM 030 to 035) was analysed by X-ray diffraction using the BRUKER energy dispersive one-dimensional detector LYNXEYE-XE. The samples were studied using standard-less quantitative phase analysis, based on the Rietveld method. This method delivers the relative amount of crystalline phases. All materials were found to be high-grade iron ore predominantly consisting of hematite and goethite and very low amounts of magnetite. In addition, the gangue mineralogy was characterised. It consists of low-per cent amounts of carbonate (siderite/calcite), quartz, kaolinite, chlorite and gibbsite.Furthermore, all samples were analysed with the external standard method. This is an elegant way to probe for amorphous content without adding an internal standard. All six samples were found to contain up to 16 per cent amorphous or nano-crystalline material.CITATION:Knorr, K and Birch, S, 2013. Mineralogy of new Australian x-ray fluorescence standards, in Proceedings Iron Ore 2013 , pp 269-274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By Feebrey CA, Duncan RA

The Ebor Volcano in northeastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19-20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2-19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (-48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at -19.0-19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichment of SiO2, F,FeO/MgO, alkalies and HFSE.

Jan 1, 1995

By R Symes

The Fosterville Goldmine in Victoria Australia employs the BIOX« Process to liberate gold from its sulfidic flotation concentrate through bacterial oxidation. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation. Once liberated by the oxidation process, the gold is then available for cyanide leaching. During the oxidation process it has been found that a portion of the liberated gold becomes suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. A method was previously developed using an addition of quebracho tannin to significantly reduce this loss by formation of an iron-tannin precipitate which captures the gold which then reports to the cyanide leach circuit with the oxidised concentrate solids onto which it is adsorbed.This paper discusses the development and plant trial of a second processing step to further enhance gold recovery by use of flotation tailings essentially as a source of extra surface area to capture residual tannin-iron precipitate and its associated gold not recovered in the first step.CITATION:Symes, R, 2012. Recovery of colloidal gold from oxidised concentrate wash liquor - Further improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 383-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012