Search Documents

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By A Tawadrous, B Wheeler, D S. Preece, S A. Silling

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Moving rock with explosives rather than mechanical equipment can improve mining efficiency. Such is the case with coalmine cast blasting. Controlling and directing rock movement through explosive deck delay timing can greatly improve ore recovery by segregating ore and waste. In both cases, understanding, predicting and controlling heave is an important element of successful blasting.Computer programs for predicting 2D blasting-induced heave have been used in mining for decades, helping to drive the innovation of new and more efficient mining methods, ie cast blasting. The past few years have seen the advent of 3D distinct element modelling of blast-induced heave. This is an important advancement because most blasting situations are three-dimensional in nature, especially when controlling the direction and intensity of rock movement through explosive deck delay timing.This paper documents the first full-scale blasting simulations in 3D with distinct element models that include hundreds of blastholes and in excess of a million particles, made possible with parallel processing. Surface mineral blasting is the focus of this study which treats the effect of blasthole delay timing on ore recovery. Ore waste and dilution resulting from typical row-on-row delay timing will be demonstrated. Also demonstrated will be the ore recovery possible with delay timing designs that significantly enhance ore/waste segregation. This type of high fidelity modelling and the use of electronic detonators makes possible the sculpting of rock blasting muck into separate piles of ore and waste.CITATION:Preece, D S, Tawadrous, A, Silling, S A and Wheeler, B, 2015. Modelling full-scale blast heave with three-dimensional distinct elements and parallel processing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 127–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010

By F Carrick, W A. Ellis, D R. Mulligan, S I. FitzGibbon

"One of the major environmental impacts of mining is the destruction of habitat. The koala (Phascolarctos cinereus) is an iconic Australian marsupial that has been severely affected by land clearing and its decline is continuing. This has placed pressure upon mining companies and government agencies to ensure koalas are managed throughout the life-of-mines - from land clearing through to rehabilitation of post-mining landscapes. This paper reports on the æKoala VentureÆ research partnership between The University of Queensland and Rio Tinto. As part of the Koala Venture program we examined koala use of two types of restored environments: rehabilitated mined land (20 sites) natural regrowth forests (six sites), at Blair Athol Coal Mine in Central Queensland, Australia. Searches for koala scats revealed evidence of koalas in ten per cent of rehabilitated sites (2/20) and 33 per cent of natural regrowth sites (2/6). Two factors were identified as being of greatest importance in facilitating koala recolonisation of restored habitats. Firstly, all recolonised sites were located close to native forest occupied by koalas (mean 135 m ¦ 52). Proximity to source animals is considered crucial to recolonisation of suitably restored habitats. Secondly, three of the four recolonised sites were dominated by koala food trees, most of which were large enough to be utilised by koalas. Availability of suitably abundant food resources is, therefore, also considered crucial. The requirement for these two factors, in combination, is highlighted by the absence of koalas at several sites that contained abundant food trees, but that were distal to areas with source animals, and vice-versa.Our research demonstrates the enormous potential for restoration of wildlife habitat on post-mining lands, even for species with specific requirements such as the koala. Consideration of the ecological requirements of wildlife during rehabilitation planning is critical to enhancing the likelihood of recolonisation.CITATION:FitzGibbon, S I, Ellis, W A, Mulligan, D R and Carrick, F, 2012. Rehabilitating post-mining landscapes for wildlife - A case study from the Koala Venture research program in Central Queensland, in Proceedings Life-of-Mine 2012, pp 319-324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By L Muñoz, L Steffen, W Vilas Boas, G Gontijo, R Macedo, C Braga, d D Machado, G Stevenson

Mines operating close to communities face growing challenges, especially with their drilling and blasting activities. Proper management of environmental and community impacts is critical to provide sustainability to the mining business in the long-term, by enabling the licensee to operate. This paper will present new technology solutions to minimise the impacts to communities and the environment from blasting operations. A case study of the wireless initiation projects conducted at Kinross Morro do Ouro Mine (located in Paracatu, Minas Gerais – Brazil), will be presented. Focused on overcoming the complex challenges in the mine, Orica and Kinross searched for initiatives to optimise the drilling and blasting operations. The team evaluated the WebGen™ wireless initiation system for controlling environmental impacts as well as operational flexibility and productivity. Since January 2023, three planned wireless blasts to demonstrate the technology and applications were executed. In the tests, the vibration level was able to be maintained lower than the limit of 3.0 mm/s while dust and flyrock impacts were well controlled. The main benefits of using this technology for the Morro do Ouro Mine are: reducing the number of blasts while increasing the blasted mass per month; control of projection of fragments using additional cover; dust control by watering the bench easily; lightning initiation risk reduction due to the absence of wires or tubes on the surface; flexibility in changing the blast day to better control the noise and dust; flexibility in mine planning mining (potential application in the future). The use of the WebGen™ wireless initiation system, enables improved productivity while enhancing safety and reducing impacts to communities. Implementation of this technology has enabled Kinross Morro do Ouro Mine to build trust with its neighbours, maintain the license to operate, and helping to mobilise resources in a sustainable way. This has allowed Kinross to position Morro do Ouro Mine as a world reference operation, especially in relation to innovation, safety, and social responsibility.

Sep 1, 2024

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By B M. H Sharp, R P. Hide, S P. Devine

Uncertainty and debate currently pervade the mining industry in New Zealand. The operational uncertainties, whether external (eg gold prices, the exchange rate), or internal (eg coal expansion difficulties), are large. In addition, many wider factors which influence mining are in a state of flux. State Coal Mines, the operating branch of the Mines Division of the Ministry of Energy I may be made a state corporation, with the remaining Mines Division functions being revamped. The agencies administering environmental legislation are to be restructured. Mining legislation amendments have been proposed and then dropped, and the area is now to be reviewed (The Press, 31 July 1985). Some mining licences have been withdrawn, and become the subject of heated debate in the community (The Press, 19 July 1985, and subsequent letters to the editor).

Jan 1, 1985

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By P V. A van der Westhuyzen

Namakwa Sands is a heavy minerals mining and beneficiation business in the Exxaro Sands Division, and operates along the West Coast of South Africa (see Figure 1). The business encompasses mining, mineral concentration, separation, and smelting operations. Inflated commodity prices and increasing operating costs demands greater attention to the management of process performance and the company wide coordination of resources. Consequently, the task of deploying operational/technical skills and budgets into the most appropriate parts of the business assumes great importance in order to increase productivity from its capital assets. The mineral sands industry is under the same sort of economic scrutiny that all other industries find themselves, and as such, Exxaro – Namakwa Sands has taken the strategic initiative to improve overall resource utilisation within the processing steps and to measure the costs associated with obtaining this value.This paper provides details of the successful implementation of a Kelsey Centrifugal Jig (KCJ) at Namakwa Sands to recover primary and secondary zircon products from the wet gravity (quartz) rejects generated and stockpiled at the Mineral Separation plant (MSP).

Oct 5, 2011

By M I. Pownceby, S Hapugoda, H Han, V Nunna, L Lu

Charcoal produced from Syzygium Zeylanicum (local name: Yakada Maran = iron killer) trees were widely used in ancient Sri Lankan iron smelting practices. In this study, relict charcoal from Syzygium Zeylanicum tree trunks, branches and leaves were analysed for the first time. Unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOX) crystals were identified preserved in plant cell structures by optical mineralogy and SEM analysis. Thermogravimetric Analysis (TGA) of CaOX showed that it displayed three decomposition stages, releasing H2O at 177°C, CO at 493°C and CO2 at 750°C. Following the identification of CaOX in Sri Lankan charcoal, a series of reduction tests on a low-grade, high-P iron ore fine sample (high SiO2: 5 wt. per cent; Al2O3 4 wt. per cent; P: 0.135 wt. per cent) doped with CaOX were carried out at various temperatures. Samples were analysed by XRF, SEM and EPMA to determine the degree of reduction and the effect of reduction on the deportment of impurities, in particular P. Reduction tests at 800°C and 900°C with 5 wt. per cent CaOX showed that the reducibility increased to over 65 per cent. At temperatures above 900°C, P was located mainly within a fine, interstitial glass matrix suggesting that the CaOX flux enhanced removal of P from iron-rich pre-cursor phases to form glass. Preliminary magnetic separation tests to remove the P-rich interstitial glass were unsuccessful due to the fine grain size. Further complete reduction tests at temperatures above 1200°C with addition of coke to convert the iron oxides into Fem were conducted with samples doped with 10 wt. per cent CaOX, 10 wt. per cent CaCO3 and equivalent undoped samples. Results confirmed the preferential P-incorporation into a glassy matrix in the CaOX samples although some rare P incorporation into the metallic phase was noted. Experimental results, including comparisons with the CaCO3 fluxed and undoped samples, are discussed in view of the potential for CaOX flux for removing P (and potentially other impurities) from P-rich iron ores.

Nov 8, 2021

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

Dry magnet separators are used to upgrade and beneficiate a wide variety of minerals such as hematite and magnetite materials. In recent years advances in dry magnetic separators have improved their performance. Fine particle separation is one of the main areas which still remain weak. This paper will present a new design of fine particle drum separators which used for particle size less than 3 mm. A big problem in processing of iron ore is the grade and recovery of mineral values in the fines fraction. The new design high efficiency drum separator is developed to handle fine feeds. In this drum separators both of the drum shell and magnetic yoke rotate in opposite direction. the results showed that when the material feed size was = 1298 μm, drum shell speed was 42.5 rev/min, magnetic yoke speed was 100 rev/min and the maximum intensity of magnetic field was at = 30° the feed grade increased from 50.87 to 65.67 in concentrate box, increase to 60.45 in middle box and tail grade was 24.44. The total achieved recovery for both concentrate and middle box was 81.89 per cent.

Nov 8, 2021

By Z Li, J Pan, D Zhu, W Zhou

In order to enhance the roasting behaviours and metallurgical properties of hematite pellets, which have the problems of high roasting temperature and low compressive strength, a process of producing Brazilian hematite pellets by adding high sulfur magnetite was developed in this paper, and process parameters have been optimised. It is shown that the roasting temperature decreases from 1320¦C to 1200¦C by adding 30 per cent of high sulfur magnetite. New Fe2O3 crystal oxidised from Fe3O4 is more active, which is beneficial to induration of pellet. When the ratio of magnetite increased to 50 per cent, only about 90¦C of the roasting temperature was decreased. Higher ratio of high sulfur magnetite causes more porosity of pellets because of oxidative desulfurisation, which is harmful to the strength of roasted pellets. The reduction disintegration index (RDI), presently RDI+3.15 of product pellets is aggrandised from 87.79 per cent to 99.54 per cent and 97.55 per cent, and the reduction swelling index (RSI) is lowered from 36.25 per cent to 12.50 per cent and 6.25 per cent respectively, by adding 30 per cent and 50 per cent of high sulfur magnetite. The compressive strength of roasted pellets is elevated obviously by adding high sulfur magnetite, which resists the inner stress of pellets during reduction process, so as to enhance the RDI and reduce the RSI of product pellets. In addition, the inner porosity may be filled by the swelling during the reduction process, which can also lower the RSI. The process provides a low power consumption of making hematite pellets that high sulfur magnetite can decrease roasting temperature significantly and improve the metallurgical properties of hematite pellets dramatically.CITATION:Zhu, D, Zhou, W, Pan, J and Li, Z, 2013. Study on improving roasting behaviours and metallurgical properties of Brazilian hematite pellets by adding magnetite with high sulfur content, in Proceedings Iron Ore 2013 , pp 525-530 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

The Bradford Process, Australian Patent No. 11253, has had considerable application in the treatment plants of Broken Hill mining companies, and is at present being used by the North Broken Hill Limited for the treatment of weathered slime accumulations.The "Mining and Scientific Press," of 28th September, 1918, describes the Bradford Process at Broken Hill, specially featuring its application to slime material at the Proprietary mine-the home of the process.The points then stressed for galena flotation were acidulated slime pulp (0.025 to 0.030% H2S04) at temperature 85° to 90° F. and suitable time contact, with 1.5 to 2 lb. of sodium hyposulphite (per ton on slime) to permit the released S02 to "wet" or depressthe blende mineral. Also 1.0 to 1.3 lb. of crude sulphur (per ton on slime) was burnt, to supply S02 for keeping the lead concentrate clean during flotation. Pulp density varied from 23 to 26% solids. Since 1918 the process has been simplified in its application.Acidity of circuit, temperature, and sodium hyposulphite have been dispensed with, and now the S02 is practically all obtained by burning crude sulphur. I The plant units now employed for control and absorption of S02 gas constitute the main advance made in process, and these, with other details, are fully explained in this paper.APPLICATION AT BROKEN HILL NORTHThe existing North Broken Hill Limited gravity mill commenced operations on 9th September, 1909.

Jan 1, 1929