Search Documents

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By M A. Rhamdhani, R Z. Mukhlis

Removing the ledge formation in the Hall-Heroult cell during the electrolysis process may significantly reduce the energy requirement of the aluminium production process. In the absence of the ledge, however, the sidewall-material types become heavily restricted since the cryolite is very corrosive at the electrolysis temperatures. This paper study the corrosion behaviour of sintered nickel ferrite, nickel aluminate, and magnesium aluminate refractories (as possible candidates for sidewall material) in molten aluminium and cryolite melts with various alumina content at 980°C. Immersion tests of refractories with various porosity were conducted to assess the suitability of the refractories in the corrosive environment of the electrolysis cells. Microstructural change of the refractory after immersion were analysed using secondary scanning electron microscopy (SEM). Sampling of the melts were taken at 0, 10 min, 30 min, and each hour up to 6 hrs, and subsequently analysed by Inductively Coupled Plasma (ICP) spectroscopy. Based on the projected concentration of the refractories constituents in the melts, it was predicted that the corrosion rate of NiFe2O4, NiAl2O4 and MgAl2O4 in cryolite with 11 wt per cent Al2O3 were 461 × 103, 1.03 × 103, and 798 × 103 cm/a, respectively. Much lower corrosion rate of 2.3 cm/a for NiFe2O4, 2.6 cm/a for NiAl2O4 and 0.3 cm/a for MgAl2O4 were predicted if the refractories in contact with aluminium melts. Erosion played an important role in the corrosion as the concentration of the refractory constituents in the melts were beyond its solubility limit. It is therefore crucial to increase the densities of the refractory and improve its wetting characteristics.

Aug 21, 2024

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Johnston RRM

There have been many published mathematical models that, to varying degrees of sophistication, attempt to describe dynamic thickener behaviour. CSIRO has undertaken to develop a model under industry sponsorship. Recently developed instruments such as the floc density analyser and natural gamma-ray gauge have enabled new data to be collected from plant thickeners for model validation and development. The principles behind the use of the natural gamma-ray gauge are described and the possibilities for its use as a control instrument in the bed have been examined. A simple nomograph illustrates how the gamma-ray gauge data can be used to predict steady state underflow consistency and bed Position.

Jan 1, 1991

By M T. Grigoleit, M S. Schneider

The iron ore industry in Australia has, in recent years, experienced an unprecedented growth phase. But now that major expansions are moving into the operation phase, new challenges have emerged. Whereas initial planning may involve a few modelling studies, ongoing performance monitoring and improvement requires a different, more intense approach. This is especially important in the face of changing factors such as commodity prices, exchange rates and labour markets. Response time is key. As a mining operation proceeds from initial planning to daily operations, the time window for analysis shortens, going from months to weeks to days as the business matures.Simulation models and analysis tools are typically built and run by specialists in the planning phase, but then what? The investment has been made, but realised only once. What if further analysis could be carried out in-house, re-using existing models using up-to-the-minute data? Can we create virtual mines that run in parallel to live operations that allow computers to identify areas of a value creation or operational improvement? These questions can be answered by the innovative application of big data, simulation and predictive analytics. The future will be having this all integrated into one platform that offers, for the first time, an opportunity for non-experts to apply existing modelling and analysis assets – combined with live data – to deliver support for continuous improvement, and the ability to respond quickly to external changes in the best possible way, before they become big problems. These techniques will represent a step change in the ability for operations to maximise efficiency and will underpin the intelligent operations of the future. These issues are addressed in this paper.CITATION:Schneider, M S and Grigoleit, M T, 2015. Maximising productivity through big data, simulation and predictive analytics, in Proceedings Iron Ore 2015, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By Wooltorton B

Highwall failures in surface coal mines in Queensland occur as circular slips through weak and weathered material, or as bilinear slides on sub-horizontal surfaces and steeply dipping joints. Weak horizontal planes occur in the Permian-Tertiary unconformity or on bedding surfaces within the Permian Coal Measures. Sub-vertical movements occur along rock joints and tension cracks induced by stress relaxation after excavation. Blasting also introduces new fractures and causes movement along existing rock discontinuities. Critical factors for stability include the dip direction of potential failure surfaces, shear strength of the rocks, damage due to blasting prior to highwall excavation, groundwater conditions, the type and performance of clays on shear surfaces, and pit geometry.

Jan 1, 1981

By J Joy, D Griffiths, A Bye, G V. Kizil

Poor standards of electrical installation and maintenance continue to contribute to electrical related fatalities and injury risk in the mining industry. Electrical isolation has the potential to initiate major unwanted events (MUEs) and as such requires thorough analysis to demonstrate adequate management. There have been 719 incidents related to accidental contact with electricity over the past five years in the Queensland mining industry (Queensland Government DME, 2012a, 2012b) with the last fatality being recorded in 1997 (MESA, 2012).A project funded by the Australian Coal Association Research Program (ACARP) has developed a form of a safety case using the four-layered æCoal Mine Safety Regime (CMSR)Æ approach. The CMSR is transparent and robust as it includes full site risk assessment and special issues risk assessment to be demonstrated as part of the process.The practical application of the CMSR has been demonstrated using a longwall mining case study site, where a unique 11 kV armoured face conveyor (AFC) is in operation. The case study has involved progressive application of the requirements of each layer of the CMSR (see Figure 1) to high voltage (HV) electrical isolation related issues. The project has specifically concentrated on understanding and analysing two high priority MUEs, electric shock and unplanned movement of equipment, through Layer 1 analysis. These two MUEs are an important part of the project as they have demonstrated the steps that may be taken to satisfy the risk management processes at Layer 1 of the CMSR and have contributed to resolving issues at the other three layers of the CMSR.The analysis of HV electrical isolation has been used as an exemplar to demonstrate the CMSR process and its practical application. The CMSR is applicable to major/principal hazards management as identified by the New South Wales and Queensland jurisdictions.This paper provides an overview of the development of a form of safety case using the CMSR and introduces the case study application for HV electrical isolation risk management at underground coal mines focusing on the major unwanted event of electric shock.This project provides the mining industry with a documented, publicly accessible, form of safety case using the CMSR approach for the first time.CITATION:Kizil, G V, Griffiths, D, Bye, A and Joy, J, 2012. Using a coal mine safety regime approach to the management of high-voltage electrical isolation, in Proceedings International Mine Management 2012, pp 59-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By D Willis, A Shanahan, C Jacobs, T Luxner

The application of tunnel boring machines (TBM) for reef mining is a unique practice with benefits over current mining methods given the right geology and geometry of the orebody. The Stillwater Mining Company (SMC) of Nye, Montana, USA operates two mines for obtaining platinum metals. The operation is currently using a 5.5 m diameter open-type machine for further mine development, as well as another TBM that they own.The latest 7.1 km bored tunnel, known as the Blitz Tunnel, will be routed parallel to the ore deposit in igneous mafic intrusive rock, and will be used for the life of the mine operation. It will be used to map the ore deposit, and provide a rail haulage route.Detecting the reef in relation to the TBM requires careful analysis. Diamond core drilling occurs ahead, above, and alongside the machine at every 150 m. The core is drilled, logged, and interpreted on the spot, concurrent with boring. Based on the data, the TBM is readjusted so that it stays on the correct bore path.This paper will highlight the application and benefits of TBM usage for reef mining, with detailed descriptions from the mine site.CITATION:Willis, D, Jacobs, C, Luxner, T and Shanahan, A, 2014. Tunnel boring machine usage speeds up development at Stillwater Mine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 683–690 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

By Jones J. P, Arriagada J, Scherpenisse C. R

A recently-developed model is used as a tool to optimise the design of blasts used to create final walls in large open pit mines. The use of this tool has allowed present blasting practice and proposed designs to be evaluated to predict the likely extent of rock damage behind the final wall. The evaluation of the damage is dependent on the predominant local geology. Modelling of damage using the software allows the potential zones of rock damage to be evaluated under the following criteria: I . the extent of new fractures formed in the intact rock mass; and 2. the distance to which dilation and extension of existing discontinuities and pre-existing fractures will likely occur. The computer model has been used to examine present blasting practice and to estimate the damage induced by final and intermediate rows of blastholes. The results of current practices are presented in a visual form that allows simple comparisons to be made for any proposed changes in design. To confirm the predictions of the modelling, physical measurements are being undertaken at selected mines to quantify damage behind blast patterns, and experimental programs are underway to measure near-field vibration, or shock, levels. The computer modelling software is being used to qualify and improve the design of final rock slopes in large surface mining excavations, and to provide site engineers with well-defined design criteria for consistency in design. The model is seen to be just one of many tools which are being used in large open cut mining operations to gain an improved understanding of blasting and blast control.

Jan 1, 1995

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

By D J. Hill

"Mining companies routinely invest in improvements to their processing operations, but often these enhancements do not work to full effect.Improvements can be ineffectual because underlying process problems are not identified or prioritised for correction or repair.This is frequently because ‘black box’ solutions deployed to implement process control improvements typically rely on instrumentation to provide data for algorithms to work effectively, and these solutions are often ineffective or disabled at mineral processing sites.There are three key reasons they can fail to deliver: vital instrumentation is not calibrated or functioning as required basic process control and loop tuning was not implemented correctly or is in need of tuning there is an inability to support the ‘black box’ solutions on-site.Many of these problems can be overcome by implementing operational analytics that identify where problems are occurring and prioritise where improvements need to be made.Incorporating operational analytics into process improvement is not a new methodology. It is more a back-to-basics approach to make more efficient use of capital and systems already deployed.Data collection systems, such as the OSIsoft PI System, provide real-time and historical process information for process control experts to analyse and identify areas for improvement. However, most systems are not used effectively. With some simple enabling, data collection systems can provide evidence for prioritising investments in improvements and determining an investment’s effectiveness.MIPAC advocates that the initial step, with analytical evidence, is that clients review the control strategies and implement small influential instrument repairs/calibrations and operator training. This can significantly boost process productivity without the need to spend large sums of money on new capital or employing expensive, difficult to maintain ‘black box’ solutions.A simple Stage-Gate®-style approach ensures that small investments in evidence-based process improvements deliver significant benefits to mining operations.CITATION:Hill, D J, 2014. How to prioritise process improvements, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By K G. van den Boogaart, M Lehmann, U Mueller

Geometallurgical parameters are descriptions of the mineralogy and microstructure of the ore determining its mineralogical and microstructural characteristics. From a conditional geostatistical simulation of such properties, a processing model can compute recovery, equipment usage, processing costs, and thus the monetary value for mining and processing a block with certain processing parameters. The output can be used for optimising mining sequences or finding optimal processing parameters by solving the corresponding stochastic optimisation problem.The approach requires two properties of the simulation not provided by established geostatistical techniques:Many relevant geometallurgical parameters are from non-Euclidean statistical scales such as (mineral) compositions, (grain size) distribution, (grain) geometry, and (stratigraphic type) categorical, which might produce nonsensical values (for example, negative proportions, negative facies probablities, planar grains) when simulated with standard geostatistical techniques.Due to the nonlinearity of processing, the entire conditional distribution of the geometallurgical parameters is relevant, not only its mean and variance. The geostatistical simulation needs to reproduce the joint conditional distributions of all the geometallurgical parameters.The multipoint conditional geostatistical simulation technique discussed here allows for jointly simulating dependent spatial variables from various sample spaces. The technique combines an infill simulation, similar to the one used in multipoint geostatistics, with a new form of distributional regression to estimate conditional distributions of arbitrary scales from different information sources, including training images, training models and observed data. The distributional regression is based on a generalisation of logistic regression and is related to both Bayesian Maximum Entropy geostatistics and high order cumulants.The method ensures that simulated data reside in the set of possible values and honour the characteristics of the joint distribution to be reproduced. The computational effort is substantial, but affordable for a useful application with standard problems: from processing-aware block value prediction and block processing optimisation as shown in the test application to a mathematically completely defined simulated model situation with a complex processing model.CITATION:van den Boogaart, K G, Tolosana-Delgado, R, Lehmann, M and Mueller, U, 2014. On the joint multipoint simulation of discrete and continuous geometallurgical parameters, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 379–388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By E Jak, G Khartcyzov, M Shevchenko

The increasing complexity of ore resources and recycled materials in the feed of pyrometallurgical processes present a technical challenge to the metallurgical engineers working on maximising the recovery of the valuable elements and minimising the environmental impact of the processes. To address this challenge, the availability of computational tools that can predict the mass and energy balance in complex systems is required. Then the accurate description of phase equilibria in the complex multicomponent systems describing the chemistry of the pyrometallurgical processes becomes critical for the correct implementation of the indicated tools and facing the outlined industrial challenges. In the present study the distribution of selected elements (Pb, Zn, Fe, As, Sn, Sb, Bi and Ni) between oxide liquid and metal in the ‘CuO0.5’-CaO-AlO1.5 system in equilibrium with Cu metal at 1400°C (liquidus of CaAl2O4) was experimentally studied using the equilibration and quenching technique followed by the electron probe X-ray microanalysis of the resulted samples. The study covered a wide range of effective p(O2) over the system from 10-11 to 10-3.5 (corresponding to formation of immiscible CuO0.5-rich slag). To avoid loss of volatile elements (Pb, Zn, As, Sn, Sb and Bi), a correlation between ‘CuO0.5’ in oxide liquid and p(O2) in open system was obtained first, followed by studying the volatile elements distribution in closed conditions (Al2O3 crucible sealed in SiO2 ampoule), where ‘CuO0.5’ concentration was used as a marker to evaluate the effective p(O2) over the system. The experimental results were then used for the optimisation of the thermodynamic model parameters of the system as part of the integrated experimental and self-consisting thermodynamic modelling research program of phase equilibria in the Cu-Pb-Zn-Fe-Ca-Si-Al-Mg-O-S-(As, Sn, Sb, Bi, Ag, Au, Ni, Cr, Co and Na) gas/oxide liquid/matte/speiss/metal/solids system.

Jun 19, 2024

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (IMR) separators.The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990