Search Documents

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By Jr. Baldwin. William M

WELL known to every metallurgist is the fact that different production schedules will profoundly affect the character of annealed metal strip. Yet the number of conditions [ ] that may be wrought by different combinations of rolling and annealing schedules is so myriad that despite the continual research that is being applied to this subject, the complete picture is not yet known. Copper, like all other metals, during the process of rolling or annealing, develops certain crystallographic configurations which should not be dismissed as being too impractical, for the crystallographic condition existing within the metal is a principal influence upon both the external mechanical properties and the behavior of the material [ ] when it is subjected to such operations as bending, flanging, drawing, and so forth. EFFECT OF ROLLING AND ANNEALING UPON THE CRYSTALLOGRAPHY OF COPPER STRIP The most salient points in the crystallographic reactions of polycrystalline copper to rolling and annealing may be best represented graphically by a "map" such as that given in Fig. I. I. As copper strip is cold-rolled from a randomly oriented structure (pole figure I),

Jan 1, 1942

Jan 1, 1970

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By M. A. Mosher

Most modern electrolytic copper refineries have found it expedient to build and operate a complete secondaries plant for the treatment of the electrolytic slime accumulated in the cells during the corrosion of the copper anodes. In the earlier years this was done for the sole purpose of promptly recovering in marketable form the silver and gold contained in the slime. Later, improvements in refining methods made possible the recovery of the more precious metals such as platinum, palladium, osmium and iridium, and in recent years, due largely to an increasing market, many secondaries plants have undertaken the commercial production of selenium and tellurium. The complete up-to-date secondaries plant, or silver refinery as it is usually called, is therefore equipped for the production in marketable form of from six to eight metals. The physical plant and operations may be separated into six main divisions: 1. Slime treatment, in which the raw slime is treated by wet methods for the removal of its high copper content and portions of other impurities such as arsenic, selenium and tellurium. 2. Furnace refining, in which the remainder of the base-metal content of the slime is removed by fluxing and fire-refining. 3. Electrolytic parting and refining, in which the silver and gold are parted and obtained in the pure state. 4. Melting of silver and gold into marketable form. 5. Recovery and refining of the more precious metals. 6. Recovery and refining of selenium and tellurium. The Silver Refinery of the Raritan Copper Works at Perth Amboy, N. J., is a complete secondaries plant and the following description of its equipment and processes is, in a general way, typical of other plants of its kind. Slime Treatment The raw slime, pumped with a minimum amount of cell solution from the electrolytic copper refinery, is discharged into the center of circular settling tanks 15 ft. in diameter by 8 ft. deep, where the slime settles out and the solution overflows peripherally to return to the copper refinery by gravity. The slime is then dropped through a bottom outlet to a

Jan 1, 1934

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By J. E. Spurr

The region here discussed is that part of Western Nevada in which. during the last few years. discoveries of rich gold- and

Jan 1, 1906

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By J. B. Mackintosh

THE quantitative determination of copper, by means of electro-deposition, offers so many advantages, that it is to be preferred, when properly executed, to all other methods for ease and accuracy. The object of the present paper is to give the results of a number of experiments made during the past few months, and to indicate some sources of error, which must be avoided in order to attain the necessary accuracy. In 1867, C. Luckow, in competition for a prize offered by the directors of the Mansfield Copper Works, submitted the following

Jan 1, 1882

By J. B. Mackintosh

The quantitative determination of copper, by means of electrodeposition, offers so many advantages, that it is to he preferred, when properly executed, to 611 other methods for ease and accuracy. The object of the present paper is to give the results of a number of experiments made during the past few months, and to indicate some sources of error, which must be avoided in order to attain the necessary accuracy. In 1867, C. Luckow, in competition for a prize offered by the directors of the Mansfield Copper Works, submitted the following

Jan 1, 1882

By W. H. Bassett

W H. BASSETT was elected first vice-president at . the executive session of the new Board on Tues- day afternoon. Karl Eilers, H. Foster Bain, Thomas T. Read, and H. A. Maloney were respectively re-elected as treasurer, secretary, assistant secretary and assistant treasurer. The new Executive Committee will consist of W. H. Bassett, Chairman, and Richard Peters, Jr., H. C. Bellinger, E. De Golyer, Edgar Rickard. The Finance Committee will be J. V. W. Reynders, Chair- man, Henry Krumb and H. G. Moulton. George D. Barron was reappointed Chairman of the Admissions Committee, and F. Julius Fohs put in charge of the Papers and Publications Committee.

Jan 1, 1929

By J. A. Herbst, D. W. Fuerstenau

An analysis of the kinetics of dolomite grinding in a dry ball mill reveals that the following approximations apply for the parameters of the batch grinding model: (1) the size discretized selection functions are proportional to the specific power input to the mill, and (2) the breakage functions can be taken as invariant. These approximations are shown to provide the basis for accurate predictions of product size distributions obtained for several mill speed, ball load, and particle load combinations within the normal ball mill operating range. The engineering implications of these findings are discussed.

Jan 1, 1974

[ ]

Jan 1, 1938

By Gerald Edmunds

Although the phenomenon of season cracking is still imperfectly understood, there seems to be ample evidence that season cracks are propagated by the combined action of corrosion and a stress of either internal (residual) origin or external origin. The factors that influence season cracking may therefore be grouped according to corrosive media, nature of stress, and character of the material. Thus the important mass of evidence pointing to ammonia as the most frequently active corroding agent causing season - - cracking of brass has naturally led to the development of laboratory tests of a moderately accelerated character based upon ammonia together with auxiliary agents such as air, water vapor, and carbon dioxide as the corroding agent. Similarly, the knowledge that stress must be present has led to the use of externally applied and therefore accurately measurable stresses in laboratory testing. A companion paper(^)^ to the present one discusses the development of these test methods in our laboratories. The present paper discusses data bearing on factors concerning the nature of stress such as its magnitude and direction of application. It also deals extensively with the character of the brass, particularly in regard to the copper-zinc ratio and the structure as developed by mechanical work-

Jan 1, 1945

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By D. Ott

Results of a research project on investment or lost wax casting will be presented. The project was concerned with various aspects of the process as they are typical for the production of jewellery from gold alloys. During these investigations testing methods for investment quality as well as for casting quality and the various process parameters were developed and charateristic defects as they occur in practice were traced back to their origin in the process. Investigated were various static casting and centrifugal casting methods in different atmospheres as well as vacuum casting in devices of different design. It was shown that independent of the method a close control of the many process parameters interfering with each other is essential for a quality casting.

Jan 1, 1984

By H. R. Aldrich

This paper is not a treatise on the theory and practice of magnetic surveying. It presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretation of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies. It is considered probable therefore, and certainly it is the hope of the writer, that the appended charts, or magnographs, which show how character of the country rock and its changes, structural strike and dip and their changes, depth of burial and its variation, contact metamorphic

Jan 1, 1929