Search Documents

By R. W. Jenkins

RACKLESS equipment is being used by the T Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used instead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone. It was known that the argillaceous cement rock was underlain by crystalline high calcium limestone. After an extensive drilling program it was found that there were large reserves of limestone underlying a recumbent syncline exposed in the south wall of the company's No. 3 cement rock quarry. A quarry was started on the vertical limb of this fold in 1927, and by 1930 the full requirement of the plant was met. After 1945 production diminished because of the occurrence of dolomite beds in the south wall. The quarry floor was then 135 ft below the cement rock level and 285 ft below surface. In 1949 Gerald I?.

Jan 1, 1955

By D. Turnbull, R. E. Cech

Small particles, 10-20 microns diameter, of a 28.6 atom pct nickel, balance iron alloy, have been supercooled 186 C with respect to bulk alloy M, temperature. Particles exhibit a marked mechanical shock sensitivity while being held in a supercooled state. The tendency for shock to induce martensitic transformation appears to be a maximum at —140 to —160°. Slow cooling of particles in mechanical contact with one another results in extensive martensite formation. This is prob-ably the same effect as the catalytic effect observed in polycrystals where martensite formation in one grain induces transformation in other grains. AS a result of extensive research over the past decade on the martensitic transformation, a much better though not complete understanding of the transformation has resulted. Recent reviews by Bilby and Christian' and Kaufman and Cohen2 have

Jan 1, 1959

By G. E. Johnson

E. D. HYMAN*—How much sorting of scrap is done ? G. E. JOHNSON (author's reply)—We do practically no sorting. We charge "run of mine" scrap to the furnace. The unmeltables, mostly iron, are in such demand today that there is no difficulty in disposing of them. It may soon be desirable to sort out from the unmeltables as much of the brass as possible. J. J. BRUGMAN†—We have somewhat similar problems in the secondary aluminum business. What is your method of removing the unmelted material from the furnaces? Why have you such an apparently small space in which to charge your materials? Do you find that you have to seal that opening, or can you have it open and continuously charge at one end and pull out the other ? G. E. JOHNSON—Our means of melting scrap is efficient only to the extent that we use the waste heat from the vaporizing chamber to do the job. It is a batch process. We open the charge door and place the scrap on the hearth by hand shoveling. The door is then closed during the melting down period. After the melting is complete, the opposite door is opened and the unmeltables are raked out. The doors are approximately 3½ X 4½ ft and are not sealed during the process only closed. They are nominally tight. Some metal is oxidized in the process. We have visualized a means of conveying the materials through this melting unit with the metals that are melted trickling out during its travel. T. H. WELDON‡—Mr. Johnson, in line with the last question, is it necessary to seal the furnace between the melting down and the vaporizing unit, or have you got an inverted syphon in the bottom of the chamber? G. E. JOHNSON—That was one of the first things we encountered. We had to have a sealed opening, and it is a molten metal seal. You have indirectly asked me another question, which was: "Do you have to seal up the melting unit?" I would say we should exclude as much air as possible, although we are not too efficient in doing that. We allow the melting unit doors to be open when we charge and when we remove unmeltables. You can readily see that that would lead to the idea of having a controlled atmosphere in the melting unit, and I think this would do a more efficient job of melting the scrap. T. H. WELDON—How often do you charge the furnace? G. E. JOHNSON—We charge the melting unit, and rake out the unmeltables, about every hour. H. R. HANLEY*—Are any provisions made for controlling the rate of oxidation for the production of various size particles for certain characteristics of the zinc oxide product? G. E. JOHNSON—Yes, there are many. You are getting pretty much into the fine points of zinc oxide manufacture. Some of us still think we have something to learn about that. In general, this muffle furnace as I have described it to you produces a rounded particle of zinc oxide which is generally formed by a rapid oxidation of the zinc vapor, followed by rapid cooling. We have gone to the other extreme in some of our experiments. We have changed the furnace to produce a type of zinc oxide, such as we thought was peculiar to American process zinc oxide, by controlling the temperature at the point of oxidation and maintaining that temperature for a much longer period of time than we do when we make the rounded shape. There are other relationships that this furnace readily provides. One of the important factors is the ratio of air to zinc vapors. We can vary that by varying the air supply to the baghouse, or vary the rate at which we are vaporizing the zinc by the simple expedient of regulating the temperature over the carborundum arch. We have a number of variables that permit us to produce all of the grades of French process zinc oxide from lead-free up through the highest grades of seal oxides. There are many controls that we can apply to the operation. What I have said is but a brief condensation. K. MORGAN*—Can Mr. Johnson give us some idea of the fuel consumption of the furnace ? How much oil does he use per ton of zinc distilled? I am also interested to know what sort of heat transmission he gets through the arch? What is the thickness of the tiles used to construct the arch? Some time ago we built a small furnace for a different purpose, using a carborundum arch, and we found that the reflectivity of the molten zinc surface was so great we had to use a very high arch temperature. We found we made an improvement by having a layer of carbon on the surface of the zinc. Has Mr. Johnson had any experience on these points ? Does he make any sort of insolu-bles which he leaves in the furnace which he cannot tap out ? G. E. JOHNSON—I believe your first question was the fuel consumption. If I recall, somewhere in this paper there is a test that I quote. I believe we used 800 gal in a given period of time. Offhand I cannot translate that into tons of metal. I might also state that we have this understanding; that the carborundum arch, as the temperature becomes higher, becomes more efficient in heat transmission. As a matter of fact, I believe it is at about 2600°F or higher that the highest efficiency of heat transmission becomes available. We have calculations that I cannot quote from memory which indicate that the carborundum arch does a really very fine job for this type of furnace. Another point that we had considered was the fact that this furnace could be readily constructed so as to furnish an ideal source of heat for waste heat boilers. If a carborundum arch was used over the melting unit, we would have no zinc vapors in the gases at all— just clean combustion gases from which we would have removed some of the heat. L. P. DAVIDSON†— The insolubles

Jan 1, 1950

By R. G. Aspden

Crystals with an (001) [loo] initial orientation of an iron-base alloy containing 3 pct Si were cold rolled with and without the use of constraints. A major difference in the rolling and annealing textures was observed between crystals rolled with and without constraints. These data show that the contribution of constraints at grain boundaries in a poly crystalline sheet should be considered in applying textural data on single crystals to grains in an aggregate. SILICON-iron alloys with a cube texture have been recently developed and their magnetic characteristics reported.1-4 Of interest in the development of this texture were the textural changes of single crystals accompanying rolling and annealing and the influence of constraints at grain boundaries in an aggregate on the behavior of individual grains. The present study was primarily concerned with the effect of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001)[100]. Barrett and Levenson5 were among the first to observe an influence of constraints at grain boundaries on the textural changes of individual grains during deformation. They tested Taylor's6 theory of plastic deformation of face-centered-cubic metals in which deformation textures were predicted. About one-third of the grains in poly crystalline aluminum did not rotate as predicted. Grains of the same initial orientation were observed to rotate in different directions under the influence of applied stress and anisotropic flow of neighboring grains. Recently, the various inhomogeneities of flow of crystals in an aggregate have been studied7'8 and reviewed.9-11 Barrett and Levenson" rolled (001) [loo] iron single crystals inserted in close-fitting holes in copper to limit lateral flow and to simulate rolling of grains in an aggregate. Deformation bands were formed after a 90 pct reduction in thickness, and the cold-rolling texture contained two components described by rotating the (001)[100] about 35 deg in both directions around the normal of the rolling plane. No annealing textures were reported. Chen and Maddin13 rolled molybdenum single crystals initially (001) [loo]. The crystals were mounted between two hardened silicon-iron plates and 96 pct reduced in thickness by rolling at a low rate of reduction, about 0.0001 in. per pass. The deformation texture had the mean orientation of (001) [loo], and the azimuthal spread included orientations described by rotating (001) [loo] about 35 deg in both directions about the pole of the rolling plane. The presence of deformation bands were not reported by Chen and Maddin or detected in subsequent work of Ujiiye and Maddin.14 The ideal orientation of the annealing texture was (001) [loo]. Recently, Walter and Hibbard 15 reported on the textures of 3 pct Si-Fe alloy crystals initially near (001) [loo]. Each crystal was in an aggregate cut from a columnar ingot. After 66 pct reduction by rolling, the texture consisted of two symmetrical components which had the orientations described by rotating (001) [loo] about 30 deg in both directions about the pole of the rolling plane. Annealing texture was near (001) [loo]. In the above work, the textures of body-centered-cubic crystals were studied after rolling under the influence of constraints. The deformation textures varied from (001) [loo] to near the (001) [110] type and appeared sensitive to the manner in which the crystals were rolled. No textural data were available on the effect of rolling (001) [loo] crystals with and without constraints. The purpose of the present work was to evaluate the influence of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001) [loo]. Rolling and annealing textures were studied for a) crystals rolled with no constraints at different rates of reduction, and b) crystals rolled with constraints imposed by neighboring grains and by plates between which a crystal was "sandwiched". PROCEDURES AND EXPERIMENTAL TECHNIQUES Data are presented on four crystals which are representative of several crystals studied. The orientation of each crystal prior to rolling was (001) [loo] as determined by the Laue X-ray back-reflection method," i.e., each crystal had an (001) within 3 deg of the rolling plane and [100] within 3 deg of the rolling direction. These crystals were obtained from two iron-base alloys containing 3 pct Si by weight which were prepared by vacuum melting electrolytic iron and a commercial grade of silicon. Crystals 1, 2, and S-1 were cut from a large single crystal grown from the melt of one alloy by the Bridgman technique17 in an apparatus described by

Jan 1, 1960

By Basil Prescott

Resume.-The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre¬mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide types occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore. The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition.

Jan 2, 1915

By John Wulff, Robert Kamm, Steinberg Morris

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin's diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947

By John Wulff, Steinberg Morris, Robert Kamm

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin's diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS as to the methods of smelting ores and of obtaining metals I discussed in Book IX. Following this, I should explain in what manner the precious metals are parted from the base metals, or on the other hand the base metals from the precious'. Frequently two metals, occasionally more than two, are melted out of one ore, because in nature generally there is some amount of gold in silver and in copper, and some silver in gold, copper, lead, and iron ; likewise some copper in gold, silver, lead, id iron, and some lead in silver ; and lastly, some iron in copper2. But I will begin with gold. Gold is parted from silver, or likewise the latter from the former, whether it be mixed by nature or by art, by means of aqua valens3, and by powders which consist of almost the same things as this aqua. In order to preserve the sequence, I will first speak of the ingredients of which this aqua is made, then of the method of making it, then of the manner in which gold is parted from silver or silver from gold. Almost all these ingredients contain vitriol or alum, which, by themselves, but much more when joined with saltpetre, are powerful to part silver from gold. As to the other things that are added to them, they cannot individually by their own strength and nature separate those metals, but joined they are very powerful. Since there are many combinations, I will set out a few. In the first, the use of which is common and general, there is one libra of vitriol and as much salt, added to a third of a libra of spring water. The second contains two librae of vitriol, one of salt-petre, and as much spring or river water by weight as will pass away whilst the vitriol is being reduced to powder by the fire. The third consists of four librae of vitriol, two and a half librae of saltpetre, half a libra of alum, and one and a half librae of spring water. The fourth consists of two librae of vitriol, as many librae of saltpetre, one quarter of a libra of alum, and three-quarters of a Mbra of spring water. The fifth is composed of one libra of saltpetre,

Jan 1, 1950

By I. W. Wark

AN attempt has been made to compare the influences of the two most widely used depressants-alkalis and sodium cyanide-and the most widely used activator-copper sulfate-on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in this group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,1 was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating results, the other four collectors were tested in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed.

Jan 1, 1934

By Murray F. Hawkins

One problem of reservoir engineering is the early estimation of the size of newly discovered reservoirs. Often these reservoirs are the expansion type in which sizeable pressure drops occur incident to the production of small fractions of the oil reserve, above the bubble point, and a material balance equation may be solved to find the reserve. The early form of this equation' considered only the compressibility of the oil. Later Hall2 showed that the compressible nature of the formation rock is a significant factor in production above the bubble point, and he presented a new equation which includes a formation (rock) compressibility term. This note presents a further extension of the material balance equation as applied to volumetric, unsat-urated reservoirs above the bubble point by including a term for the presence and compressible nature of the interstitial water. DERIVATION OF EQUATION During a decline in average reservoir pressure, ?p ?p, — p1 the initial reservoir volume V,, will decrease to some value V, due to the reduction in pore volume as a result of a decline in the hydrostatic pressure within the formation, and v, = V,, [l — cr ?p]......(1) The formation compressibility c, is expressed in terms of change in pore volume per unit pore volume per psi. Simultaneously the connate water within the formation expands from an original volume V,, = S,V,, to a new volume V,, V, = s,v,, [I + c,npl.....(2) The difference [Vp — V,] is the hydrocarbon pore volume at pressure p and may be equated to the volume of the remaining oil, or [N — N,] B, = V,,, [I - C~A;] - S,.Vpi [l + cwnjl.........(3) But the initial oil in place in terms of the initial reservoir volume, connate water, and formation volume factor is Ilividing Equation 3 by Equation 4 eliminates V,, to give,

Jan 1, 1956

By C. H. Mathewson

COPPER and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.1 It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of. the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

C. G. Dunn (Generai! Electric Research Laboratory)— The author is to be commended on his attempt to calculate the residual strain energy from information on the dislocation density within the subgrains and a surface energy associated with the subgrains. However, much closer agreement between a calculated critical size of a nucleus and the observed size of grains that did not continue growing can be obtained if a reasonable correction is made in obtaining the energy of the surfaces of the subgrains. For example, since the sample is a single crystal with a cold-rolling reduction of 70 pct in thickness, one needs either an average disorientation for this or an average subgrain boundary energy rather than the 2.5 deg disorientation of a bent crystal, which was used by the author. From either the Laue photographs of the author or the pole density plot of Koh and Dunn 16 for a (113) [332] cold-rolled crystal the

Jan 1, 1961

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

By James E. Berryman

A method is presented for calculating the pressure depletion performance of a gas-condensate reservoir from the original reservoir fluid composition using the laboratory determined pressure-production history and retrograde liquid accumulation as guides. Equilibrium vaporization ratios for this calculation were modified from published data until the calculated dew point pressure and retrograde liquid accumulation agreed with the values observed in the laboratory. The calculated results are compared with the produced gas composition determined by low temperature analysis during constant volume laboratory experiments of pressure depletion behavior. This comparison shows that the calculation procedure is adequate for determination of gas phase composition. Data from field separation tests in low temperature separators are presented which verify the applicability of published equilibrium vaporization ratios for a wide range of separator conditions. INTRODUCTION A reliable prediction of the pressure depletion performance of a gas-condensate reservoir is necessary in determining reserves and evaluating field separation methods. The predicted performance is also used in planning future operations and studying the economics of projects for increasing liquid recovery. Because the flow of fluid in a volumetric gas-condensate reservoir is usually single phase flow, the pressure-depletion per-formake is primarily a function of the phase behavior of the reservoir fluid. The properties of a gas-condensate system of major importance are: (1) compressibility factor at reservoir temperature and pressure; (2) dew point pressure; (3) composition changes of the vapor phase with pressure depletion; (4) recovery of original in-place hydrocarbons at any pressure; and (5) retrograde condensate accumulation. These properties are most generally determined by a pressure depletion-type experiment on recombined separator gas and liquid samples in the laboratory. ldeally the pressure-depletion performance can be calculated from the composition of the original reservoir fluid if the reservoir temperature and initial pressure are known.1,2,3 It has been reported "... comparison of such computations with depletion-type ex-periments on recombined samples in the laboratory have yielded results that appeared to be entirely adequate.". The success of such calculations is determined by the equilibrium vaporization ratios chosen, especially those for the higher boiling point hydrocarbons. It is the purpose of this paper to present a method for computing the change in composition of the vapor phase during pressure depletion by production using laboratory determined properties of the system to guide the calculation and to illustrate the use of the method with data from the Cockfield "D" sand of Washington field, St. Landry Parish, La. Results of field tests and laboratory analysis are included. As a result of this reservoir fluid study, a cycling program has been evaluated, the fidd has been unitized, and the cycling started in July, 1956.

Jan 1, 1958

By H. P. Allen

THE chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 tons of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others.

Jan 8, 1925

By S. F. Emmons

It was said by many who discussed Professor Posepny's admirable paper on the "Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the " vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of

Jan 1, 1901

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates' in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968