Search Documents

By John Porter

THE requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet process and the dry.

Jan 1, 1925

By F. W. Gordon

THE Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three, main stages of development in the accompanying drawings. Fig. 1 is the stove of 1869, the, year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the-cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrate the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down. between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the. restricted area of the passages and the many reversals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28' 6'". Another reason was that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22' X 28 1/2' stove held the field for several years. A slight change made from this was to the 18' X 40' stove, where the height was increased, but the number of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little less it was not any better. The next important change, seen in Fig. 2, was by increasing the height to 60 feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decreased by alternating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfaction, but; although the proper doors were provided, it was very difficult to clean, owing to the long distance the scrapers had to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost without impairing in any yaw the

Jan 1, 1881

By F. W. Gordon

The Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three main stages of development in the accompnying drawings. Fig. 1 is the stove of 1869, the year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrake the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the restricted area of the passages and the many revervals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28' 6". Another reason mas that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22' X 28½' stove held the field for several yearn. A slight change made from this was to the 18' X 40' stove, where the height was increased, but the dumber of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little lea it was not any better. The next important change, seen in Fig. 2, was by increasing the height to GO feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decremed by alterllating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfactiou, but, although the proper doors were provided, it was very difticult to clean, owing to the long (distance the scrapers lid to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost mithotlt impairing in any yaw the

Jan 1, 1881

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4'5 dense patches or clusters of prismatic dislocation loops, planar arrays,4'10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10' life level the

Jan 1, 1969

By Robert Keeney

THE electric smelting of manganese ore and the production of ferro- manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production. was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic-ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 1,4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese ore in the electric furnace during the war and in 1920 are listed in Tabled. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferro-manganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the, price of. ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 2, 1921

By George A. Packard

The experiments here described were made under my supervision while temporarily acting as head of the Department of Metallurgy at the Missouri School of Mines, at Rolla. The work was done by Messrs. W. E. Brown, W. C. Richards, and F. L. L. Wilson, and the description of the results forms a portion of a thesis presented for the degree of Bachelor of Science. These results are submitted because I have seen no description of the application of pot-roasting to the treatment of a copper-concentrate. This work followed that already described in the discussion of the Lime-Roasting of a Galena-Concentrate,' and was similarly occasioned by the lack of a furnace of the reverberatory type in which the copper-concentrates could be smelted. The material for the tests was a mixture of three lots available. The first consisted of 8-mm. ,jig-concentrates and the second of 0.5-mm. table-concentrates, from the San Juan district, Colo. Both contained pyrite, chalcopyrite, and galena. The third was a lot of copper-ore, found in the laboratory, which had been crushed through 8-mm. screen, and had at some previous time, before the laboratory roasting-furnace was torn down, received a partial roasting. The analyses of these ores are given in Table I. In order to determine the applicability of pot-roasting as to each lot of ore, and the effect of varying proportions of lime, six preliminary tests were made in a " size N " Battersea crucible, 9 in. high by 6 in. in diameter at top, with a 5/8-in. hole bored through the bottom. The crucible was set in the upturned elbow of a 2-in. pipe, the joint being luted with clay; and air was obtained from a receiver supplied by a compressor. The

Jan 1, 1908

Jan 1, 1966

By Noah Fields Drake

During July and August, 1899, the writer took advantage of an opportunity of going to Shansi to gather some information concerning the geology and value of the already famous coalfields of that province. The long journey, mainly on slow river-boats, and the limited time at command, allowed only about ten days of work to be done in the coal-fields around Tsê Chou. The geologic structure and the rock-formations were found to be simple and quite regular, so that in that time the accompanying sketch-map (Pig. 1) was made, and a fairly good idea of the distribution of the coal and general geologic features was obtained. The map was made by measuring a base-line about three-quarters of a mile long, triangulating for principal points over the field, and filling in the details by rapid sketches. The few elevations marked on the map were taken with an aneroid barometer. Only a few of the great number of towns and villages that are within this densely populated area are shown; and the coal-mines indicated are not the only ones within the area, but the ones where most of the following information about the coal was obtained. The value of this coal-field was first clearly set before the scientific and commercial world by Baron von Richthofen,* who made a geologic reconnaissance of Shansi in 1870. Since that time the hostile attitude of the Chinese government and people towards foreigners and their enterprises has kept the coal-fields from being developed. But the last few years of rapid change in the conditions of China have at last apparently opened a way for the exploitation of this coal-field. The Peking syndicate, a joint English-Italian company, now has concessions from

Jan 1, 1901

Jan 1, 1985

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By Lovell Lawrence

MAGNETITE deposits in the Eastern States have been mined uninterruptedly since pre-Revolutionary War days. The industry, thriving in normal times, was given impetus in all periods of tumult, and continued to advance and expand, until the Lake Superior ores came into production. A period of comparative quiet existed until increased freight rates, together with increased mining costs on Lake Region ores, permitted the magnetites again to compete. This, coupled with World War demands, created unpre¬cedented activity. Producing plants were at their peak, new mines were equipped and put in operation and the industry pushed production beyond the absorption point. Ore stocks were tremendous, internal competition severe, and a great increase in import of European ores brought the industry to a low ebb in 1923.

Jan 1, 1933

By E. T. Turkdogan, L. S. Darken

Calcium ferrite melts were equilibrated with sulfur and oxygen-bearing gases at temperatures within the range 1290°C to 1620°C. The results show that at oxygen partial pressures below 10-4 atm the sulfide-reaction occurs and at higher oxygen pressures the sulfur dissolves in the melt principally as sulfate ion. It is also observed that when the product increases, sulfate ions are converted to pyrosulfate ions and the results permit the evaluation of the pyrosulfate/sulfate ratio. It is shown that the ratio y CaSO,/rCaO increases with decreasing concentration of calcium oxide in calcium ferrite, silicate and aluminate melts. Indications are that oxy-acids, e.g. silica, alumina and ferric oxide, increase yCaS0,. A few experiments were carried out within the sul-tide range and the results are in accord with those obtained by other investigators on aluminate and silicate melts. BECAUSE of the industrial importance and theoretical interest, many investigators have studied the reactions between molten oxides, silicates or alumi-nates, and gases containing oxygen and sulfur. The early work reviewed by Schenckl and studies made by Bardenheuer and Geller2 indicates that solution of gaseous sulfur in an oxide melt resulted in the replacement of the oxide ions by the sulfide ions. Measurements made by Grant and Chipman3 on the equilibrium partition of sulfur between molten iron and complex silicate melts also demonstrated that, for a given temperature and silicate composition, the distribution of sulfur between slag and metal increased with decreasing oxygen content of the metal. Fincham and Richardson4 studied the effects of temperature and partial pressures of sulfur and oxygen on the solubility of sulfur in simple silicate and alumino-silicate melts. They observed that at oxygen partial pressures below about 10-5 atm sulfur in the gas dissolved in the melt as sulfide ions, replacing an equal number of oxide ions of the melt. At oxygen partial pressures higher than 10-3 atm, sulfur entered the melt as sulfate ions. Similar studies were made by St. Pierre and Chipman5 using calcium ferrite and calcium silico-ferrite melts. The experimental data presented in this paper were obtained in this Laboratory about 10 years ago; this is the first formal presentation although a preliminary report was given previously.6 In each of these experiments, a pure synthetic CaO-Fe2O3 melt in a platinum crucible was equilibrated with a gas mixture (SO2-O2, SO,-air, SO2-CO, or SO2-CO2-CO) at a temperature ranging from 1296°to 1620°C. The experimental technique was essentially the same as that reported by Darken and Gurry,7 the main difference being that the atmosphere in the reaction chamber contained sulfur dioxide together with oxygen, or carbon dioxide-carbon monoxide

Jan 1, 1962

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By C. B. Alcock, R. A. Oriani

Some simple models of solutions are described; these include the regular solution, the subregular solution, and the quasichemical model. The assunzption underlying these models, the physical signzficance thereof, and the experimental manifestations are discussed. Examples are presented from the fields of liquid and solid metallic solutions, liquid slags, mattes, liquid and solid ionic solutions, and mixed carbides to show under what conditions and for which systems these solution models are fair descriptions. The deviations of real solutions from the models are of theoretical interest. Some such deviations, both for dilute and for concentrated solutions, arc pointed out and their Physical sigtzzficance discussed. DURING the past half century there has been a gradual accumulation of thermodynamic data for systems of interest to the metallurgist. There remain many gaps in the data, however, and the metallurgist must often face the problem of estimation of thermodynamic quantities where measured values do not exist. One might hope that the experimental progress would be matched by theoretical advances which would make such estimations possible with a high degree of confidence. However, theoretical progress has been disappointingly slow even for the simplest kinds of solutions, and since the multicomponent systems in which the metallurgist is interested are very complex, one cannot expect theory to be of much help to the metallurgist. In this situation, therefore, it seems worthwhile to examine some simple models of solutions from two points of view: firstly, to see if such crude models represent the thermodynamic facts in as many types of solutions as possible sufficiently well for the needs of the metallurgist, and secondly to see what the deviations from such models show to be important for consideration by theorists. BOND ENERGY MODELS OF SOLUTIONS The simple models that we will examine from these points of view may be termed statistical models, in that they are concerned with the thermodynamic consequences of some simple assumptions about the energy of an assembly of atoms, molecules, or ions, and do not inquire into the physical basis of the interaction. The underlying assumption of these models is that the energy of an assembly of molecules (by which we include also atoms or ions) is given by the sum over all interaction energies of molecules taken two at a time; we will discuss only those models in which the pairwise interactions are restricted to those between nearest neighbors. Thus, in a pure substance of bond energy EAA, the internal energy (with respect to some specific reference state) will be expressed as NAA EAA where NAA is the number of nearest-neighbor pairs. A solution of molecules A and B will be characterized by NAA EAA + NBB EBB + NAB EAB where the Eij represent the bond energies of the nearest-neighbor i-j pairs. If one assumes that the EAA and EBB are the same in the pure components as in the solution, and that the coordination numbers in the two pure substances and in the solution are the same, then the energy of the solution with respect to the pure components (i.e., the energy of solution) is a function of the following linear combination of the bond energies: EAB - 1/2(EAA +EBB) = w. The thermodynamically ideal solution is defined as one in which the activity of each component is equal to the mole fraction of that component at all concentrations and all temperatures. It follows that

Jan 1, 1962

By J. M. Avasthi

The DOE-funded (Contract No. DE-ACO3-77ET13108) Gulf Research & Development Co. (GR&DC) field tests of underground coal gasification in steeply dipping beds (UCG/SDB) were conducted in the North Knobs area, located 12.8 km (8 miles) west of Rawlins, WY. The site has a gently rolling, sparsely vegetated, semidesert terrain on the transition zone between a broad, flat basin (Great Divide Basin) to the west and the subdued mountains of the Rawlins uplift to the east. A comprehensive geotechnical program (Ahner et al., 1980) was essential to successfully complete the test program. Emphasis of the program was the subsurface characterization of the site and consisted of mapping, drilling and logging, core analyses, and hydrologic tests. The samples of lithologic units over- and underlying the G coal seam were tested in the laboratory for their modulus and strength. This program provided the required data necessary for designing surface facilities, input for permits, and ensuring correct placement of the process modules. The two UCG tests at the Rawlins site were conducted in the nominally 6.7 m (22 ft) thick G coal seam (rank-subbituminous B), dipping at 63°.

Jan 1, 1984

Jan 1, 1894

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By Nev A. Gokcen

DISCREPANCIES and scattering in the equilibrium data on the reactions of hydrogen, and CO with dissolved oxygen in liquid iron are un- duly large. Available experimental results on the reduction of liquid ferrous oxide, i.e., wüs-tite, with hydrogen and CO are questionable, as pointed Out by Darken and Gurry'l Direct determinations of the solubility of oxygen in liquid iron are subject to errors which cannot be easily reduced by further experimental refinements, and therefore an accurate but indirect method is highly desirable. The purpose of this investigation was, therefore, 1)

Jan 1, 1957