Search Documents

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

By K. J. Anusavice, R. T. DeHoff, H. Oikawa, J. J. Pinajian

STUDIES of nickel self-diffusion and impurity diffusion in pure metals and alloys have, for the past two decades, employed predominantly the nickel radio-However, because of the low energy of the emitted particle, careful and time-consuming techniques must be used to obtain reproducible measurements. In our studies of nickel diffusion into copper, we have recently used Ni66 [Td1/2: 55 hr; : 0.20 Mev (100 pet)] which decays to it much more suitable as a tracer because of the presence of the high-energy y radiation from the cu66 daughter. Although the half-life of Ni66 is appreciably shorter than that of Ni63, the useful working lifetime of a small quantity, " 10 mc, is about 1 month. preparation bf Ni66. he Nis6 radioisotope was produced at Oak Ridge National Laboratory by means of a double (n,y) reaction:

Jan 1, 1969

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by . Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization with additional data will be completed in the near future by the writers.

Jan 1, 1935

By E. J. McCaustland

The behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The " tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32" F. is not so well known. Tests made by Prof. E. G. Coker, at McGill University,' show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of some investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

Jan 1, 1907

By Charles E. W. Bateson

The Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low range of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. Climate and VEgetation. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera ture is generally from 60" to 70" F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100" F. in the day-time, while 115" F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1907

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

A filled stope is one in which the support for walls and men and, at times, for the back of ore, is furnished by waste rock or sand tailings. The filling may be rock sorted out in the stope or from the walls, develop-ent, or the surface. The orebody is mined in sections, each practically an open or timbered stope, filled wholly or in part before adjacent ground is attacked. As a rule, the filled-stope method is limited to overhand flat-back, stepped-face, or rill stopes. The examples given are Copper Range, Iron Cap, Verde district, Zaruma district, Lucky Tiger, and Silver King Coalition.

Jan 1, 1925

By Harvey T. Kennedy, Charles R. Olson

In many investigations of the performance of petroleum reservoirs the assumption is made that the liquid, if below its bubble-point pressure, is at all times in equilibrium with gas. On the other hand, observations by numerous investigators have indicated that gas-liquid systems including hydrocarbon systems, may exhibit supersaturation to the extent of many hundred psi in the laboratory. Up to the present, there has been no reliable data on which ti judge the actual extent of supersaturation under conditions approaching those existing in petroleum reservoirs. The work reported here deals with observations and measurements on mixtures of methane and kerosene in the presence of silica and calcite crystals. Bubbles were observed to form on crystal-hydrocarbon surfaces in preference to the glass-hydrocarbon interface or to the body of the liquid. Statistically, it was found that the number of bubbles formed per second per square centimeter of crystal surface was a function of the supersaturation only. and the function was evaluated graphically. Supersaturations were observed up to 770 psi, under which condition bubbles formed quickly and with considerable violence. With decreasing degrees of supersaturation, the frequency of bubble formation became less, until at 30 psi supersaturation and lower, no bubbles were observed to form, even though the observation at 30 psi was continued for 138 hours. It was found that silica and calcite crystals had identical effects, within experimental error, in accelerating the formation of bubbles, and that small amounts of water and crude oil had no effect on the results. It is shown that the maximum supersaturation that can exist in a reservoir may be calculated from the data presented and from the area of the rock surface. It is also shown that the number of bubbles formed in the reservoir, in order of magni- tude, may be calculated for any rate of pressure decline imposed on the reservoir by production. The bearing of the number and distribution of bubbles on reservoir performance is discussed. INTRODUCTION A liquid system is supersaturated with gas when the amount of gas dissolved exceeds that corresponding to equilibrium at the existing pressure and temperature. The degree of super-saturation may be conveniently expressed as the difference between the bubble-point of the mixture and the prevailing pressure. Thus, if a mixture having a bubble-point of 1,000 psi at a given temperature exists in single liquid phase at 700 psi at the same temperature. it is supersaturated to the extent of 300 psi. There are many examples of high supersaturations, mostly in aqueous solutions, reported in the literature. Thus, Kenrick, Wismer and Wyatt1 showed that water may be saturated with oxygen, nitrogen or carbon dioxide at 100 atmospheres, and the pressure reduced to one atmosphere without producing bubbles immediately. When liquids are in a state of tension, they may be considered as supersaturated at least to the extent of the tension. The tensile strength of water has been reported as 30 atmospheres by Meyer,1 60 atmospheres bv Budgett. 30 to 50 atmospheres by Temperley and Chambers,4,5 200 atmospheres by Dixon6. and 223 atmospheres by Briggs.7 Vincent8,9 determined the tensile strength of a mineral oil as 45 psi. Gardescu1 maintained pressures for short times in a model reservoir at 115 psi below the bubble-point. It should be noted that the high supersaturations observed were obtained on systems carefully purified to remove particles or surfaces which might promote the formation of bubble; These "nuclei" were considered as contaminants which interfered with the determination of a property of the liquid. In

Jan 1, 1952

By Homer W. Riley, C S. Jenkins

SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron- plates, .broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, [ ] into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tool design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls. Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, there- fore, of slow-speed, compound geared rolls, especially for breaking the

Jan 1, 1943

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the hest of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but call vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no imrncdiate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By E. A. Gulbransen, K. F. Andrew

The gas-metal reactions of zirconium are very interesting. The metal is extremely stable at room temperature to reactions with the several gases present in air and the metal will stay bright indefinitely. However, at temperatures of several hundred degrees higher the metal reacts readily with oxygen, nitrogen and hydrogen. This behavior, in addition to the fact that zirconium is one of the higher melting point metals which might have high temperature applications under the proper conditions, resulted in the work reported in this communication. There are several factors which indicate that zirconium might have good oxidation resistance at elevated temperatures. These are: (1) the high melting point of approximately 1860°C, (2) the high melting point of the oxide of approximately 2675°C, (3) the high degree of thermodynamic stability of the oxide to chemical reaction and the low decomposition pressure of the oxide and (4) the possible formation of a continuous oxide film since the volume ratio of oxide to metal is greater than unity. The unfavorable factors are: (1) the metal reacts to form nitrides, hydrides and carbides, (2) the oxide is soluble at elevated temperatures in the metal and (3) the oxide ZrO2 undergoes crystal structure transformations at high temperature. The oxidation resistance of this metal is not only a question of the rate of film formation but is complicated by the fact that the oxide and other reaction products dissolve in the metal which in turn will affect the physical and mechanical properties of the metal. The protection of the metal to nitride formation must be considered separately from the oxide problem. One unfavorable factor is that the volume ratio of the nitride to the metal is about unity. This indicates that a discontinuous film might be formed. This paper will present measurements on the rates of reaction of the metal with O2, H2 and N2 over a wide temperature and pressure range. The reaction in high vacuum and the stability of the several compounds formed will be presented. The results are correlated with fundamental rate theory and with the physical and chemical structure of the metal and film. Literature Although many papers have been published on the chemical reactions of zirconium with various gases, comparatively few are concerned with the protective nature of the metal and its reactions at normal pressures. The studies in the pressure range below 0.01 mm of Hg gas pressure are largely of interest in the nature of the adsorption of gases by hot filaments in high vacuum apparatus. The reactions of zirconium in this pressure range have been reviewed by Fast8 and by RaynOr.27 In spite of certain differences of opinion as to the maximum adsorption temperatures for various gases, the low pressure range is qualitatively understood. Some of these papers will be mentioned briefly here. 1. LOW PRESSURE Ehrke and Slack' find that oxygen reacts above 885°C and hydrogen above 760°C. Nitrogen does not react up to a temperature of 1527°C. Fast9 on the other hand observes that oxygen is absorbed above 700°C and nitrogen at temperatures exceeding 1000°C. Hydrogen is absorbed from 300" to 400°C and liberated between 500" and 800°C. It is readsorbed at 862°C and released above 862°C. Hukagawa and Nambo22 find a rather complicated picture for the absorption of oxygen. A rapid initial absorption is found between 180" to 230°C. Further oxygen is not taken up until a temperature of 450°C is reached. The optimum temperature for complete absorption is 650" to 700°C. Nitrogen is found to be completely adsorbed at 600°C. However some of the gas is evolved at higher temperatures. Their data on the absorption of hydrogen indicate some of the gas is removed at 550°C. Guldner and Wooten17 in a study of the low pressure reactions of zirconium with various gases observed that the reaction with oxygen occurs at temperatures above 400°C and that the oxide is formed. The reactions with carbon monoxide and carbon dioxide occur rapidly at temperatures of about 800°C with the oxide and carbide being formed. Zirconium reacts at temperatures of 400°C slowly and at 800°C rapidly to form the nitride and with hydrogen and water at 300°C to form the hydride and a mixture of the oxide and hydride respectively. 2. NORMAL PRESSURE DeBoer and Fast3 in a study of the electrolysis of oxygen in zirconium find that the metal absorbs up to 40 at. pct of oxygen without forming a new phase. The solubility of nitrogen in the lattice has been studied by de Boer and Fast4 and Fast10 and is found to be considerable. At higher temperatures the oxide dissolves in the lattice at an appreciable rate according to Fast10 and the zirconium surface becomes active. De Boer and Fast4 and Hägg18 have studied the solubility of hydrogen and find that at room temperature the solubility corresponds to ZrH1.95 Desorption occurs on lowering the pressure. Hydrogen is stated to be more soluble in the ß-form and the

Jan 1, 1950

By K. A. Johnson, H. F. Yancey

Physical properties have been used for a long time in characterizing different kinds of coal, and such physical properties as friability and slacking have been included along with chemical properties in grouping coals according to the widely used system of classification adopted by the U. S. Geological Survey. Nevertheless, the usefulness of physical properties for classifying the different ranks or kinds of coal has been limited because it has not been possible to express these properties in definite form as numerical values. Because of the present wide interest in the formulation and adoption of a satisfactory system of coal classification, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the College of Mines of the University of Washington, has recently completed a study of the physical and chemical properties of approximately 100 different coals ranging in rank from lignite to anthracite. Purpose and Scope For this investigation samples were collected in approximately 45 mines and prospects in Washington and 23 mines in other states. The following studies, in addition to proximate and ultimate analyses, were made of the samples: Determination of (1) friability, (2) slacking or weathering characteristics, (3) yield of products by low-temperature carbonization in a laboratory retort, and (4) agglutinating value. Most of the coals examined were subjected to each of the tests enumerated, but with coal of some ranks this was unnecessary in some instances, and in others it was not feasible to do the work involved. A report which includes the analyses of the coals and the details of the methods of examination used in the investigation is being published by the Bureau of Mines.' It is the purpose of the present report to show the results of the friability, slacking, low-temperature and agglu-

Jan 1, 1932

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953

By Martin A. Moyers

THE nation's effort to win the war speedily is reflected in current trends in coal utilization, as in all other fields of our lives. In all industries, wherever coal is used for the production of heat and power the emphasis is on getting the most useful result with the least expenditure of matt.ria1. In addition to carrying its own share of the load, increased as it is by the demands of war industry, coal has had to fill in for the other fuels, mainly petroleum products, whose distribution from their more distant sources has been crippled by lack of shipping. Thus, the outstanding note in the utilization of coal this year is not the development of new methods of burning or handling coal but the extraordinary job that the industry has done in producing enough coal to serve all needs.

Jan 1, 1943

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer' up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der' found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.'' APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

F. L. Clerc, Chicago, Ill. (communication to the Secretary): On page 681 in Mr. Winslow's paper, he refers to me as having "advocated the view that the ores were derived from the patches of Coal-

Jan 1, 1895