Search Documents

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.' Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960

By George B. Lee

During the two years in which the new reduction-works of the Copper Queen Consolidated Mining Co. have been in operation at Douglas, Ariz., there has developed a remarkable condition in regard to the corrosive action of the water used to cool the jackets of the blast-furnaces. Were it not for the many contradictory features, it might pass as one of the unavoidable troubles due to the composition of the water. This water, obtained from wells 600 ft. deep, is also used in the steam-boilers, and its composition, as shown by the following analysis, does not indicate the presence of any ingredient which would explain the corrosion: Grains Per U. S. Gal. Silica,...........0.861 Iron oxide and alumina,....... 0.223 Calcium carbonate,....... 0.261 Calcium sulphate,................. Magnesium carbonate,........... Sodium and potassium sulphates,..14.850 Sodium and potassium chlorides,.9.732 Sodium and potassium carbonate, . 6.482 32.409 The jackets are made of inner plates 0.5 in. thick and an outer plate # in. thick, with 3/8-in. stiffeners between the inner and outer plates. In from 10 to 12 months the inner plates have been reduced by corrosion to a thickness of from + to & in., while the outer plate in the same time is reduced by less than 1/16 in., and the stiffeners show very little corrosion. The plates are pitted and eaten away in some places more than in others. There is practically no scale found on the jackets, but when cleaned considerable iron oxide is found in the bottoms. With an action so marked, serious trouble would be expected in the boilers, but, on the contrary, a recent inspection by a

Jan 1, 1908

By Nicholas J. Grant, Michio Yamazaki

Cast copper alloys containing 10, 20, and 30 pct Ni and 0.75 to 0.80 pct Al were machine-milled into chips, then comminuted in a rod mill to fine flake powder utilizing a number of processing variables. The powders here internally oxidized, mostly at 800°C, in a low-pressure oxygen atmosphere. The consolidated powders were hot-extruded into bar stock. Room-tenmperature tension tests, stress-rupture tests mostly at 650°C, but also at 450° and 850°C, and hardness measurements after various annealing temperature treatments to study alloy stability were perfomted. Excellent room-temperature strength, high rupture strength at 650°C, and resistance to recrystallization at 1050°C were obtained. Problems in optimizing conditions for internal oxidation of Cu-Ni base alloys are discussed. THE interesting high-temperature properties of SAP' have stimulated considerable effort in the study of more refractory alloy systems where the potential for high-strength alloys at high temperature is great.2-13 A number of methods have been utilized to produce the desired fine, hard particle dispersions, of which internal oxidation2,9,7 of dilute solid-solution systems offers considerable promise by virtue of the potential for producing ultrafine, well-dispersed oxides. While most of the published works are concerned with pure metal matrices, a number of investigators have studied the effects of solid-solution strengthening.10,19 Use of more complex alloy matrices (for example, aging systems) has been unsuccessful because overaging still occurs at high temperatures in the oxide-containing alloys.14.15 Solid-solution strengthening is, however, effective at very high temperatures9,10 and might be expected to contribute importantly to the strength of oxide-dispersion strengthened alloys. For this study, internal oxidation of solid-solution alloys of copper and nickel, containing small amounts of aluminum, was chosen as the method of alloy preparation. PREPARATION OF ALLOYS Three copper alloys containing about 10, 20, and 30 pct Ni and each containing 0.75 to 0.80 pct A1 (enough to yield about 3.5 vol pct alumina) were prepared as air-cast ingots measuring 2.5 in. diameter by 6 in. high (see Table I for the analyses). Processing steps for all the alloys were as follows (also see Table 11): 1) Homogenization of the ingot at 982°C (1800°F) for 45 hr in an argon atmosphere. 2) Machine milling of ingots into fine chips. Average thickness was about 0.1 to 0.2 mm. 3) Hydrogen reduction of chips at 593°C (1100° F) for 1 hr to reduce copper and nickel oxides. 4) Rod milling of chips to finer powders. 5) Hydrogen treatment of powders as in step 3. 6) Internal oxidation of the powders. 7) Hydrogen treatment of oxidized powders as in step 3. 8) Hydrostatic compression of evacuated powders. 9) Sintering of compacts in hydrogen. 10) Hot extrusion. Variations in processing among the alloys were made in steps 4, 5, and 10 (see Table 11). In the past, two methods were utilized to internally oxidize alloy powders. Preston and Grant3 surface-oxidized dilute Cu-Al powders to obtain the necessary amount of oxygen to oxidize the solute metal (aluminum and silicon), and then permitted the formed copper oxide to diffuse and react with the solute in an argon atmosphere. Bonis and Grant4 exposed Ni-A1 and other nickel alloys to an oxygen pressure derived from the decomposition of nickel oxide at a preselected temperature, in an argon atmosphere. Both methods are applicable and can be modified to generate a range of oxygen pressures for oxidation of the solute but not the solvent metals. Procedure I: Surface Oxidation of Alloy A3, Cu-10Ni-0.76A1. Powders of -20 to +28 mesh were surface-oxidized at 500°C (932°F) to obtain the desired amount of oxygen for oxidation of the aluminum to alumina; the powder was then sealed in Vycor and heated at 900°C (1652°F) for various times up to

Jan 1, 1965

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

By L. S. Austin

Our SUCCESSFUL plants in the West were at first erected on a small scale, and as their business has been built up, have been added to gradually as their limitations permitted. They have had to adapt themselves later to their circumetances, making the best of drawbacks, and putting up with much which, had it been originally allowed for, would not now impede them.

Jan 1, 1897

By Charles W. Goodale

The ores of the Butte district present a variety of combinations, and their treatment by concentration is an interesting study. They may be classified in general as follows: 1. Copper-silver ores, which are produced by the mines of the Anaconda group, and by the Mountain View, Colusa, Silver Bow and Parrot. The high-grade ores from these properties are roasted and then smelted; but a large proportion of the output is low-grade and siliceous, and hence requires concentration. The copper-bearing minerals are chalcocite, bornite, enargite and chalcopyrite, in varying proportions in the different mines, the gangue, which breaks readily into grains, being quartz and feldspar. 2. Silver-copper ores, of which the Gagnon vein is the largest producer. The grade of the ores from this mine is such that nine-tenths of the output requires concentration. The silver- and copper-bearing minerals of this vein are massive wurtzite, sphalerite, bornite, chalcopyrite, pyrite, tetrahedrite, enargite, tennantite and galenite, with a quartz gangue associated with feldspar and small quantities of barite and fluorite. The gangue is very hard and not at all granular. 3. Silver-ores containing a small amount of gold, embracing the product of the Alice, Magna Charta and Moulton claims, on what is known as the Rainbow lode, and that of the Lexington, Blue Bird, Nettie, Burlington and other mines. The gangue is quartz, carrying pyrite, sphalerite, galenite, tetrahedrite and argentite, with manganese in the form of rhodochrosite and rhodonite. Good results on ores of this class cannot be obtained by concentration, because large percentages of the silver-bearing minerals are disseminated through the gangue in such minute grains that even the finest practicable crushing

Jan 1, 1897

By Clarence E. Sims, George A. Moore

INTRODUCTION IN previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficient time is allowed. For precise work, the method claims preference because the equipment for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the transformation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approximately 2 hr. While it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual error may be more or less constant between samples. For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temperature process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and evolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1948

By Fred Wise, C. W. Wark

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. MILLING PRACTICE Crushing (Fig. 1).-There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. 1 shows the method and

Jan 1, 1940

By P. T. Gallagher, W. A. Oates, J. A. Lambert

FAIRLY extensive equilibrium data exists for carbon dissolved in r iron.1-8 However the temperature coefficients of the carbon activity, ac , are insufficierltly preciseto reveal whether the heat of solution of carbon, ?HC , varies with composition. It is doubtful

Jan 1, 1970

By Arthur Phillips, Carl H. Samans

The study of anisotropy in metals has been greatly stimulated in recent years by the rapid development of X-ray methods for determining the crystallographic relationships of wrought and annealed materials. Prior to this time the knowledge regarding the directional properties of commercial alloys consisted almost exclusively of observations of a practical nature made during the fabrication of metal objects, supplemented by a limited number of mechanical tests on specimens cut at various angles to the direction of working. Such observations clearly indicate that the common methods of cold-working metals cause both a crystallographic and a mechanical fibering varying in character and degree according to the nature and extent of the deforming process. Even after annealing, following certain not too well known combinations of reductions and anneals, a preferred orientation may exist,, thereby constituting a residual fiber effect sufficiently pronounced to manifest directional properties. With the application of the X-ray the experimental horizon was extended chiefly because the study of anisotropic metals promised to offer direct and quantitative evidence regarding the involved mechanism of fragmentation and plastic flow. As a natural consequence the intensive studies in this direction have yielded a vast accumulation of data of ultimate potential value. Unfortunately, however, as is commonly the case in entering a virgin field of experimentation, many of the data cannot be molded into complete and coherent form because of the many unrelated conditions of the experimental projects. Again, the results of the study of single crystals have been rather naturally but at times indiscriminately applied to poly crystalline metals. Furthermore, sweeping statements have been made regarding the behavior during working and annealing of metals and alloys, entirely on the basis of similarity in lattice arrangement. There is abundant reason for believing that relatively small concentration variables, differences in magnitude and distribution of applied stresses, and the character of associated annealing treatments may in some cases greatly influence the mechanics of flow

Jan 1, 1933

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

By W. B. HILLHOUSE

AN excerpt from the Alabama State Mining Law, pertaining to, transporting men' into and out of the mines, reads as follows: "A trip of empty cars may be operated for the purpose of taking employees into and out of the mine, where the distance to and from their work exceeds one mile." The State Mining Department of Alabama includes in its inspection the transportation of men into and out of the mines, also studying and noting improvements, or progress made, that would tend to create a greater assurance of safety in this practice. Everyone is familiar with the original safety methods employed in man-trip transportation, such as passing a rope around the trip of cars, or through the cars, fastened in the conventional manner, and with the usual "clog," commonly called a drag, on the rear end. Also there is a more advanced method of transporting men, such as the double-rope system, which is feasible on slopes used exclusively for this purpose, and is very satisfactory. However, for the past eighteen months; the Republic Steel Corp. and the Tennessee Coal, Iron & Railroad Co. have adopted a practice that shows

Jan 1, 1935

By G. K. Dumbauld, B. E. Morgan

A satisfactory well-cementing composition must retain its fluidity long enough to be pumped into Place; then it must develop within a reasonable length of time sufficient strength and impermeability to anchor the casing in position and to form an effective seal between the casing and the formations. These properties may be evaluated by pumpability, strength (compressive or tensile), and permeability tests. Laboratory test procedures for the determination of pumpability time and strength development have been outlined previously and are readily available,1 but a satisfactory and convenient laboratory procedure for the measurement of the permeability of set cement has not been developed heretofore. some permeability data have been obtained previously by passing air through dried cement specimens.2 such a procedure is unsatisfactory because the drying of set cement alters it physical and chemical properties and subjects it to conditions dissimilar to well conditions. A more realistic method would be one wherein the cement remains water-saturated durin

Jan 1, 1952

Jan 1, 1918

By Edward C. J. Urban

THE nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than to years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini¬tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. DEVELOPMENT OF ROCK DRILLS The earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its piston-type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1947

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1917

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923