Search Documents

By R. J. Burgess, A. R. Ramey, A. R. Adams

During interpretation of pressure buildup tests on gas wells in a tight dolomite gas reservoir, peculiar behavior was noticed. Two straight lines were apparent. Effective permeability to gas taken from either straight line was about the same, and the Miller-Dyes-Hutchinson dimensionless time check for the straight line was proper for both straight lines. Geological data indicated the likelihood of scattered trending fractures in the reservoirs. Since the first straight Iine yielded permeability values close to the geometric mean permeability from core analyses, it was postulated that the reservoir model was that of an acidized well completed in the tight dolomite, but that widely scattered hairline fractures caused the mean permeability of the reservoir distant from the well to be higher than the matrix permeability. Because all other studies of fractured reservoirs to the authors' knowledge assumed that the fracture matrix was dense enough to communicate directly with the well, no interpretative methods were available. The Hurst line-source solution for a radial change in permeability for interference between oil reservoirs was adapted to pressure buildup testing. The result indicated that the first straight line should yield the proper matrix permeability and wellbore skin effect. The second straight line may be extrapolated to obtain static pressure. The time of bend between the straight lines was used to estimate distance to a fracture. Application to field test data is shown. It is believed that the methods developed and the case history presented will add to present tools available for pressure buildup interpretation. Introduction Since the pioneer studies by Miller, Dyes, and Hutchin-son1 and Horner' in 1950 and 1951, well test analysis has become recognized as one of the most powerful tools available to both production and reservoir engineers. Well test analysis serves as a logical basis for well stimulation and completion analysis, and for long-term reservoir engineering. Since the early 19501s, much effort has been placed on the development of well-test analytical methods. Reservoir and well conditions of increasing complexity have been considered systematically to provide the analyst with a catalog of causes and effects. Matthews and Russella state that some 200 papers dealing with this subject have been published in the last 35 years. Developments in well test analysis appear to have originated in one of two ways. Either a physically realistic field condition was anticipated and analytical solutions for the condition achieved, or anomalous field test behavior was recognized and interpretative methods sought for the anomaly. In recent years, it has appeared that the latter has inspired an increasing number of studies. The analyst today finds an increasing number of known cause and effect studies available for well test analysis, the classic of which is that of finding the specific flow problem that generated the answer — the well behavior. Although it may be impossible to achieve this goal uniquely, the analyst often is able to select a useful interpretation that combines all known performance and geologic data — or to show that various logical alternatives would not significantly affect the interpretation. During a recent reservoir study, we observed gas well test behavior that did not appear to fit behavior described previously. Although it cannot be said that we have found a unique interpretation, we shall present in this paper the peculiar behavior observed, and describe the reservoir and interpretative methods developed. Reservoir Description The subject gas reservoir is a 9-mile-long, narrow dolomite reservoir lying within a limestone of Ordovician age. (See Fig. 1.) The dolomitized rock in the field consists of dark brown to buff, dense to coarsely crystalline, vugular dolomite containing numerous hairline fractures, many of which may have been closed in the reservoir and parted when cores were brought to the surface. Larger fractures are also apparent in core, but usually are filled and sealed with euhedral dolomite crystals. Portions of the north flank of the reservoir are known to be cut by a sealing fault downthrown to the north. Gas wells located near the fault have higher open flow potentials than those more distant from the fault. This is believed to be a result of higher permeability near the fault due to more extensive and open fractures. Detailed coring and core analysis have been performed on several of the wells in this reservoir. Fig. 2 presents permeability variation' plots for both horizontal and vertical

Jan 1, 1969

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 9, Article I, of the Bylaws of the Institute (see page 64 and following pages). During 1934, sundry amendments were made for the purpose of improving the student relationship. Postgraduate students are now eligible; and associateship can be maintained, with the payment of the regular dues of $2 per year, for 18 months following graduation in June. With his regular dues, each Student Associate is entitled to receive during the year his choice of MINING AND METALLURGY, METALS TECHNOLOGY, MINING TECHNOLOGY, PETROLEUM TECHNOLOGY, or two "classes" of Technical

Jan 1, 1943

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969

By R. G. Ward, D. R. Gaskell

Using the maximum bubble pressure technique, the densities of iron silicates at 1410°C have been measured blowing helium, nitrogen, and argon. By ensuring equilibrium between the melt and the blowing gas with respect to oxygen potential and by minimizing tempcrature cycling of the furnace, iron precipitation in the melt has been prevented. Thus the previously reported effect of blowing-gas composition on the densities of the melts has been eliminated. Consideration of the oxygen densities of the melts gives an indication of the structural changes accompanying composition change. The density-composition relationship of iron oxide-silica melts in contact with solid iron has been the subject of several investigations1-7 and considerable disparities exist among the various results obtained. Of these investigations, all except one5 have employed the maximum bubble pressure method. In the most recently reported of these investigations1 the density-composition relationship obtained blowing nitrogen differed from that obtained blowing argon. The measured densities obtained under nitrogen were greater than those obtained under argon, the difference being a maximum at the pure liquid iron oxide composition and decreasing with increasing silica content. This observation rationalized the disparities existing among the results of the earlier investigations, showing that two lines, one for nitrogen and the other for argon, could be drawn to fit all the earlier results. No explanation for this phenomenon could be offered. Chemical analysis of rapidly quenched samples of melt for dissolved nitrogen, and direct weighing measurements, excluded solution of nitrogen in the melt from being the cause of the increase in density. The range of blowing gases was extended by Ward and Hendersons who measured the density of liquid iron oxide bubbling helium, nitrogen, neon, argon, and krypton. The measured density was found to decrease smoothly with increasing atomic number of the bubbling gas. The work reported here is a continuation of the program initiated by Ward and Sachdev7 to study the densities in multicomponent melts in which the iron oxide-silica system is the solvent. As such it is necessary to explain or eliminate the anomalous densities of iron silicates under different atmospheres, and the present rede termination was carried out towards this end. EXPERIMENTAL The maximum bubble pressure method of density determination was again employed and the experimen- tal apparatus used was essentially the same as that used by Ward and Sachdev.7 A molybdenum-wound resistance furnace heated an ingot iron crucible of internal diameter 1 in. containing a 2-in. depth of melt. The bubbling gas was blown through a 1/4 -in.-diam mild steel tube onto the end of which was welded a 2-in. extension of 1/4 -in.-diam ingot iron rod, drilled out to 5/32 in., and chamfered to an angle of 45 deg. The blowing tube was introduced to the furnace through a sliding seal and its position was controlled by a vertically mounted micrometer screw which allowed the depth of immersion to be determined with an accuracy of ± 0.01 cm. A Pt/Pt-10 pct Rh thermocouple was located below the crucible and temperature control was effected initially by means of an on-off controller and later by a saturable core reactor. The bubble pressure was determined by measurement of a dibutyl phthalate manometer using a cathetometer. PREPARATION OF MATERIALS Iron oxide was produced by melting ferric oxide in an inductively heated iron crucible in air. The liquid was quenched by pouring onto an iron plate. Silica was prepared by dehydrating silicic acid at 650°C for 12 hr. RESULTS Before any measurements of the density of a melt were made, the density of distilled water at room temperature was measured bubbling helium and argon. Both gases gave the density as 1.00 ± 0.01 g per cu cm which showed that the density of the manometric fluid (dibutyl phthalate) was not affected by contact with the blowing gas. With the furnace controlled by an on-off temperature controller an attempt was made to measure the density of pure liquid iron oxide by bubbling argon. The furnace atmosphere gas and bubbling gas were dried over magnesium perchlorate and deoxidized over copper turnings at 600°C. It was found that the pressure required to blow a bubble at a given depth increased slowly with time, and thus it was impossible to obtain a unique value for the density of the melt. Inspection of the blowing tube after removal from the furnace showed that rings of dendritic iron had precipitated from the melt onto the immersed part of the tube. This is shown in Fig. l(a) where the various "steps" correspond to different depths of immersion. The precipitation of iron was considered to be due to one or both of two possible causes: i) The composition of the liquid iron oxide is that of the liquidus at the temperature under consideration and can be expressed by the equilibrium

Jan 1, 1968

By B. M. Larsen, T. E. Brower

An increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely, that which presumably is present in diffusible form in the solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent Oz in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By R. D. Young, E. A. Harre

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Certain bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent required by succeeding nonleguminous crops. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. These organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen at high temperatures and pressures and in the presence of a catalyst to form ammonia. Modern plants use air, water, and natural gas or other hydrogen sources to produce the ammonia that is now the key building block of the fixed nitrogen industry. Several major problems that developed in the 1970s continue with the nitrogen industry into the 1980s. These are (1) the continuing sharp escalation in the cost of feedstocks for ammonia production as well as all energy sources, and (2) the very steep increase in the investment cost of production facilities. More than 75% of the fixed nitrogen produced domestically is consumed as fertilizers. The types of materials used as fertilizers have changed significantly during the past years. There has been a trend from the use of low-analysis fertilizers to types which contain high percentages of plant nutrients. The average plant nutrient content (N + P2O5 + K2O) of fertilizers used in the United States has increased from 18% in 1930 to 32% in 1960 and today approaches an average of 44%. In the case of nitrogen fertilizers, the low analysis natural nitrates (16% N) gave way to ammonium sulfate (20% N) after about 1920. After World War II, ammonium nitrate (33.5% N) previously used in munitions, became established as the leading nitrogen fertilizer. Urea use as a fertilizer (46% N) began in the 1960s, and in the past 10 years has become the world's leading solid nitrogen fertilizer. Nitrogen Materials Anhydrous Ammonia-Anhydrous ammonia is a colorless gas at ambient temperatures and pressures and has a sharp pungent odor. Anhydrous ammonia is stored and transported as a liquid in high-pressure cylinders and tanks at ambient temperature, and in low-pressure tanks, barges, and ships at -28°F. Anhydrous ammonia is applied directly at 4 to 7-in. depths in the soil as a high-pressure liquid by special applicators, after which it expands to a gas that dissolves in the soil moisture or is absorbed on soil colloids. In other systems ammonia is metered into irrigation water and is thereby introduced into the soil.

Jan 1, 1983

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By W. F. Chiao

Ultrasonic attenuation, a, measurements in the frequency range of 5 to 55 mc per sec have been studied to determine their quantitative relationship with the following three variables of mixed microstructures in steels: 1) the volume percent, XF, of polygonal fer-rite in mixed structures of martensite and polygonal ferrite in Fe-Mo-B alloys: 2) volume percent, XA, of retained austenite plus martensite aggregates in high-carbon steel; and 3) substructural differences between 100 pct bainitic ferrite structures formed at various temperatures. The quantitative relationship obtained in the first two conditions by plotting a us the known structural parameters can be expressed, respectively, as: where al, a 2 and C1, Cz are constants. In the third condition the nature of the attenuation depends on the state of dislocations generated at the transformation temperatures and also on the alloy composition. From these measured results, the mechanism of ultrasonic attenuation caused by these mixed microstructures can also be studied. MUCH interest has recently been shown in the application of ultrasonic attenuation and wave velocity measurements to the study of the microstructural characteristics of steels. The general aims of most of the investigations in this field can be grouped into two categories: one is to study the mechanisms of ultrasonic losses caused by the characteristic phases in the microstructure of steel,''' and the other is to develop nondestructive test methods and applications for quality control.~' 4 Apparently no work has been done on the evaluation of ultrasonic attenuation meas -urements as a means of quantitative determination of a given phase in the microstructure of a steel. It is well-established that the decomposition of austenite results in four main microstructural constituents—polygonal ferrite, pearlite, bainite, and martensite—and that each phase has different mechanical properties. Thus, when a steel consists of mixed microstructures, the mechanical properties can often be related to a quantitative measure of the volume percent of each phase present. This study relates ultrasonic attenuation measurements to: 1) the volume percent of polygonal ferrite in mixtures of martensite and polygonal ferrite in Fe-Mo-B alloys; 2) the substructural differences between 100 pct bainitic ferrite structures formed at various temperatures; and 3) the vol- ume percent of austenite in austenite plus martensite aggregates in a high-carbon steel. The choice of the specimen materials was based on the laboratory stocks which were suitable to produce the required mixed microstructures for this study. EXPERIMENTAL PROCEDURES Materials and Heat Treatment. Polygonal Ferrite Plus Martensite Structures. This mixture of phases was produced in a vacuum-melted Fe-Mo-B alloy. The alloy was hammer-forged at 1900" ~ to a -f-in.-sq bar. By isothermally heat treating the alloy at 1300° F for various times and then water quenching, variations in the amount of polygonal (or proeutectoid) ferrite can be controlled in a microstructure in which the balance of the material is martensite. In the present work, four different times of isothermal transformation were adopted; after heat treatment, the four specimens were machined for ultrasonic measurements. The compositions, heat treatments, and dimensions of the four specimens are listed in Table I. 100 pct Bainite Structures Formed at Different Temperatures. It has been well-established by Irvine et al.= that the presence of molybdenum and boron in ferrous alloys can retard the formation of polygonal proeutectoid ferrite and expose the bainitic transformation bay, so that a more acicular or bainitic ferrite can be obtained over a wide range of cooling rates. Their investigation6 also showed that the mechanical properties of fully bainitic steels are usually closely dependent on the substructural characteristics of the steels. For studying the substructural characteristics in completely bainitic structures, six Fe-Ni-Mo alloys, of which five were free from carbon addition and one with 0.055 pct C addition, were selected so that a wide range of hardness values for 100 pct bainitic ferrite structures could be produced by normalizing at 1900" F followed by air cooling. The different bainitic transformation temperatures were recorded during air cooling. All of the alloys were vacuum-melted and then forged at 1900" F to square bars. Data on the six specimens of these structure series are summarized in Table 11. Austenite Plus Martensite Structures. The high-carbon steel used to study austenite plus martensite structures was vacuum-melted and then forged into Q-in.-sq bar. The series of mixed structures of austenite plus martensite was produced by quenching the specimens from the austenitizing temperature to room temperature and then refrigerating them at various temperatures within the range of martensite transformation to produce different amounts of retained austenite. Data on the four specimens of this series are listed in Table 111. Quantitative Analysis of the Microstructures. The microstructures containing martensite plus polygonal ferrite were analyzed by the point-counting technique.

Jan 1, 1969

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By J. A. Herbst, O. A. Bascur

Fine coal cleaning by froth flotation has become common practice in the US with more than 73 kt/d (80,000 stpd) treated in this way. In spite of this large tonnage, developments in the automated control of coal flotation circuits have lagged significantly behind those for mineral systems. The primary reason is that instruments have not been available for the online measurement of carbon ash content or other critical variables in coal slurries. A second reason is that the influence operating variables have on coal flotation are not completely understood. During the last few years, some of the needed instrumentation has been developed, while an improved knowledge of the flotation process itself has occurred through mathematical modeling. As a result, certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, Dynafloat. After construction of a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables were analyzed. To develop combined grade and recovery control strategies, it was necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known, final, feasible grade/recovery operating conditions. Finally, an advanced strategy that uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1986

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By completing a double-track railroad cut-off, involving a large volume of cut and fill, in addition to a half-mile bridge spanning an important French river, engineers in the zone of the Services of Supply have opened up a route by means of which hours of valuable time are being saved in transporting men and materials to combat areas. Its most valuable feature is that it provides a means for by-passing a certain city where several, French railroad lines converge and where, consequently, congestion of traffic has been responsible for delayed train movements. To avoid a double-track turnout, which would have involved a cross-over cutting one of the French tracks, the two track connections of the cut-off are taken off from opposite sides of the French right-of-way. This involved running one of the new lines of the cut-off out from the main line track on a fill to a point where it could be brought back and over the French track on a steel girder bridge. Beyond this bridge the two tracks of the cut-off converge and straighten out in the standard type of double-track construction. The new cut-off is about 5 3/4 mi. (9 km.) long and has required 160,000 cu. yd. of cut (122,329 cu. m.) and 414,000 cu. yd. (316,527 cu. m.) of fill. In the biggest continuous fill a-yardage of 180,000 has been placed; the road-bed in this section-being-about 40-ft. (12 m.) above the original ground surface. The bridge portion of the cut-off, 2190 ft. (667.5 in.) long, is made up of ninety-nine 14-ft. (4.3 m.) timber spans and sixteen 50-ft. (15.3 m.) steel girder spans. This is the longest bridge which engineers of the American Expeditionary Forces have built in France. The timber spans are supported by pile trestle bents, while the longer steel girders rest on clusters of 43 piles. Two pile drivers of the steam-hammer type worked from each -end of the bridge toward the center of the river, while a drop hammer worked westward from the shore end. In this structure nearly two thousand piles 50 ft. or so in length had to be driven.

Jan 12, 1918

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By B. L. Landrum, J. Simmons, J. M. Pinson, P. B. Crawford

Patentiometric model data have been obtained to estimate the effect of vertical fractures on the areas swept after breakthrough in water flooding and miscible displacement programs such as gas cycling where the mobility is near one, The data are presented for the case of the fire-spot pattern in which the cemer well is fractured various lengths and orientations, the data indicate that for 10-acre spacing, fractures extetidirrg over 1300 ft in either directior1 from the fractured well may re.srrlt in reductions in sweep efficiencics from 72 to approximately 34 per cent. However. the area swept after break through may be quite largr and only 10 or 12 per cent 1ess than would be obtained if the reservoir were trot fractured. For the specific case when the volume of fluid injected is equivalent to 100 per cent of the pattern vol-unie, the swent area may vary from 80 to 88 per cent, depending on the lenght of the fracture. The former value is that which occurs when the break through or sweep efficiency was orrly 34 per cent and the latter figrrre of 88 per cent is that which is obtained if the reservoir were unfrac-ttm'd. It is pointed out that although the sweep efficiency may he very low in vertically fractured five-spot patterrz.s, the area swept at low water-oil ratios may be only 5 to 10 per cent less than those achieved if the reservoir were unfractured. INTRODUCTION Since the initiation of commercial reservoir fracturing techniques it has been desirable to determine the effect of fractures on the areas swept after breakthrough. Most water flooding or gas cycling projects are continued for substantial periods after the brcakthrough of the injected fluid. Although the sweep efficiency serves as one criterion for rating various flooding patterns. the area swept after breakthrough for various water-oil ratios or percentage wet gas, if cycling. is of perhaps more importance than the sweep efficiency alone. Sweep efficiency data on the vertically fractured five-spot have been presented3. Previous work on the line-drive pattern has shown the effect of vertical fractures on the area swept after breakthrough for the case in which the distance between injection and producing wells divided by the distance between adjacent input wells was equivalent to 1.5 (see lief. 2). The data indicated that for the line-drive pattern it may be desirable to flood or cycle substantially perpendicular to the fractures in order to achieve the greatest recovery for the smallest volume of fluid injected. For this study the center well of a five-spot is assumed as the fractured well. All fractures were assumed to originate at this well and extend into the reservoir for various distances and orientations. All the fractures are straight and are of large permeability compared to the matrix proper. These data are presented to aid the engineer in estimating fractured five-spot pattern performance. ANALOGY The potentiometric model was used in making this study. The model used was 20 20 in. by approximately 1-in. deep. For certain portions of the study one corner of this model was considered to be an injection well and the opposite corner a production well. To simulate vertical fractures a copper sheet was soldered to the wire well and made to conform to the desired length and orientation. In other studies the same model was used except that the four corners of the model might be considered as the corner wells of a five-spot pattern and a fifth well was placed in the center of the model. The well placed in the center of the model was fractured. The total fracture length is L and the well spacing. d. The complimentary fracture angles will be obvious from Figs. 3 and 4. The data obtained on the potentio-metric model assumes the pay to be uniform and homogeneous, the mobility ratio is one, steady-state conditions exist and gravity effects arc neglected. The permeability of the fractures is very great compared to that of the matrix proper. The po-tentiometric model has been used widely both in water flooding and gas cycling projects, and may be used for miscible displacement; how-ever. it is believed that the poten-tiometric model data are more properly applicable to gas cycling than water flooding because the model as-