Search Documents

By H. C. Kenny

THE annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200° to 350° C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet-though several investigators, beginning with Caesar and Gerner1 in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper-data are lacking on the problem: What is the specific influence of different amounts of silver on this tem-perature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it-is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also signifi-cant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered.

Jan 1, 1934

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By R. Stratton-Crawley

Flotation-related processes utilizing an oil phase for processing fine mineral particles have been described and various applications discussed. The problems associated with the techniques are varied, but may be summarized by the following areas; (1) applicability to fine particle beneficiation, e.g. collector extender and emulsion flotation. (2) major 'mechanical' problems, e.g. emulsion breakage and oil recovery in oil flotation. (3) complex interfacial chemistry, e.g. empirical nature of pigment flushing .

Jan 1, 1979

By E. J. Dulis, R. M. Fisher, K. G. Carroll

IT is well known that ferritic steels containing more than 15 pct Cr when subjected to temperatures in the range of 700" to 1000°F exhibit increasing hardness and decreasing ductility. The phenomenon has been widely termed the "885 °F embrittlement," after the temperature of most marked effect.'.' In view of the excellent review articles available in the literature3-6 only a brief account of experimentally established facts need be given here. The extent of changes in physical characteristics during embrittlement depends on chromium concentration and time at temperature, higher alloy content and longer time both promoting more rapid and extensive changes. In a 27 pct Cr steel, changes in impact strength and in angle of fracture in bending can be detected after only a 1 hr exposure at 885°F; after 50 hr this steel becomes quite brittle. Hardness increases slowly with time during thousands of hours exposure and may attain a maximum hardness number twice as large as that of the unexposed steel. Microstructural changes accompanying embrittlement have been described as an initial widening of grain boundaries followed by eventual darkening of ferrite grains. Embrittled steels etch more readily, e.g., the weight loss of a 27 pct Cr steel in acid solution may occur at a rate one hundred fold greater following exposure at 885 OF. Marked changes which accompany embrittlement have been observed in electrical resistivity, specific gravity, and magnetic coercive force. Changes in physical properties may be readily removed by heating at temperatures above the embrittling range, such as a treatment at 1100°F for 1 hr. It has frequently been noted that the 885 °F embrittlement suggests precipitation on a submicro-scopic scale of a chromium-rich constituent, the nature of which has not been revealed by X-ray diffraction. Progressive broadening of the body-centered cubic diffraction lines during embrittlement has been observed," and recent observations by Lena and Hawkes' upon single crystals have shown early asterism in X-ray photographs, disappearing within an hour at 900 °F. Many workers have ascribed8-13 the phenomenon to a precipitation of a phase (FeCr), which is known to cause embrittling effects at temperatures much higher than 885°F. Two general observations, however. suggest that a precipitation cannot be responsible for the 885°F phenomenon: 1—prior cold work greatly enhances a formation, whereas it scarcely affects the 885 °F embrittlement, and 2—the presence of an alloying element such as nickel or manganese may have an effect on the 885 °F embrittlement which is opposed to its effect upon a formation. The slight enhancement of a formation and 885°F embrittlement observed in the presence of elements with strong carbide and nitride forming tendencies' is probably a consequence of lessened chromium depletion of the matrix. The bar graph in Fig. 1 shows a typical example, taken from two 27 pct Cr steels used in this work, of the hardness after exposure for 10,000 hr at 900°, 1050°, and 1200°F. Steel A (0.03 pct C, 3.13 pct Mn) showed marked hardening at 900" and 1200°F, whereas steel B (0.12 pct C, 0.63 pct Mn) exhibited only the 900°F hardening. The cr phase was found in steel A at the higher temperatures but not in steel B. Presumably a formation is enhanced by the low-carbon and high-manganese concentrations in A," Thus there are two distinctly different hardening phenomena present which cannot both be ascribed to v precipitation without invoking a transition phase possessing remarkable properties. Materials A number of chromium steels exposed for long periods (5000 to 34,000 hr) at 900°F, as well as unexposed samples of one of the steels, were available for this investigation. Table I gives the chemical compositions and aging treatments of these steels. In addition to these steels exposed in the elevated temperature test furnaces of the National Tube Division, a number of high-chromium steels were heated for short periods in small laboratory air furnaces and lead baths. Supplementing these commercial steels, a sample of high-purity (0.018 pct C, 0.002 pct N) 28 pct Cr iron, exposed 1000 hr at 887°F. was furnished by the Union Carbide and Carbon Corp. In addition, an alloy of iron and chromium of high purity containing 46 pct Cr was used. This

Jan 1, 1954

By Zay Jeffries

IMAGINE a spinning sphere of hot matter about 8000 miles in diameter, rushing through space at a velocity measured in miles per second, and you have a rough idea of what our earth is supposed to have been like about two to four billion years ago. By applying all of the science known to man and, more especially, by determining the velocity of earthquake waves at different depths, making comparisons with meteorites, studying densities, compressibility of rocks and the nature of surface rocks, a fairly definite conception of the general constitution of the earth has been obtained.1 The earth is supposed to have a central core rich in iron containing a substantial amount of nickel and small percentages of several other elements. The density of the core is assumed to be about ten times that of water and the diameter about 4200 miles. An intermediate shell of density about 4, and thickness of about 1800 miles, is sup- posed to consist of heavy rocks including sulfides, oxides, and silicates. The outer rock shell, probably about 100 miles thick and with a density around 2.8, is thought to be composed mostly of silicates, becoming in general more siliceous as the earth's surface is approached. NATURE'S SMELTING OPERATION Nature seems to have subjected the earth to a stupendous smelting operation, burying beyond reach much of the metal that man recovers in his smelting practices. We live on the surface of Nature's "slag dump" and must be content, for the near term, to recover for man's

Jan 1, 1953

By R. S. Newlin

IN reality, the Butte district is the birthplace of the Anaconda Copper Mining Co., for it was here that strength was gathered and means provided for later expansions of the Company. The Butte district was organized at a miners' meeting on Aug. 20, 1866, primarily for gold placer-mining operations. Substantial amounts of placer gold were recovered from gulch gravels during the period 1862 to 1868. The earliest lode claim locations in the district were recorded in July and August 1864. Copper ore was first shipped, to Swansea, Wales, in 1866. In November 1866, according to the Montana Post, construction of a smelter was started to treat the silver

Jan 1, 1948

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950

By J. Randel Hill

The 64th Texas Legislature passed the "Texas Surface Mining and Reclamation Act," Chapter 131, Texas Natural Resources Code (subsequently referred to as "the Act"), at a point in time when little surface mining had taken place within the state. Thus, enactment of regulatory control governing mining operations in our state has, for the most part, preceded widespread, intensive mining activity. I should point out that the statute applies only to the extraction of coal, lignite, uranium and uranium ore. A recent opinion rendered by the Attorney General's office has stated that extraction of the named elements, when it occurs incidental to the extraction of other materials, e.g., clay, is not not an activity subject to the Act. An important theme of the Act, frequently overlooked in other environmentally oriented legislation, is recognition of the Act's affect on the mining industry. The Act states that "the extraction of minerals by surface mining operations is a basic and essential activity making an important contribution to the economic well-being of the state and nation" and, in reference to reclamation being accomplished contemporaneously with mining, provides a recognition that "the extraction of minerals by responsible mining operations is an essential and beneficial economic activity." This legislative recognition is, of course balanced against the need for proper mined land reclamation, the rights of surface owners, the need to guard against unreasonable degradation to land and water resources and numerous other actions or events that the Legislature wanted protected. Another rather pervasive general theme that is established in the Act is the concept that the agency is entitled to obtain whatever information, or take whatever action, that appears reasonably necessary to effectuate the purposes of the Act. This concept, coupled with the detailed requirements placed on mining operations in the portions of the Act dealing with Permit Applications, Reclamation Plan and Reclamation Standards, easily insures that surface mining activities can and will be regulated to the extent necessary. Section 131.102(b)(2) is probably the most relevant provision in the Act which deals with the preclusion of mined lands becoming waste lands. This portion of the Act states that the surface mining operator shall: ". . . restore the land affected to the same or a substantially beneficial condition. ." In this language the Legislature had made it abundantly clear that the abandoned or orphaned lands found in some of the Eastern states, will not be tolerated in this State, and provided the Commission with a degree of latitude to determine what condition would be appropriate in each individual mining situation. I bring this area of the Act to your attention because it is the area which has received the most inquiries and concern by operators, i.e. what does "substantially beneficial" constitute? The Commission's staff has spent a considerable amount of time wrestling with the statutory language "substantially beneficial" to determine the legislative intent and provide operators with guidance of what they can expect. In this regard, the most definitive criteria in our opinion lies in the Act's legislative hsitory. The Legislature had before it basically three reclamation standards namely: House Bill 656, considered to provide the most stringent reclamation standard and identical to Senate Bill 66; House Bill 1717 which was supported by industry spokesmen and was considered to contain the least stringent reclamation standard; and Senate Bill 55 which was adopted by the Legislature. During the Bill's initial hearing before the House Environmental Affairs Committee, the House sponsor of the Senate Bill 55, which was the Bill eventually adopted, made the following statement: (I am quoting verbatim from the Committee's transcript although substituting the speaker's reference to the authors names with the Bill's numbers.) "An example of the differing approaches of the four bills can be seen in the area of reclamation standards and this is critical. House Bill 656, talking about restoring the surface of the land, House Bill 656 has this statement: 'At least fully capable of supporting the use to which it was capable of supporting prior to any mining or any higher or better use.' In other words you have to restore it to the level it was prior to the mining. Senate Bill 55: 'Restore the land to the same or substantially beneficial use.' Substantially beneficial use. (Emphasis his) House Bill 1717 says: 'Restore insofar as practical to appropriate beneficial post-mining use.' So that House Bill 1717 said to, 'restore insofar as practical to appropriate beneficial use. I think that's too weak, whereas I think the House Bill 656 that would call you to restore it to at least the use it had prior to the mining may also be too tight the other way. I think the Senate Bill 55 approach is down the middle of the road which says that you do restore it to the 'same or substantially beneficial use,' is a proper way to go there." Therefore, the conclusion that we have drawn from the legislative history of the bill is that the extent of reclamation required by "substantially beneficial" may be something other than the use it was prior to

Jan 1, 1979

By Hugh H. Waesche

Of all the military services, the Signal Corps is the most concerned with piezoelectric minerals because of its function as a supply service to the strategic and tactical military forces. Consequently this paper is written from the point of view of one associated with that organization. The Signal Corps is responsible for the research, development, and supply of communications, radar, and components to the using services of the Department of the Army and to some extent the Other branches of the National Defense Department. Their work therefore includes the study of the sources* characteristics, and application of quartz and other piezoelectric materials. These materials have become a vital consideration in strategic planning and are essential for efficient tactical operation by all the Armed Forces. The Signal Corps at the beginning of world War 11 Was respon-sible for both Army Ground and Air Force electronic equipment. Since that time this Army service organization has probably done more in the development of frequency control devices using piezoelectric materials than any other group. The U.S. Department of the Interior, Bureau of Mines, Minerals yearbook of 1945, shows that during the four war years, 1942 through 1945, 9,598,-410 Ib of quartz crystal were imported for all uses and of this total, 5,168,000 lb were consumed to produce 78,320,-000 crystal units for electronic application. Other government records confirm these data which conclusively show that approximately 53 pct of the crystalline quartz imported was consumed in the production of electronically applied quartz crystal units. It may be assumed that some effort was made to maintain a stockpile over demands for all purposes. and this would mean that the actual percentage of quartz used electronically was considerably over the 53 pct figure. These data only emphasize that electronic application of crystalline quartz was the greatest requirement, and per- haps the actual value in this application to national defense is many times greater in importance than is apparent on first inspection. Current electronic research and development programs of the Armed Forces are planned around the fundamental use of piezoelectric minerals for frequency control and this at present, at least, means quartz. Definition and Early Development The word piezoelectricity is formed from combination of the Greek word "piezein". meaning "to press," and "electricity." It is that property shown by numerous crystalline substances whereby electrical charges of equal and opposite value are produced on certain surfaces when the crystal is subjected to mechanical stress. It appears to be intimately associated with the better known property, pyro-electricity and in fact, the two may be manifestations of the same phenomeuon. This property was discovered by Pierre and Jacques Curie in quartz, tourmaline, and other minerals in 1880 while studying the symmetry of crystals. The converse effect, that is, mechanical strain in the crystal when placed in an electrical field, was predicted by the French physicist, G. Lippman, in 1881, and verified by the Curies almost immediately. As has been the case with many discoveries of similar character in the basic sciences, not much attention was paid to this property for man)- years except as an entertaining curiosity. Between 1890 and 1892 a series of papers was published by W. voigt in which the theoretical physical properties were put into mathematical form. The first practical application of piezoelectricity occurred during World War I when professor P. Langevin of France used quartz mosaics to produce underwater sound waves. The same mosaics were used to pick up the sound reflections from submerged objects which were in turn, amplified by electronic means and used to determine the distances to such objects. This device was intended for use as a submarine detector but development was not completed in time for war service although it was used later for determining ocean depths. About the same time, A. M. Nicholson, of Bell Telephone Laboratories, developed microphones and phonograph pickups using Rochelle salt crystals. A major step in the application of piezoelectric quartz came in 1921, when professor W. G. Cady, of wesleyan university, showed that a radio oscillator could be controlled by a quartz crystal; from that date, this use of quartz has increased steadily, reaching its peak in world war 11 as is shown by the figures previously given. Essentially all American electronic equipment for communication, navigation, and radar, utilized quartz crystals for the exacting frequency control required. Crystalline Minerals with piezoelectric Properties QUARTZ Hundreds of piezoelectric crystalline materials are known, most of which are water soluble. Of these, quartz appears to be without a peer for electronic frequency control. Unfortunately, the quartz must be of superior quality. It must be free of mechanical flaws, essen-tially optically clear, free of both Brazil and Dauphiné twinning and must be, for average uses, over 100 g in weight. Because of these stringent requirements, raw quartz of the quality desired is of rare occurrence. In addition to quartz, several other naturally occurring crystalline materials are known to have the piezoelectric property and could perhaps be substituted for quartz in some applications. These

Jan 1, 1950

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By R. M. Goldhoff, J. W. Spretnak

IN connection with establishing the mechanism by which boron enhances the hardenability of heat treatable steels, this research work has been undertaken. Spretnak and Speiser1,2 indicated the need for studying high temperature effects in boron steels and, chief among these, the possible nonhomogeneous distribution of boron in iron grains. The occurrence of this effect may be of significance in explaining the mechanism of enhancement of hardenability by boron as well as in explaining some of the observed characteristics of boron steel behavior. Primarily, then, this work was undertaken a) to establish whether or not boron is adsorbed in ? solid solutions, b) to determine the nature of any such adsorption effects, i.e., whether it is positive or negative as well as its temperature coefficient, and c) to establish the magnitude of any such effect. While past literature on this specific subject is rather sparse, a number of authors have postulated that the observed temporary loss of hardenability as well as the occurrence of the characteristic boron constituent in these steels is due to the nonuniform distribution of boron in austenite.3-0 Experimental Techniques Attempts to obtain direct evidence of grain boundary effects in boron steels have been unsuccessful, both by using the technique of Chalmers' in which small concentrations of solute made radioactive by irradiation are detected by autoradiographic means, and by means of studying cleavage fractures with the electron microscope.8 The present study attempts the design of experiments to measure the effect of boron on properties which might be subject to variation because of grain boundary effects. A study of the theoretical aspects of grain growth indicates that such studies may be pertinent. Another valid type of experiment involves the measurement in polycrystalline materials of properties whose values depend on the bulk of the grain, being negligibly influenced by grain boundaries. One such property is the lattice parameter measured by X-ray diffraction. The value of the lattice parameter reflects the average conditions which obtain over a relatively large number of atoms in a fixed crystalline lattice, and is therefore mainly dependent on bulk grain material. Measurement of lattice parameter variation over the austenite range of temperature in iron with and without boron should give evidence of concentration variations in the bulk grain material if adsorption effects are significant. Finally, use is made of the Grange and Garvey3 metallographic test for boron in which a characteristic boron constituent can be developed in austenite grain boundaries. The very occurrence of this phenomenon suggests grain boundary enrichment of boron and a study of the occurrence of this constituent and its varation with austenitizing temperature should help to detect grain boundary effects. Materials One lb ingots of pure iron, an Fe-B alloy, an Fe-C alloy, and an Fe-C-B alloy were prepared. The melting technique included an initial melting of electrolytic iron under vacuum followed by remelting under hydrogen and, finally, by melting under argon with the addition of alloying elements. Each ingot was surface machined between meltings. A quantitative spectrographic analysis was obtained on the pure ingot and, in addition, oxygen, nitrogen, and carbon were determined by the vacuum fusion method. The results of these analyses are given in Table I. Semiquantitative spectrographic analyses were performed on the alloy ingots, while quantitative determinations of the alloy additions were obtained. These analyses are shown in Table 11. The cast ingots were subjected to the following sequence of fabrication treatments: forging to 5/8 in. bars, swaging to 0.300 in. rounds, drawing to 0.025 and 0.010 in. wire. Portions of each ingot were retained in the swaged condition for experimental use. For certain portions of the work typical commercial steels were used. These materials were supplied by the Republic Steel Corp., Canton, Ohio, and correspond to AISI 8640 and AISI 86B40 compositions.

Jan 1, 1958

Before hostilities between the colonies and Great Britain began in 1775, most of the coal used in the northern colonies undoubtedly came from England, with some supplies for New England coming from Nova Scotia; in New York and Philadelphia the supply came from England with some from the Virginia mines. Table 4 shows data obtained from the Public Records Office, London, for the years 1768-1772. This table supplements Table 3, which records only a few shipments from Richmond in 1768 and 1769; as there was no coal shown in imports coastwise in 1769 in Table 4, and only two small shipments in 1769 in Table 3, there may have been a cessation of shipments then, for some reason not now known. In Table 5 are incorporated all the data in the first two, with a few earlier years, and an attempt is made to estimate the amount used during the period by allowing for coal exported. With the small total tonnages a carryover from one year to another makes a large difference in the annual figures, but over the period the result may be fairly indicative of the amount of coal used before the Revolution. According to present day ideas the quantity of coal used during that war was very small, but apparently it was badly needed for the manufacture of the small amount of munitions made in those troublous days. As Philadelphia was the leading city along the Atlantic coast, and as the southeastern part of Pennsylvania was the leader in making iron, as well as making rifles, it is natural that the first call for coal came from there. At first, procuring supplies such as coal, powder and sulphur was handled by a Committee of Safety, which later became a Council of Safety and later this committee's functions were turned over to a Board of War, functioning with the military organization of the colony. . The organizations of the several colonies were slightly different, but Pennsylvania, Maryland and Virginia followed this scheme generally. Later in the war the Congress began to make arms for the troops, and it is difficult now, with the few records available, to tell when the state functions ceased and those of Congress began. On December 5th, 1775, the Committee of Safety

Jan 1, 1942

By James Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manu-facturing puzzolan cement; three companies, Birmingham Slag Co., Woodstock Slag Co., and Swann Chemical Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive.

Jan 1, 1937

By Jackson R. Pellett

INTRODUCTION The Friedensville mine is situated in Upper Saucon Township, Le- high County, Pennsylvania, in the southern central part of the Allentown quadrangle of the United States Geological Survey, approximately 5 miles southeast of the City of Allentown and 4 miles south of the City of Bethlehem. Zinc was first discovered in the Friedensville area early in the 19th century and several mines were operating during the latter part of the century. Zinc oxide was produced in 1853 and zinc metal in 1859. All mining in the area ceased in 1893 chiefly because of an unfavorable economic situation caused by a severe ground water problem and competition from the higher grade ores in New Jersey. Property acquisition by the New Jersey Zinc Company began in 1899 and periodic exploratory drilling was carried on until 1940 when sufficient reserves were proved for development of a mine. Shaft sinking was undertaken in 1947 and, due to severe hydrologic conditions, was not completed until 1952. Production began in 1958 and today the mine is producing about 64,000 tons of zinc concentrate per annum. The concentrates are trucked to the Company's smelter at Palmerton, Pennsylvania, approximately 30 miles north of Friedensville. The mine also produces from its mill tailings industrial and agricultural grades of limestone for commercial markets.

Jan 1, 1970

By Rees D. Rawlings, C. W. A. Newey

The aging characteristics of an Fe-11 at. pct Mo alloy have been studied by means of light metallography together with density, Young&apos;s modulus, and hardness measurements. The results were consistent with the precipitation of a single intermetallic compound during aging; overaging was slow relative to that in other iron-based binary alloys. The solution treatment temperature had a small effect on the rate of hardening whereas deformation prior to aging had a marked effect on both the rate of hardening and the peak hardness. The density data indicate that the compound precipitated is Fe3MO2 and not the Laves phase Fe2Mo. Analysis of the modulus and density results gave values for the time exponent for precipitate growth of approximately 1.0 and 1.5 for the alloy aged with and without prior deformation, respectively. DETAILED studies of precipitation hardening in bcc matrices have been confined largely to the effects of carbides and nitrides. In view of this and the growing technological interest in intermetallic compound strengthening, e.g., in maraging steels, a study of precipitation in iron-based alloys with a low interstitial content has been undertaken. This paper is concerned with the aging behavior of an Fe-11 at. pct Mo alloy; the mechanical behavior of the alloy will be reported later. The early work of sykes on Fe-Mo alloys showed that precipitation of the intermetallic compound was accompanied by an increase in hardness and a decrease in volume of the material. More recent surveys of the strengthening associated with precipitation have been made3-5 and, in particular, Elsen and wassermann4 showed that deformation prior to aging increased the rate of hardening. These latter workers also followed the precipitation process by means of dilatometry, electrical resistivity, and lattice parameter measurements. Their results confirmed that there is a decrease in volume on aging. Except for the work of Hornbogen on an Fe-20 at. pct Mo alloy, neither clustering nor the precipitation of a nonequilibrium phase has been observed in Fe-Mo alloys. Studies of alloys of lower molybdenum content475 indicate that the equilibrium intermetallic compound is precipitated during aging. However, there is some doubt concerning the nature of the equilibrium precipitate phase. According to the phase diagram constructed by Hansen,8 the phase should be precipitated. This phase has a rhombohedra1 crystal structure which is characterized by the formula Fe706,&apos; although the composition of the molybdenum-rich boundary corresponds approximately to Fe3Mo2. The version of the diagram proposed by Sinha, Buckley, and Hume-Rother indicates that the A phase, a Laves phase Fe2Mo, should be precipitated. Their observation of a Laves phase supports the earlier findings of Bechtoldt and Vacher,13 although, in a recent study of the system by means of diffusion couples, Rawlings and Newey did not detect the phase. The work presented here describes the effect of solution-treatment temperature, aging temperature, and prior deformation on the aging characteristics of the alloy as revealed by light metallography together with hardness, density, and Young&apos;s modulus measurements. In addition the density data are used in an attempt to determine the compound precipitated during aging. EXPERIMENTAL PROCEDURE A 29-kg ingot of the alloy was cast at R.A.R.D.E., Fort Halstead, from deoxidized, Japanese electrolytic iron and sintered molybdenum. The ingot was homogenized for 6 hr at 1473°K and then worked, with intermediate anneals, into 6- and 16-mm-diam rods and 6-mm plate. Chemical analysis of the alloy gave, wt pct: Mo, 17.5 (11 at. pct); C, 0.003; Si, 0.002; S, 0.005; P, <0.002; and02, 0.0098. Solution treatments were carried out under a dynamic argon atmosphere in a vertical, "crusilite" element, furnace which had a facility for rapid quenching into iced water. Except for the study of the effect of solution treatment temperature, all specimens were solution-treated at 1573" * 2°K for 1 hr. Salt baths were used for the aging treatments. Specimens for hardness, density, and Young&apos;s modulus measurements were produced, after heat treatment, from the stock rod or bar using a precision silicon carbide slitting wheel. As described later, the quenching treatment produced local plastic strain in the stock material; consequently, care was taken to ensure that the specimens were not prepared from these regions. Those specimens used in the studies of the effects of prior deformation on the aging behavior were strained in compression in a Denison universal testing machine. Specimens for light metallographic observations were mechanically polished on successively finer grades of diamond paste down to and then etched in either alcoholic ferric chloride or in a 2 pct nital solution. Vickers diamond pyramid hardness data were obtained using a 30-kg load. At least five impressions were averaged for each determination. Density measurements were made using a displacement technique in which each specimen was weighed in air and in dibromoethane at 296°K. The specimens were cylindrical and weighed 3 to 4 g; all weighings were made on a balance reading to 1 x 10"5 g. For each specimen the mean value of five weighings was used to calculate the density. The density of the dibromoethane was determined using the displacement procedure and a standard nickel specimen. The error in an absolute density value was estimated to be HI.01 pct. To obtain the density as a function of aging time a single specimen was used and the density meas-

Jan 1, 1969

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963