Search Documents

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By G. P. Connell, R. E. Gilmore, J. H. H. Nicolls

The purpose of this paper is to suggest a procedure for indicating the dividing line between noncaking coals and those that have weakly caking properties. A laboratory agglomerating test as an aid in classifying weakly caking coals is outlined and its merits in comparison with the standard agglutinating method advanced by the U. S. Bureau of Mines are discussed. No attempt, however, is made to discuss in detail either the different methods for determining "caking" and "agglutinating" indices or the various systems of classification. Two methods, differing somewhat in procedure, have been employed and recognized as suitable for determining the caking or agglutinating values of coals; namely, those in which an inert material such as sand, electrode carbon, etc., has been mixed with the coal before being heated, and those in which the coal is carbonized alone. In all such methods, the coal with or without the inert material is in the finely divided state and the index or value sought is derived from the examination of the residue after heating in a closed crucible or other container. The procedure outlined by Selvig, Beattie and Clellandl is the most recent representative of the method using sand as inert material, while the agglomerating test described below is representative of the method in which the coal is carbonized alone. The standard volatile-matter determination affords a means for observing the coking properties of a coal, and this has been described by Rose2 as the simplest of all coking tests. According to him, "the resulting coke button will indicate whether the coal is noncoking, feebly coking or strongly coking," despite the fact that "almost every condition in this test is at variance with large-scale carbonizing practice." Lessing,3 the

Jan 1, 1934

By E. Miller, K. Komarek, W. Johnson

The activity of aluminum in solid Cr-A1 alloys has been measured by an isopiestic technique between Cr-A1890' and 1126" and 13 and 80 at. pct Al. The integral free energy of mixing has a minimum value of —5600 cal per g-atom at 59 at. pct Al. The maximum solid solubility of aluminum in chromium was determined to be 43 at. pct Al, and the composition limits of the compounds CrA14, Cr4A19, and Cr5Al, at 1000"~ were found to be 79 to 80, 66 to 70, and 59 to 63 at. pct Al, respectively. The thermodynamic properties of the Cr-A1 system have been investigated as part of a thermodynamic study of aluminum-transition metal systems.172 Little information is available on the equilibrium properties of the Cr-A1 system. The heats of formation of solid Cr-A1 alloys have been determined by Kubaschewski and Haymer at 600" and low-temperature specific heat data have also been obtained.~ More extensive work has been performed on the phase diagram, and a compilation has been provided by Hansen and Anderko,~ their phase diagram at elevated temperatures being essentially based on the work of Bradley and LU.~ The high-temperature portion of the phase diagram shows an intermediate phase CrA14 decomposing peritectically at 1018°C and existing at 82 at. pct A1 at 1000°C. They also identified the compounds with solubility limits of 72 to 75 at. pct A1 at 1000°C, and Cr5A1,, existing at 61 at. pct A1 at 1000°C. The maximum solid solubility of aluminum in chromium at 1000°C was found to be 46 at. pct Al. These elevated-temperature data were obtained by examination of quenched samples and were considered as less precise than the lower-temperature data. Koester, Wachtel, and Grube7 have revised the phase diagram as a result of their magnetic susceptibility and X-ray study. The results of this work differ appreciably from those of Bradley and Lu at temperatures above 800°C. The CrA1, compound is given as existing between 79 and 81 at. pct A1 at 1000°C, and they do not indicate the presence of a CrA13 phase reported by Bradley and Lu. They also report the compound Cr4Alg as having solubility limits of 66 to 70 at. pct A1 at 1000°C, while Bradley and Lu show this compound stable only up to 870°C. Koester et al. state that the high-temperature modification of the compound Cr5A18 is stable down to 1125"C, and not 980°C as stated by Bradley and Lu, and that the low-temperature modification of Cr5Al, has a range of homogeneity of 58 to 63 at. pct A1 at 1000°C. They also report that the maximum solid solubility of aluminum in chromium is 43 at. pct A1 at 1000°C. APPARATUS AND EXPERIMENTAL PROCEDURE An isopiestic method was employed which has been successfully applied to the determination of aluminum activities in solid ~e-All and Ni-Al alloys. Alloy specimens were held at different positions in a temperature gradient and were equilibrated with aluminum vapor from an aluminum reservoir kept at the temperature minimum of an impressed thermal gradient in a closed alumina system. Diffusion of aluminum into the specimens occurred until equilibrium was reached, at which the partial pressure of aluminum in each of the specimens was given by the vapor pressure of the pure aluminum reservoir. The activity of aluminum referred to liquid aluminum as the standard state in a given equilibrated sample at temperature T could therefore be expressed by: vapor pressure of pure aluminum at _ the temperature of the reservoir Vapor pressure of pure liquid aluminum, at specimen temperature T Since both the temperature of the aluminum reservoir and the specimen temperatures were determined experimentally, and the vapor pressure of pure aluminum is known as a function of temperature,' the activity of aluminum in a given aluminum alloy of known composition could be calculated. Initial runs were made with samples consisting of pure chromium chips placed in alumina crucibles. These runs exhibited large inconsistencies, indicating that equilibrium was not attained. High aluminum content Cr-A1 alloy powders were therefore substituted for the pure chromium specimens. The starting composition of the alloys was adjusted through experimentation until the concentration change necessary to attain equilibrium was small. In this manner, consistent results were obtained in reasonable times. SPECIMEN PREPARATION Alloy specimens were prepared from chromium of 99.997 pct minimum metallic purity: with 0.028 to 0.038 pct H, 0.0002 pct N, and 0.27 to 0.46 pct 0 (Aviquipo, Inc.). The aluminum had a purity of 99.99+ pct and the following impurities: 0.003 pct Cu; 0.002 pct S; 0.002 pct Fe; 0.001 pct Pb; 0.001 pct Ga (Aluminum Corp. of America). Alloy powders were prepared from weighed mixtures of chromium and aluminum by double-arc melt-

Jan 1, 1969

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By Thomas M. Drown

AT the meeting of the Institute in New York,, in February, 1880,* I described a process of determining sulphur in metallic sulphides, with especial reference to the determination of pyrites in coal. The process, as then described, is as follows : A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromine is used it must be neutralized by the addition of a :little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.c. of this solution and heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then * Transactions, American Institute of Mining Engineers, vol. viii, p. 569.

Jan 1, 1881

By Fred C. Bond

THEM is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determinations of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

What has happened to the basic coal industry during the past year? Has it been a better year for coal than 1961? What striking new developments have occurred in mining, preparation and utilization? Are there positive signs that production will go up? What has happened in the utility market, the metallurgical market and the export market? Is the controversial question of coal transportation nearer to a solution? What progress has research made for coal during the year? The answer to these and many other important questions are offered in the following review of the Coal Industry-1962.

Jan 2, 1963

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By R. W. Raymond

The important question of the metallurgical value of the coals of the Rocky Mountains and the Pacific Coast is to be settled, of course, by practical experiment. Meanwhile, as I have had occasion to point out, the proximate analyses of these coals throws little light upon it, and is, indeed, likely to mislead the metallurgist, if he compares it with the results of similar analyses upon bituminous and semi-bituminous coals. With the view of showing how large a proportion of the material usually classed as(" volatile matters " consists of combined water, or oxygen and hydrogen presumably in chemical combination, I have collected a number of ultimate analyses from various sources, in the following tables. The numbered analyses in the first table are as follows: No. 1. Monte Diabolo coal—Analyst, H. S. Munroe, Col. School of Mines. 2. Weber Canon, Utah, " " " 3. Echo Canon, " " " " 4. Carbon Stat'n, Wyoming, " " " 5. " " " " " 6. Coos Bay, Oregon, " " " 7. Alaska, " " " 8. " " " " 9. Canon City, Colorado, " Dr. T. M. Drown, Philadelphia. 10. Baker Co., Oregon, " " " 11. Blockcoal,SandCr'k,Ind., " Prof. E. T. Cox. This table affords some suggestive comparisons, to facilitate which a remark or two, explanatory of its construction, will be useful. In the ultimate analysis of coals, the proportions are frequently calculated (as, for instance, in the report for 1872 of Prof. Cox, State

By William L. Zeller

IN the past 75 years industrial engineering has been highly developed in many fields, but the coal mining industry has just begun to realize its potential for cutting costs. To receive the maximum benefit, a company should apply industrial engineering from the time a new installation is contemplated, but the principles can also be used to reduce and control the costs of an established operation. One company that had been mechanized for seven years reduced its total labor cost 57 pct by industrial engineering. Of this reduction, 20 pct was brought about by a preventive maintenance, rebuilding, and scheduled lubrication program that eliminated 80 pct of the delay caused by mechanical and electrical failures. Thirty percent of the cost reduction was attributed to rearranging the work force into crews of the most effective size, changing working methods, and training all mine supervision in the principles of the cost reduction program. The remaining 7 pct reduction was brought about by a wage incentive program for all the men in the mine. The productivity of this coal mining operation was increased from less than 8 tons per payroll man to 20 tons. This increased productivity was brought about while using the same equipment, men, and supervision.

Jan 12, 1957

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

Experimental work on the properties of high-purity alloys of the copper-man-ganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. Previous Work Heuslerl conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilib- rium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alpha-beta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350' to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur6 have also noted this precipitate. Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By Adrien Berton

FOR nearly a century, the Corocoro deposit has been renowned among geologists from the fact that it shares with the Lake Superior deposits of the United States the distinction of being the only important copper districts where native copper is worked commercially. The Corocoro district, named after the city of Corocoro, the capital of the Province of Pacajes (Department of La Paz, Bolivia) is situated towards the western edge of the Bolivian high plateau, at an altitude of a little over 13,000 ft. The most interesting part of the district is that immediately surrounding the city of Corocoro, at a distance, by railway, of 65 miles from La Paz and 210 miles to the Chilean port of Arica on the Pacific Coast. The climate of the region is that of the semi-desert, dry and relatively cold, with big differences of temperature between day and night. The rainy season begins in December and ends in March. The cupriferous lodes of Corocoro have not attracted as much interest as the silver mines of Potosi but they have been known for a long time. In the precolonial period the Indians were using the charquis, or natural native copper sheets, to make small brass objects, and the beautiful pale green brochantite of the outcrops as a source of green pigments. During the colonial period, the oxidized ores of the outcrops were worked for copper, which was used by the mint at Potosi for making currency. The native copper ores were neglected because the Spanish miners were at a loss how to concentrate and smelt them. About 1830, work by rudimentary processes, which were improved little by little, was begun on the native copper ores. The total production of native copper in the following hundred years amounted to 100,000 tons. This native copper, which was remarkably pure, was much appreciated on the European markets before the introduction of electrolytic copper. It was useful for making special ornamental brass or bronze and the granular concentrates of native copper, called barrilla, containing 80 to 85 per cent copper were suitable for making copper sulfate by direct oxidation and subsequent leaching with sulfuric acid.

Jan 1, 1936

By Albert J. Phillips

IT is a privilege and a pleasure to deliver this, the Twenty-sixth Annual Institute of Metals Division Lecture. Eleven years ago C. A. Edwards addressed this audience on the subject "Gases in Metals." In spite of this relatively recent presentation, I propose to, present to you some quantitative considerations of industrial significance on the separation of gases from molten metals because recent observations and measurements, presented in the literature, have made it possible to evaluate mathematically the gases or gas-forming elements and to develop an understanding of the mechanism of gas separation that should permit, in many cases, the control of this baffling phenomenon. DEFINITIONS Before becoming involved in the subject it seems desirable, for the sake of clarity, to state certain definitions and axioms: I. We are dealing only with gases that separate from the molten metal either during cooling or in the transition from liquid to solid. Gases injected by the liquid stream and trapped in the solidified metal, or those forced into the solidifying metal from the mold due to either thermal or cher4ical effects are not considered. Neither are we concerned with the separation of gases within the metal after solidification is complete for the data on this subject are at least complete enough to permit the practicing metallurgist to satisfactorily control the phenomenon. 2. Only where there is a decrease in solubility or a change in equilibrium of either a gaseous element or an element that reacts to form a gaseous compound, can there be a separation of a gaseous phase from the liquid or solidifying metal. 3. The amount of gas separating from the liquid during solidification can be computed directly from the amount of the element contained in the liquid when freezing commences less the amount of the element found in the solid either as a separate solid phase or in solid solution. 4. There can be no separation of gas bubbles unless the told pressure of the gases in the liquid meld exceeds atmospheric pressure plus the hydrostatic pressure of ' the liquid metal head. (In addition, pres- sure resulting from surface tension in- creases the total pressure requirement for initial gas separation. Probably the remarkable differences in appearance caused by different gases in the same host metal are influenced greatly by the rate of diffusion of the gas in the liquid metal balancing the decrease in pressure as the gas bubble size increases and the surface tension effect decreases. Thus hydrogen with its high diffusion rate in liquid copper separates in the form of relatively coarse cavities for a given rate of heat extraction.) 5. Gas separation can take place at less than atmospheric pressure in the voids created by the shrinkage from liquid to solid, but since the voids are not caused by the gas the presence of gas in the voids is of importance only where it

Jan 1, 1947

By J. Szekely, V. Stanek

Heat and gas flow interactions in nonisothermal packed beds were examined in the paper. A study was made of the response of the system to a step or pulse change in the inlet gas temperature, with a fixed value of the overall pressure drop across the bed. Under these conditions the heat flow and fluid flow transients are coupled because the convective heat transfer rate is alfected by the mass flow rate of the gas which, in turn, for a fixed pressure drop will depend on the temperature profile in the system. The Problem was stated in terms of differential equations, which were integrated numerically. The parameters used in the computation were so chosen to reflect the operation of the stack region of blast furnaces and sinterbeds. The computed results showed that the pressure drop-flou1 relationships and the rate of progress of the temperature fronts (waves) were strongly interrelated and were also markedly affected by variations in particle size and in void fraction. MANY metallurgical processes involve the contact of solid particles with a gas stream in a packed bed arrangement under nonisothermal conditions. Examples are shaft furnaces, regenerators, pebble heaters, and the sinter process. Although the heat and mass transfer aspects of packed bed processing have been extensively studied, the associated flow phenomena and in particular the effects of nonisothermality on the flow, have received little attention to date. :In fact, most of the previous workers considered the flow rate of the carrier gas time invariant and independent of the heat or mass transfer processSzekely and carr2 have shown that the pressure drop-flow relationships in nonisothermal packed beds may be strongly affected by the temperature profile within the system. These authors have devised a method for relating the pressure drop to flow for a given temperature profile. thus providing an extension of the Ergun equation to steady nonisothermal systems. Finally, in a recent paper willmot3 examined the response of regenerators to externally imposed changes in the gas flow rate. Both these investigations were somewhat specialized since, in general, neither the temperature distribution nor the gas flow rate may be regarded as truly independent variables, thus the heat transfer and the fluid flow problems have to be solved simultaneously. The work reported here is divided into two parts: in Part 1 the general formulation is given and a detailed discussion is presented of fixed bed systems. Part is devoted to systems in which a gas and particulate solids are contacted in a counter flow arrangement. FORMULATION Consider a nonisothermal fixed packed bed, extending from through which a gas is flowing. The problem is to develop a relationship between pressure drop and gas flow (with the gas flow being the dependent variable) and to evaluate the rate at which a change in the gas temperature, imposed at the inlet, travels through the system. Let us consider an infinitesimal section of the bed and establish differential heat, mass, and mechanical energy balances over this region. In addition, relationships are needed describing the temperature dependence of gas density (equation of state) and the temperature dependence of viscosity. These may be written as: where c, and are constants. It is noted that in this formulation we neglected any temperature gradients within the solid particles, thus assuming these to be either sufficiently small or of sufficiently high thermal conductivity to meet this condition. The justification and consequences of this assumption will be mentioned in the discussion.

Jan 1, 1970

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934