Search Documents

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By F. W. Jessen, R. W. Durie

The dissolution of salt in the development of salt cavities is controlled by free-convection boundary layer flow along the salt surfaces. It is the purpose of this paper to expand upon results published previously, and primarily to illustrate the influence of surface features on the boundary layer and hence the dissolution process in the development of underground salt cavities. General dissolution equations are presented that apply to a surface inclined to the vertical. A salt surface inclined so as to be overlain by water is dissolved by boundary layer flow, while an inverted surface is dissolved by a combination of boundary layer and cellular flow. Detailed investigation of the boundary layer was limited to laminar free-convection flow. Truly laminar free-convection boundary layer flow may be encountered only in laboratory solution cavities, but the boundary layer will control dissolution even where cavity dimensions are such that free-convection turbulence will occur. The factors found to significantly affect the laminar boundary layer will affect dissolution with a turbulent boundary layer. INTRODUCTION Underground salt cavities have been used extensively for the storage of LPG products, and the use of these cavities is expanding each year. The increasing requirements for such cavities suggest the need for a better understanding of the mechanisms involved, for the purpose of the control of cavity geometry and the most effective use of the injected water. A previous paper outlined a quantitative approach to the determination of salt dissolution rates in the laminar free-convection dissolution of salt. It is the purpose of this paper to expand upon the results previously published and to point out significant factors in the application of these results to the dissolution of field cavities. The dissolution of salt in laboratory scale cavities is controlled by the free-convection boundary layer, which is the region of flow along the salt surface caused by the difference in buoyancy forces resulting from the salt dissolution. The transfer of salt into solution at the salt face causes an increase in salinity, and hence a greater density, in the water at the salt surface. The region of higher density tends to fall through the lighter, less saline water and a flowing boundary layer is the result. The water remains stationary at the contact with the salt surface,l so the resulting velocity profile is such that the influence of gravity is opposed by a viscous shear force at the salt surface. For salt to be transferred into solution from a solid surface to a boundary layer of fluid, it must diffuse through a stationary film of water at the salt contact. According to Fick's first law, the rate of mass transfer by diffusion is the product of the diffusion coefficient and the concentration gradient, with diffusion transfer in the direction of decreasing salinity. Once the salt has passed into the boundary layer, it will be transferred by a combination of molecular diffusion and convection. The convection transfer will in turn affect the rate of dissolution by influencing the gradient of the salt concentration at the surface. In the previous investigation by the authors to determine the basic mechanism of the salt dissolution process, an equation was developed that agreed very well with the experimental rates of free-convection salt dissolution from a smooth vertical surface. The technique was taken from the work of Eckert2 in the analogous heat transfer system and will be referred to as the integral method. The rate of salt transfer from a vertical section of height H was found to be:

Jan 1, 1965

By G. R. Leverant, C. P. Sullivan

To evaluate the effect of a dispersion of nondeform-able, incoherent, second-phase particles on high-strain cyclic deformation and fracture, recrystallized TD-nickel (Ni-2ThO2) and a commercially pure nickel, Ni-200, were fatigued under strain control at total strain ranges varying from 0.009 to 0.036. Relative to the Ni-200, the slip at the surface of the TD-nickel was more wavy and discontinuous due to the presence of the thoria particles. This made crevice formation (incipient cracking) within slip bands more difficult in TD-nickel than in Ni-200. Both materials cyclically hardened to a constant (saturation) flow stress which increased with increasing plastic strain amplitude. Cellular substructures were developed in both materials during cycling. The cell size in TD-nickel was controlled by the thoria particle distribution and was independent of plastic strain amplitude over the range investigated. The cell size in Ni-ZOO was larger than that in TD-nickel at similar plastic strain amplitudes and was a function of plastic strain amplitude. These results, together with the cyclic stress-strain curves for both materials, are discussed in terms of a model for fatigue strain accommodation at saturation recently proposed by Feltner and Laird. NUMEROUS fatigue investigations have considered the interrelation of slip character, dislocation substructure, and cracking in pure metals and solid-solution alloys. However, except for the studies of the low-strain fatigue of internally oxidized copper alloys1 and cast, dispersion-strengthened lead,&apos; little is known about the effects which small, incoherent, nondeform-able, second-phase particles have on cyclic deformation and cracking processes. Effects due to the particles alone are often obscured by a dislocation substructure introduced during thermomechanical processing of dispersion-strengthened metals. In the present study, recrystallized TD-nickel and a commercially pure nickel, Ni-200, were employed to evaluate the effect of a thoria dispersion on high-strai fatigue deformation and cracking at room temperature. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in.-thick stress-relieved plate which had been subjected to a proprietary schedule of thermomechanical treatments, and the Ni-200 as 3/4-in. bar which was subsequently annealed for 2 hr at 850°C in argon resulting in an average grain diameter of 0.05 mm. The compositions of these materials are given in Table I. The microstructure of the TD-nickel consisted of elongated grains parallel to the primary working direction with an average width of 0.16 mm, Fig. l(a). Many fine annealing twins were present indicating that the starting material was in a recrystallized condition; this supposition was confirmed by the absence of of any extensive dislocation substructure, Fig. l(b). Sheetlike stringers parallel to the rolling direction were occasionally seen both within grains and at grain boundaries. Some approximately spherical particles about 2 in diam, which may correspond to exceptionally large thoria particle aggregates, were also present. The average Young&apos;s modulus of the plate material in the rolling direction was 21.8 X 106 psi which is consistent with a {100}<001>recrystalliza-tion texture3&apos;* being prominent. In transmission microscopy, the 2.3 vol pct of thoria particles generally appeared to be uniformly distributed although some clusters, 0.1 to 0.3 in diam, of larger particles were observed as previously reported for TD-nickel sheet,5 and stringering of particles was present in some areas as welt. The average diameter of the thoria particles was 450A with a calculated mean planar center-to-center spacing of 2100A, as determined by quantitative metallographic analysis.= The 0.2 pct offset yield stress was 36,000 psi which agrees with the value predicted by the modified Orowan relation7 for edge dislocations bowing between thoria particles of the size and spacing observed in the present investigation. Fig. 2 illustrates the specimen design employed for the axial high-strain fatigue testing. Adapters were screwed onto the threaded portions of each specimen so that testing could be performed in the same manner as that reported for buttonhead specimens.8 Stressing was coincident with the working direction for both materials. The gage section of each specimen was electropolished and lightly etched prior to testing. The total strain was controlled, being varied between zero and a maximum tensile strain ranging from 0.009 to 0.036. In addition to these tests, a circum-ferentially notched TD-nickel specimen was cycled over a total strain range of 0.0075. The same strain

Jan 1, 1969

By A. F. Frederickson

Rapid advances in any branch of science often follow the development of new instruments or techniques which permit the scientist a closer look at the material in which he is interested. With the development of the polariz¬ing microscope, modern petrology was born. The resolving power of the microscope, however, was not great enough to enable the geologist to dis¬tinguish or identify the material now known to be minerals which constitute the bulk of the rocks known as "clays" and laterites. The discovery of X-rays and the development of powder X-ray diffrac¬tion techniques provided the extra resolving power necessary to get "a closer look" at the minerals in the clays and laterites. These techniques are largely responsible for the great strides made in the past two decades in the identification of the clay, sesquioxide and hydroxide minerals. To obtain an X-ray diffraction. pattern of a mineral or rock is relatively a simple procedure, but to interpret this pattern in terms of crystal structure or min¬eral identity is quite another matter. It has taken the combined talents of physicists, physical and colloid chemists, mineralogists, and geologists to unravel the identity of some of the minerals in these complex rocks and, as this symposium will indicate, many more problems remain to be solved. To assist in the identification of these minerals, we have the ever-useful microscope, which, is supplemented by the development, only in the last ten years, of differential thermal techniques and the powerful and costly "eye" that enables us to see the shapes and sizes of extremely small particles -the electron microscope. To this array of equipment must be added such gadgets as supercentrifuges, spectrographs, and the apparatus necessary for chemical analytical work. Obviously, not only is it difficult for any one man to master all of the techniques to the point where he can do competent re¬search, but also few institutions are able to provide the high capital outlay for purchase and maintenance of suitable equipment. Here we clearly see that if this equipment is to help us solve our many problems, a close co¬operation of specialists from various institutions and industry is essential. This, however, is less than half the problem. If the geologist is going to learn to intelligently find, and the industrialist to intelligently and eco¬nomically exploit the materials that constitute a large part of the mineral wealth upon which our way of life is based, we must get a better insight into

Jan 1, 1952

By R. G. Treuting, R. M. Brick

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By R. M. Brick, R. G. Treuting

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949

By D. C. Buffum, L. D. Jaffee

THAT the path of brittle fracture in temper brit-tle steel differs from the path in unembrittled steel has been known for some years1 More recently it has been recognized that alloy steels, at least, display two forms of temper brittleness1 which may be called upper-nose and lower-nose. No experimental evidence has been published, however, to show that the two forms can be distinguished by simple inspection of brittle fractures. Fig. 1 is a photograph of the fractured surface of a V-notch Charpy specimen of SAE 3140 steel in which temper brittleness developed during heat treatment in the lower-nose temperature range.&apos; The steel was austenitized 1 hr at 900°, tempered 1 hr at 675", and embrittled 48 hr at 500°C, with water-quenching after each treatment. The temperature of transition from ductile to brittle fracture in the Charpy test was + 2°C (criterion of transition: 100 pet fibrous). The hardness was Re 25; the austenite grain size ASTM 8. This specimen was broken at 150°C in the standard Charpy test and absorbed 6.6 ft-lb; its fracture was rated 0 pet fibrous. Fig. 1 shows that the fracture appeared rough to the naked eye. At the side of the specimen away from the notch (the side which was in compression during the test), the surface as a whole deviated sharply from a plane. At higher magnification, X60, the surface gave

Jan 1, 1959

By David A. Summers, Clark R. Barker, Marian Mazurkiewicz

In May 1975 the U.S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a longwall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting ahead. The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the coal cantilever over onto the conveyor [(Fig. 1)]. There were several potential advantages foreseen for the system; perhaps the most significant were the elimination of coal dust from the working area and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in haulage horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of Mines contract. The experiments showed that it was more advantageous to work at a pressure of 68.9 mPa (10,000 psi) with an estimated flow rate of 3.15 X 10 - 8 m3/s (50 gpm) than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1979

By J. S. Kirkaldy, G. R. Purdy

THE formation of ferrite in supersaturated aus-tenite has been the subject of considerable speculation and investigation. Aaronson has recently reviewed the data pertinent to this reaction.&apos; Since these data in all cases refer to ternary or high-order alloys it is not possible to put them to the test of simple binary diffusion formalism. It has not, therefore, been possible to make a certain statement as to the controlling mechanisms in the process. An assessment of the difficulties inherent in the conventional statistical metallographic approach suggested that a study of the problem by means of a macroscopic two-phase diffusion couple might contribute useful information. Accordingly, such a couple was synthesized, and the rate of motion of a ferrite-austenite phase boundary (the growth of an austenite layer at the expense of a ferrite layer) was determined. Wagner originally produced a diffusion solution applicable to the motion of a planar phase interface in a binary diffusion couple, assuming local equilibrium throughout the diffusion zone. This solution, which is stated free of typographical error* in Ref. where a is the position of the interface in A space (A = x/fi), C; and CL1 are the equilibrium inter-facial concentrations in phases I and 11, C: and C*1 are the initial bulk concentrations in phases I and 11, and & and are diffusion coefficients (assumed constant). If a diffusion couple consisting of homogeneous layers of ferrite and austenite in equilibrium is raised to a higher temperature, the austenite layer will grow at the expense of the ferrite. Provided that the thickness of the ferrite layer is much less than the diffusion length of carbon in ferrite, we can set , so that Wagner&apos;s solution reduces to

Jan 1, 1963

By Rollin A. Slater

This paper presents a composite of ideas on materials handling systems by describing the design of an over-all system for a hypothetical steel pellet plant located on the Great Lakes. The bulk materials handling industry has served for years as the skeleton and the central system of nerves and nourishment for the body of basic industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. Materials handling technology has likewise improved its techniques and currently has a new, stronger generation of equipment to perform its necessary supporting function. Drawing upon excerpts from several recent plant designs, this paper describes a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details are not available for publication, and therefore the plant described herein is a composite of ideas. This imaginary plant will be located on the United States side of the Great Lakes and its owner will be called the Hypothetical Steel Corp. for purposes of discussion. TYPES OF EQUIPMENT The basic bulk materials handling systems and components required in a plant so situated are: lake boat unloaders; railroad train unloading systems; storage pile stackers and reclaimers; large bins and regulating feeders; and the conveyor systems — with their attendant controls— which connect the foregoing. PROGRAM OF DEVELOPMENT The initial work on the plant must be that of the process engineers who develop and refine the basic data, i.e., the logistics of all raw materials, waste materials and products within the plant. During this phase of study, the materials handling engineer may advance his planning only in basic areas such as movements at the dock and movements at the railroad. This initial planning work is concerned only with defining logical plant locations in the light of channels, currents, existing traffic, governmental regulations, locations of existing railroads and available rights-of-way. These systems alone have their own individual criteria which must be respected and accommodated in the final layout. All other elements, such as the arrangement of the blast furnaces, power house, coke plant, by-product plant, scrap preparation plant, BOF shop, and facilities for continuous casting, degassing, calcining, etc., are dictated by their own specific needs and their relation to each other. In the arrangement of these latter facilities, the materials handling system is secondary and must be designed to accommodate. BASIC LOGISTICS The result of the process engineer&apos;s work can be expressed in terms similar to those shown in Table I. Plants are customarily rated in terms of annual tons of ingots. Therefore, the basic size of this plant can be determined by referring to the BOF Shop wherein it is sized at 5 million tpy. From the base, the required hot metal can be traced to the blast furnace, which in turn indicates the amount of required flux, iron bearing materials and coke —which in turn establishes the demand for coal. Likewise, the total demand for flux can be determined by the combined demand of the lime plant and blast furnace. The generation of fines and waste products, which have significant value but are not usable as such, create the need for a sintering plant. From projections such as the foregoing, the complete flow of materials can be established and accommodated. The basic premise upon which this typical materials balance is predicted is that the plant will be a producer of high tonnages of non-SpecialtV- products. All basic raw materials (flux bearing, iron bearing, coal) will be prime quality. For example, the basic iron charge will be pellets, and the iron ore fraction will be sized lump, all of which

Jan 1, 1970

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By Lyall Zickrick

NUMEROUS brands of virgin pig lead are used in the manufacture of lead and lead-alloy cable sheath for commercial cables. In changing from one brand of pig lead to another a readjustment of press operating conditions is nearly always necessary. This is due largely to different flow characteristics, and some brands extrude at a much lower pressure than others; for example, copper-bearing lead requires much more pressure than a low-bismuth lead under the same operating conditions. With the modern type of lead press the extrusion practice in general differs very little. Molten lead at a temperature of 375° to 400° C. (710° to 750° F.) is cast in a water-cooled cylinder and allowed to cool or solidify into a slug for six to nine minutes. . This slug is forced into the die block and around the core tube through which the cable runs. The die block is held at an optimum temperature by means of gas flames, usually 175° to 225° C. (350° to 4.35° F.). Measurements of the tem¬perature of the cable sheath taken at the time of extrusion have covered a range of 190° to 225° C. (375° to 435° F.). According to Tammann, the rate of extrusion for a metal under constant pressure through a simple orifice is almost doubled for each 10° C. rise in temperature. Because of the irregularity of die-block construction, such a great increase is not obtained in lead-cable extrusion practice. To obtain more" definite information about the effect of small per¬centages of metals usually present as impurities in virgin pig lead, a series of compression tests were made covering several different brands of lead and various alloys. Since the usual temperature of the sheath is approxi¬mately 200.° C. as it emerges from the die block, these compression tests were all performed at 200° C. Five different brands of virgin pig lead were selected, as follows: Brand A: A desilverized western lead of very high purity. This lead contains neither copper nor bismuth. Brand B: A bismuth-free southeastern Missouri lead, usually con¬taining 0.05 to 0.08 per cent copper. Brand C: A copper-free mid-western desilverized lead of very good grade, usually containing around 0.06 to 0.10 per cent bismuth.

Jan 1, 1932

By Ronald K. Linde

Metastable Ag-Cu solid solutions at two compositions beyond the maximum limits of solubility obtainable by quenching from the solid state were obtained by rapid quenching from the liquid state. The process of transformation of the metastable solid solutions into the equilibrium phases was studied by means of X-ray diffraction intensity measurements and electrical-resistance measurements; metallographic examination was also performed. Results are compared with those for an alloy quenched from the solid state at a composition which exists as a solid solution at elevated temperatures. Activation energies for the trans-formation were computed to be 33,600 * 2500 and 33,100 * 2000 cal per g mole for the 60.1 and 75.0 at. pct Ag;Cu compositions, respectively THE kinetics of precipitation in supersaturated solid solutions obtained by quenching from high temperature has been thoroughly studied in many alloys, and detailed investigations of the early stages of nucleation and subsequent growth of the equilibrium phases have been carried out. All of these studies have been made on alloys quenched from the solid state, however, and it is the purpose of this paper to present some of the results on the kinetics of transformation of metastable solid solutions in Ag-Cu binary alloys whose compositions lie outside of the solid-state limits of solubility. Limits of solubility in the solid state can be increased by rapid quenching from the liquid state. This was first demonstrated by Falkenhagen and Hofmann, who obtained appreciable increases in solubility limits of the elements of the first transition series in aluminum by rapid cooling of liquid alloys through contact with a copper mold maintained at liquid nitrogen temperature.&apos; The same basic idea of cooling a liquid alloy by conduction onto a substrate rather than by convection of a gas or liquid (conventional quenching) has been recently revived and extended to very high rates of cooling by Duwez and his collaborators. The new technique was first applied to Ag-Cu alloys because the existence of a eutectic in this system is not predicted by the Hume-Rothery rules of alloy phase formation. Rapid quenching from the liquid state resulted in metastable solid solutions at all concentrations. The kinetics of decomposition of these metastable solid solutions containing 60.1 at. pct Ag;Cu (eutectic composition) and 75.0 at. pct Ag;Cu is the subject of the present paper. EXPERIMENTAL TECHNIQUES Alloys were made in 10- to 20-g heats using silver of purity 99.99 pet and copper of purity >99.999 pct. Components were weighed accurately to 0.1 mg and melted by induction heating in an alumina crucible under an atmosphere of hydrogen. Weight losses amounted to less than 0.02 ~ct in all cases. Rapid cooling from the liquid state was achieved in an apparatus of the type described by Pietrokowsky. 3 In this technique a freely falling drop of molten alloy is caught between a stationary anvil and a fast moving piston, both anvil and piston being lined with copper. The resulting foils were approximately circular (about 2 cm in diam) and from about 50 to 150 u in thickness, depending on the pressure driving the piston. Metallographic samples were prepared for polishing by edge-mounting foils in Quickmount. The mostef-fective etching procedure was found to be: 10 parts NH4OH (concentrated), 1 part H2O2 (30 pct), 5 parts H2O, swab for 5 to 10 sec. The transformation of the metastable alloys to equilibrium was followed by X-ray diffraction and electrical-resistivity measurements. The peak intensity and the integrated intensity of suitable Bragg reflections of the metastable and stable solid solutions were studied with a Norelco dif-fractometer, using nickel-filtered copper KO radiation. The peaks were step-scanned at intervals of 0.05 deg. Using either a Kelvin bridge or a null circuit with a Leeds and Northrup K-2 potentiometer, the changes in electrical resistance due to phase transformation were measured for specimens cut into strips about 20 mm long and 4 mm wide. All resistivity measurements were carried out at liquid-nitrogen temperature. The isothermal heat treatment was accomplished by sealing the samples in argon-filled aluminum containers with stainless-steel O-rings. Containers were then suspended in wax baths with temperatures in the

Jan 1, 1967

Wartime geological studies by the U. S. Geological Survey and subsequent drilling carried on by the Bureau of Mines disclosed new ore in the Illinois-Wisconsin zinc field. As a result, several companies are carrying on drilling programs to locate and define new ore bodies. The Vinegar Hill company, which operates a custom mill to handle ores from various sources, now employs about fifty men in production at their Andrews mine. The ore is usually found in a 200-ft horizon below the surface. Water problems are not serious. Commercial-grade ore ranges up to 8 and 9 per-cent zinc and the cut off is approximately 41/2 percent.

Jan 1, 1948

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr&apos;s salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr&apos;s salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By D. T. Peters, C. R. Cupp

Aging of commercial 18 pct Ni maraging steel and of related binary, ternary, and quaternary alloys has been studied by electrical resistivity, X-ray diffrac-tion, and hardness measurements. The aging process is in three stages: 1) recovery of martensite; 2) two precipitation reactions; 3) formation of nickel- rich austenite. The main objective of this work was to discover the nature of the Co-Mu interaction. Addition of cobalt to the Fe-18 pct Ni-5pct Mo alloy results in acceleration of the pvecipitation reaction by increasing the super-sat~lration 0f molybdenum. The cobalt-containing al- loys show no incubation period for the precipitation reaction, but the alloy without cobalt shows an initial slow reaction. These results are interpreted in terms of precipitation on dislocations. At low aging temperatures, the presence of cobalt leads to the appearance of a second type of precipitate which is a particularly effective hardener. Cobalt was found to retard the formation of austenite. Overaging is a combination of classical overaging and the formation of austenite in the structure. he- activation energy for the precipitation reaction determined from resistivity ,measurements is 42.8 kcal per mole and the growth of the precipitate is found to obey at law at high tenzperatures and a tU3 law at low temperatures. HE mechanism of strengthening of the 18 pct Ni maraging steels has been studied extensively since 1962.&apos;-? The strengthening is due to precipitation hardening of the martensitic matrix. The main precipitate is an inter metallic compound involving molybdenum, but there is disagreement about its identity.

Jan 1, 1967

By Walter Lang

The year 1931 has shown a marked change over 1930 in New Mexico, with respect to the volume of activities attendant upon the petroleum industry. Although the total production of oil and gas this year exceeds that of preceding years, the results have been attained from established units operating under restriction, but capable of supplying far more than the economic conditions justify. The presidential order of March 12, 1929, that "there will be complete conservation of Government oil in this administration," has merely anticipated a normal consequence of overdevelopment. As a result of the combined economic and legal restrictions imposed, very little new drilling has occurred during the year. Even in proven areas the drilling of offsets has been curtailed to the absolute limit of requirements. Scouting and sample-cutting, which in 1930 were still in a state of feverish activity, are at low ebb, and lease buying has reached a condition of stagnation. A number of the major oil companies have either materially reduced their field and office forces or completely eliminated local office representation. Two tests of particular interest, because correlation shows them to be structurally high although they failed to produce, are the National Securities well drilled six miles west of the town of Hobbs, on sec. 33, T.18 S., R.37 E., Lea County, to a total depth of 4272 ft., which developed a flow of 4,000,000 cu. ft. of gas at 3860 ft., and a show of oil; and the Western Drilling Co. No. 1 State, sec. 16, T.20S., R.32 E., Lea County. The latter test found dead oil at 2575 to 2580 ft., and sulfur water at 2745 ft., increasing to 2780 ft., representing the zone from which production was generally expected. The well was drilled to 4013 feet. The discovery of sulfur at about 950 ft. in the deepening of an old water well (Pearson, NE. 1/4 sec. 8, T.16 S., R.25 E.) drilled in the Little Cottonwood area northwest of Artesia led the Union Sulphur Co. to drill three prospect tests on a block of acreage in the vicinity during the summer and fall. The results of the investigation have not been disclosed. The Kummbaca Oil and Gas Co. drilled the T. J. Kerline No. 1, in sec. 34, T.21 N., R.30 E., Harding County, gaging 3,654,000 cu. ft. of 98 per cent CO² at 940 ft. The Barton structure, 20 miles east of Albu-

Jan 1, 1932