Search Documents

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

Edward Dyer Peters, the only child of Henry Hunter Peters and Susan Barker Thaxter, was born in Dorchester, Mass., June 1, 1849. From his father he was a descendant of the Peters family of Ipswich and Andover, Mass., whose earliest ancestor settled in Essex County in 1659; while upon his mother's side he descended from several old Hingham families, as well as from the Quineys and from Governor Bradford. Between the ages of fourteen and sixteen he was a student at the Episcopal School for boys in Cheshire, Conn. Near the school was an old tin mine, and he used to spend his Saturday afternoons exploring it. When Edward was sixteen, his father sold his property in South-borough, and for the next three years lived in Europe. Sept. 26, 1865, Edward entered the Royal School of Mines at Freiberg, Saxony. In the summer of 1867 he joined his family on Lake Geneva, and spent a part of the season in that vicinity, going to Chamounix and taking other trips. Extract from a letter to his father: Elbingerode, Harz, Aug. 30, 1868: I left Freiberg with my friend Lilienthal, on Wednesday the 19th of August, reached Leipzig in the evening and spent the night in that city: the next morning we took the cars and in the afternoon reached Eisleben, in Prussia, which was to be our first stopping-place; there are immense copper-mines and smelting-works at this place, and the method of working the mines is very peculiar ... The next morning we got up at five and spent the whole day in the smelting-works where I obtained a number of drawings of the furnaces they use here and a good many valuable data. Saturday morning we got up at four o'clock, and descended a mine about three miles from the town; the Director of this mine was one of the most intelligent and agreeable men that I ever met; he accompanied us in the mine and explained everything that was new to us. The system of mining at Eisleben is peculiar to this town, and is not used at any other place in the world; the copper ore comes in narrow, flat veins eighteen inches high, at the utmost, consequently the men work lying flat on their left side and using the pick with both hands: the ore is carried out of the side passages into the main ones, in very low waggons about twelve inches high, and four by two feet; the boys who pull these waggons have a board buckled to their left thigh and their left arm; they pass their bare foot through a strap in the waggon and wriggle along on their side dragging the waggon after them, with their foot, almost as fast as a man can walk above ground. In the afternoon we walked over to Hittstadt, about twelve miles, and remained there Sunday and Monday. Monday night, at ten o'clock we went out to one of the smelting-works, to see the refining of the copper; this is only done at night, so we worked there from ten in the evening till eleven the next morning, and came home all blackened up and with blistered hands, for our skin was not quite so tough as that of the workmen: at noon the same day we took the stage to Ascherls-leben, and then the train to Stassfurt, where there are immense salt-mines, as well as factories for the manufacture of bromium, which latter process is, however, kept a profound secret, so we had very little hope of seeing anything but the salt mines; we were talking with our landlord about our disappointment, that evening, when he told us that the director of the Bromium works was sitting in the next room with no company but his glass of beer, so we went over to him, introduced ourselves as Americans, and actually succeeded in persuading him that it could do his business no earthly hurt if he showed us his works; at last he consented, after making us give our word of honor

Jan 1, 1919

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By C. R. Kuzell

The Editor desires to call attention to the charts in the paper of the above title which were published in the August Bulletin on pages 2190 and 2191. It was impracticable to include in the Bulletin. charts of sufficient size to be used as working diagrams for the direct determination of operating values, but the Institute is prepared to furnish copies of these charts on a large-size scale, at a moderate cost, to those who desire to have them for this purpose. CORRECTIONS Page 2185, line 3. For "is accessory apparatus" read "in accessory. apparatus." Page 2188. Substitute for lines 11 and 12: Nitrogen, oxygen, carbon monoxide, Cp = 6.50 + 0.0010T Hydrogen, Cp = 6.50 + 0.0009T

Jan 9, 1914

In the Philippines, where distances are spoken of in terms off fight time, the Sipalay copper mines are two flight hours southeast of Manila on the island of Negros. After landing at the airport in Bacolod, it is then 170 km (106 milers) by surface transportation to Marinduque Mining and Industrial Corp.'s expanding copper operation. While copper deposits were discovered in the area in 1936-and one mine, the Binulig, began operations soon after-it wasn't until 1956 that stripping at Sipalay and construction of a 4000-t/d (4400-stpd) mill began. The mill went into operation in May 1957, and the first shipment of copper concentrate was made three months later.

Jan 8, 1978

By S. F. Shaw

In 1913, the Tiro General mine, at Charcas, S.L.P., Mexico, which had been making from 125 to 150 gal. of water per min., was allowed to become flooded, after all the pumps had been removed, and in 1918 the problem of unwatering it came up for solution. There are two vertical shafts, the Tiro General, 1390 ft., and the San Fernando, 1225 ft. in depth, with five connecting levels between them. The San Fernando shaft had been partly retimbered, while the Tiro General had been newly timbered from the collar to 1090 ft. in depth. It had been possible to place guides in only one compartment of the Tiro General, from the collar to the seventh or 850-ft. level, to which it was necessary to lower the water before station pumps could be installed. Soundings indicated that compartments in the Tiro General were open to 1082 and 428 ft., and in the San Fernando shaft to 471, 488, and 586 ft. The water had risen to a point 140 ft. below the collar of the Tiro General shaft.. Pumping Equipment The steam plant at the Tiro General shaft includes one 300-hp., one 150-hp. and one 100-hp. Erie City water-tube boiler, and two 160-hp. Heine water-tube boilers. All but one of these boilers were supposed to be in good shape, but it was soon discovered that six years of idleness in a climate that is foggy for several months of the year had left them in poor condition. The compressed-air plant comprises one Nordberg cross-compound compressor with piston displacement of approximately 2500 cu. ft.of free air compressed to 96 Ib. per sq. in.; and another Nordberg cross-compound with piston displacement of 1235 cu. ft. of free air, to the same pressure. The main pump station is on the seventh level where had been installed a Prescott pot-valve plunger pump with capacity of 200 gal. per min.; also a Gould triplex plunger pump with capacity of 135 gal. per min., driven by a 6 1/2 by 10 by 12 in. steam engine. From the lower levels, the water had been raised to the seventh level by small station pumps and sinking pumps.

Jan 1, 1920

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier's Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By M. E. Prunty

Activity in coal preparation in 1967 was on the up-swing and all indications are that demands will be greater in the future. Feed tonnages to plants are increasing and a significant factor is that the top size being fed to plants is decreasing. This has been brought about by market demands, better cokability in some cases and emphasis on sulfur reduction in others. New plants are being built and some are in operation in the coal fields of southern Illinois. These plants are producing metallurgical coal in circuits that contain heavy medium cyclones and froth flotation on the - ½ mm x 0.

Jan 2, 1968

By R. J. Blackwell, J. R. Rayne, J. R. Henderson, W. M. Terry, D. C. Lindley

This paper presents the results of a laboratory investigation of the efficiency of water-solvent mixtures in recovery of oil. These mixtures may have the high displacement efficiencies characteristic of solvent floods and the high sweep efficiencies characteristic of water floods. Thus, the water-solvent process may increase the number of reservoirs in which a miscible-type displacement can be used profitably. The experiments on the use of water-solvent mixtures for recovery of oil were conducted to find the general applicability of the process. These studies demonstrated that, in flowing through sands, water and solvent segregated into a solvent layer on the top and a water layer on the bottom rather than flowing through the sands as a uniform mixture. Calculations based on the simultaneous flow of the water and solvent in layers were used to predict the effective mobility of the mixtures and the optimum operation of the process in steeply dipping, homogeneous reservoirs. As most reservoirs are not suited for the operation of the process under ideal conditions, experimental studies were conducted with sand-packed models scaled to represent more realistic reservoirs. These studies included the effects on recovery of oil of rate of injection, viscosity of oil, variations of permeablity within a formation and variations in water-solvent ratio. For the range of con-ditions studied, higher recoveries of oil were obtained with water-solvent mixtures than with water or practical volumes of solvent alone. INTRODUCTION A group of intriguing—because of their great possibilities—new oil recovery methods at the disposal of the petroleum engineer are the miscible displacement processes. These processes (high-pressure gas drive, en-riched-gas drive and LPG bank driven by methane) displace all of the oil from the portions of the reservoir swept by the injection fluid. The key question confronting the engineer applying one of these techniques to a particular reservoir is, "What fraction of the reservoir can be swept by injection of a practical volume of solvent?"." Intensive laboratory studies have been made during the past several years in seeking answers to the question of the sweep efficiencies which can be expected in solvent floods.' - These studies provided the answer that low-viscosity, low-density solvents channel and by-pass oil in sands with no dip. In horizontal sands, solvent flooding becomes less efficient as the viscosity of the oil increases, the recovery of oil at solvent breakthrough decreases and larger volumes of solvent are required to achieve a given recovery. More efficient displacement of oil by solvent is observed under certain conditions in sands with dip.".' If the permeability and dip of the sand are sufficiently high, gravity segregation of low-density solvent injected updip can prevent channeling. At rates of depletion below a critical rate,"." no channeling occurs. Unfortunately, in many reservoirs, the critical rate is so low that production of oil at rates below this rate is not economically attractive. And at rates over four times the critical rate, channeling is almost as severe in sands with dip as in horizontal sands. These findings pointed out that, for solvent floods to be generally applicable in recovering oil from all types of reservoirs, new methods of improving their sweep efficiencies are needed. Simultaneous injection of water with the miscible fluid was suggested by Caudle and Dyes7 as a method for improving sweep efficiencies. They theorize that water flowing with the solvent would decrease the effective mobility of the solvent and cause it to contact more oil sand. If, indeed, the water and solvent flowed as a uniform mixture, the process should have the advantages of the high displacement efficiencies characteristic of miscible floods and the high sweep efficiencies of water floods. Thus, the method (at least in theory) would greatly increase the number of reservoirs in which miscible-type displacements would be feasible. A research program was conducted to probe the technical feasibility of the water-solvent process. It

By Tribhawan N. Srivastava

The Henderson Mine started production in 1976 utilizing a unique, push-pull, mine ventilation plan. As the mine expands in size, the mine ventilation requirements will increase and a more comprehensive system for maintaining ventilation will be needed. A computer simulation study was completed and has resulted in a revised, systematic, mine ventilation plan which is being implemented as mine development proceeds. Based on the computer simulation study, the new ventilation plan takes into account mining of the orebody simultaneously from both the 8100 and 7700 production levels. Present experience and empirical data indicate that volumes of air needed to adequately ventilate both production levels cannot be obtained utilizing the existing mine layout. The total volume of air needed for the mine excluding haulage tunnel will increase from 708 m3/s (1 500 000 cfm) to 1652 m3/s (3 500 000 cfm), thus a new No. 5 exhaust shaft and connecting drifts are being developed to expand the mine ventilation system to service both production levels. The original ventilation plan for the 7500 haulage level was to bring air from the No. 2 and No. 3 intake shafts and exhaust it through the 94X raise to the 8035 exhaust level and then through the No. 1 exhaust shaft to surface. Control of air volumes in loading drifts was initially planned to be achieved by air doors and air curtains. Air doors on the 7500 level require large cutouts, expensive installations and constant maintenance. The computer simulation study indicates that air- flow in the 7500-level production drifts can be con- trolled exclusively by air curtains which are less expensive to install and more effective in regulating airflows than air doors. Air from the 7500 level can be exhausted through a new raise to the new 7635 exhaust level and then through the new No. 5 exhaust shaft.

Jan 1, 1982

By W. L. Doyle

SLAG weights were taken on a series of twenty-eight 6-ton bottom-pour heats. These weights varied from 573 to 1050 lb. Of these, four were chosen for study of the effect of cleaned and uncleaned foundry scrap on the variations of slag weights. Data regarding the make-up and results of the heats are given in Table I. For heat No. 3 the actual slag weight was checked, using the Mn-MnO calculation method-weight 1050 lb. [5,600 X 0.0055 = 30.80 heads and gates 6,000 X 0.004 = 27.00 plate scrap 800 X 0.0083 = 6.64 pig iron 450 X 0.0034 = 1.53 iron ore]

Jan 1, 1947

By Carl Henrich

I have read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: (a) Not determined in this analysis. (b) Not given in Mr. Eilers' paper. Oxygen ratio, A1 as base. I. 0 in acid: O in base:: 18.1:18.9:: 0.96:1 11. 0 in acid :O in base:: 18.7:17.5::1.06:1 Average: 18.4:18.15=1.01:l Oxygen ratio, AI as acid. I. O in acid: O in base: :23.2:13.8:: 1.68:1 11. O in acid: O in base::23.1:13.5:: 1.76:1 Average: 23.15:13.4 = 1.73:l By assigning to alumina the the of a base, Mr. Eilers deduces the formula 3Feo.-2SiOa + 4Cao.2SiO². The nearest approach to a simple formula expressing the average composition of these slags, which I can figure, is 9RO.Al2O3.6SiO2. Allowing a ratio of 4Feo : 5Cao, we have for this formula:

Jan 1, 1917

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU' OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l'l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum deposit, Eureka County, Nevada, occurs In a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusive. For samples from the 25000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8: 1 at 10-mesh, 8: 1 at 70-mesh, 6: 1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp 1s used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of ± 25%. The error distribution is not based. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1984

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)' or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

By W. Bonfield

The temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of polycrystalline Cu 1.9 wt pct Be have been measured for the solution treated condition, an intermediate condition containing G.P. zones and ?' precipitate and the overaged ? precipitate condition, in the range from -58° to 200° C. A transition in micro -yield behavior and a large temperature dependence were noted for the intermediate condition, which are interpreted in terms of the interaction of glide dislocations with two differently sized zones. In comparison the microscopic yield stresses of the solution treated and overaged conditions were less sensitive to temperature variations and are satisfied by the Mott-Nabarro and dislocation bowing theories, respectively. A determination of the temperature dependence of the yield stress of a precipitation hardening alloy has provided a powerful tool for evaluation of the operative deformation mechanism. There is a marked contrast between the effect of temperature on the yield behavior of a metal containing coherent zones or intermediate precipitates, which can be "cut through" by mobile dislocations, and a metal containing a dispersion of noncoherent particles, through which dislocation "bowing out" is the dominant role of deformation.' These studies have in general been confined to single crystals, as it was considered that similar experiments on polycrystalline material did not produce good data because of the lack of sensitivity with which the yield stress could be determined. However, this objection has been removed by the introduction of mi-crostrain techniques, with which the yield stress in polycrystalline materials can be measured to a strain sensitivity of 10-6. Such measurements have not only shown that the deformation of polycrystalline precipitation hardening alloys can be examined with the same detail as single crystals, but also that some unexpected results are obtained.' In this paper the results obtained from a study of the temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of a polycrystalline Cu 1.9 wt pct Be precipitation hardening alloy (Berylco 25) are discussed. The temperature dependence of the alloy was measured for three different conditions: 1) The solution treated condition (a supersaturated solid solution of a containing ~12 at. pct Be3) which is obtained by water quenching the alloy from 800° C. 2) The condition of y' intermediate precipitate, to- gether with some G.P. zones,' which is produced after an aging treatment of 2 hr at 315°C from the solution treated condition. (The alloy was cold rolled to 40 pct reduction prior to aging to minimize grain boundary precipitation effects.)4 3) The condition with equilibrium ? precipitate structure2 which is developed after an aging treatment of 24 hr at 425° C. EXPERIMENTAL PROCEDURE Tensile specimens of gage length 1 in. and with rectangular cross section of 0.18 by 0.06 in. were prepared from the solution treated, cold rolled alloy and were either resolution treated for 1 hr at 800°C, followed by water quenching, or aged for 2 hr at 315°C and 24 hr at 425° C to produce the desired precipitate structures. The microstrain characteristics of the aged specimens were determined at temperatures from —58" to 200° C and those of the solution treated specimens from -58° to 30° C. Each temperature was controlled to ± 0.2°C, which was a level of stability sufficient to eliminate thermal expansion effects from the measurements (~1.2°C temperature increase produced an extension of 2 x 10-6 in.). The microplastic behavior of the specimens in the temperature range below 82" C was measured with a standard Tuckerman strain gage,5 while at temperatures above 82°C a modified Tuckerman gage with a reduced strain sensitivity (4 x10-6 in. per- in.) was used. A load-unload technique was used to establish values of the microscopic yield stress. The specimen was strained at a constant cross head speed of 2 x 10-2 in. per min to a given stress level, at which the total strain was measured. Then the specimen was immediately unloaded at the same rate and any residual plastic strain determined. This procedure was repeated for an increasing series of stress levels until the microscopic yield stress was established by a direct measure of the stress to produce a residual plastic strain of 2 x 10-6 in. per in. (It should be noted that, as reversible dislocation motion occurs at stresses less than the microscopic yield stress,2 the plastic strain rate at this level was not constant.) In an ideal test, the microscopic yield stress would be determined from a continuous stress-strain measurement, rather than from a load-unload sequence, in order to eliminate mechanical recovery effects.6 However, it was found experimentally that mechanical recovery was negligible in Cu 1.9 wt pct Be at small plastic strains for all the temperatures investigated, as the microscopic yield stress was independent of the number of load-unload cycles employed (i.e., the values measured for specimens subjected to different numbers of cycles was within the experimental scatter determined for specimens tested in an identical manner). Therefore, it is reasonable to consider the microscopic yield stress determined in the load-unload

Jan 1, 1969

By Edwin F. Nelson, Charles Wirth, Gustav Egloff, C. D. Maxutov

The treatment of emulsified crude oils has been a problem for years in the petroleum industry. Until comparatively recently various methods of settling with and without chemicals have been used with indifferent success. Since wells have been acidized, emulsified crudes have been produced, which add considerably to the need for improved methods of treatment. The presence of large quantities of salts in the oils from acidized wells has presented several new problems to the industry. The use of hydrochloric acid in well treatments has caused the formation of sodium, magnesium, and calcium chlorides by interaction with the dolomitic limestones. These salts dissolve readily in the water normally present in the oil, and they are therefore incorporated in the emulsified oil. The crystalline salts have also been found in the oil, prevented from settling by protective films such as asphalt, resins and petrolatum. In some instances, free hydrochloric acid has been found. The salts may be present in crude oil in amounts ranging from a few pounds to over 1000 lb. per 1000 bbl. of oil. The transportation of these crude oils through pipe lines has led to erosive and corrosive effects, which are a tremendous cost to the petroleum industry. During 1937, more than 1,200,000,000 bbl. of crude oil was transported through pipe lines. Of this quantity approximately 10,000,-000 bbl. was water, and considerably more than 50,000,000 lb. was salts. If the crude oils were treated at the producing wells to remove the salts and water, an appreciable saving would be possible. The treatment would not be difficult, since it has been found that these oils are more easily treated at the time they are produced than after the aging and more stable emulsification that occur before they reach the refinery. Since great costs are involved in the use of these salty crudes at the refinery, treated oils essentially free of salts would naturally command a premium. The real added costs lie in refining salt-containing crude oils. Severe corrosion of refinery equipment in both topping and cracking installations has appeared in many refineries. Chemicals such as ammonia, lime and

Jan 1, 1938

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937