Search Documents

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm) . Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm). Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

Report of President The important fact of the year 1916 is that on July 25 contracts were executed by which the American Society of Civil Engineers because an additional Founder Society and arranged to make its permanent home in our building. The contracts provide for the construction of three additional stories to the building, the American Society to pay the cost tip to $250,000, this being considered equivalent to what each other Founder Society had contributed, the American Society to participate in the original Carnegie gift and have an equal share in the property with each other Founder society. The construction of the addition to the building is under way, $62,525.04 having been expended thereon in 1916. It has been found that, clue to war conditions and the advanced price of materials, the cost of the addition will be $300,000. The founder societies have been requested to assume the extra $50,000, one quarter each. This work is in charge of a Building Committee consisting of H. H. Barnes, Jr., Chairman, E. G. Spilsbury, Charles Warren Hunt and Charles F. Rand. At the request of the Founder Societies, important alterations were made in the lecture halls on the fifth floor of the building to make the same suitable for social functions of the societies. The cost, $6,642.08, was advanced by the United Engineering Society but is to be paid eventually by the Founders. The Library of the civil Engineers is being merged with the Library of the United Engineering. Society and the other founder societies. At the present time the membership of the four founder societies is 29,000 and of associate societies 23,000, so that a total of 52,000 engineers now have their headquarters in our building. The value of the real estate now owned by this Society is $1,647,171.16. This sum will be increased at the end of 1917 by the amount of the cost of the addition to the building.

Jan 3, 1917

By Arnold H. Kackman

At the Kaiser Cement and Gypsum plant near San Jose, Calif., one rod-ball mill has taken over the entire raw grinding function for the largest single cement operation in the West. Installed as part of a major overhaul performed on the plant by Kaiser Engineers, the new mill does the work of seven previous mills in feeding the plant's six kilns and keeping pace with its annual capacity of 8.5 million bbl of cement. Installation of the mill, which is the largest in the world, was started in December of 1966 and completed in April of 1967. The over-all modernization program surrounding the new mill has included the modification of existing crushing facilities; the building of new raw materials handling and blending facilities, new raw milling facilities, and new slurry handling facilities; and the installation of a digital-analog control system.

Jan 7, 1967

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By Donald Cummings

CERTAIN dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is. approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribu-tion, except that the upper limit of size retained in the air sacs is approxi-mately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been gen-erally conceded, however, that particles of harmful dusts smaller than ¼ to ½ micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are, not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to dis-regard them.

Jan 1, 1935

Jan 1, 1970

By R. J. Sherman, M. R. Achter

Creep rates have been measured for nickel at 1200°F in air and in vacuum, and related to the depth of surface cracks in the specimens tested in the two environments. The surface cracks were observed to grow faster in air than in vacuum in both short-time and long-time tests. Crack depths, however, could be correlated with creep rates only in the short-time tests. Although no cracks were observed in a relatively brittle Ni-Cr-A1 alloy creep tested at 1300°F, the appearance of alloy specimens fractured after interruption in creep indicated that there was a decrease of intergranular cohesion resulting from the diffusion of atmospheric gases into grain boundaries. PREVIOUS investigations1-3 have demonstrated that the effect of atmosphere on the high-temperature strength of nickel and nickel-base alloys may be reversed by changes in the stress or temperature of the test. At high stress and low temperature the creep-rupture life is longer in vacuum than in air, while at high temperature and low stress the relative strengths are reversed. A mechanism to explain this behavior was proposed based on two competing processes. Oxidation hardens and strengthens a metal, but adsorption of gas, by lowering surface energy, reduces the work required to propagate an intergranular crack. The controlling process is determined by temperature and stress. Basic to this mechanism is the concept that environment determines the ease of propagation of intergranular cracks and thus affects creep rate and rupture life. To explore the mechanism in greater detail, this investigation was undertaken to determine the effect of atmosphere on crack initiation and propagation rates in nickel1 and a relatively brittle Ni-Cr-A1 alloy.3 EXPERIMENTAL PROCEDURE The materials were the same as used previously. Nickel of 99.8 pct purity had the following impurity content: 0.02 pct Co, 0.03 pct Fe, 0.02 pct Mg, 0.03 pct Si, and 0.008 pct C. Rods were cold swaged from 1/2 in. to 3/8 in. in diam and machined into speci- mens with gage sections 1/4 in. in diam by 1-1/4 in. long. They were annealed in vacuum at 1600" F for 1 hr to achieve a grain size of 0.07 mm. The alloy was composed of 19.1 pct Cr, 3.6 pct Al, 1.7 pct Si, 0.57 pct Fe, 0.10 pct Mg, 0.027 pct C, 0.004 pct S, and the balance Ni. Sheet specimens of 0.500-in. width and 1.25-in. gage length were machined from 0.033-in.-thick strip and annealed in vacuum at 2000° F for 2 hr, resulting in a grain size of 0.036 mm. Large amounts of an intergranular phase were introduced as a result of the anneal. Creep tests on both materials, using equipment previously described by Shahinian; were conducted in air and in a vacuum of 1 x 10-5 mm Hg. They were continued to rupture and interrupted at various stages of the test. Although extensions were measured from dial gage readings of movement of the lever arm, it is considered that valid comparisons of creep rate may be made in this manner.l Two parameters were measured metallograph-ically* on longitudinal sections of nickel specimens interrupted during creep—the mean depth of surface cracks 2, and the density n as the number of cracks per unit length of surface. They were combined into one parameter by the relation p = n-d [1] As used here, p is equal to the total of crack depths per unit length of surface. RESULTS Nickel. It is well known that the incidence of intergranular cracking is increased with increasing rupture life. Indeed, it is evident in Tables I and I1

Jan 1, 1962

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By D. J. Christie, W. C. Hellyer

Three autogenous grinding flowsheets were considered as follows: 1) Primary autogenous grinding of a -8-in, primary crusher discharge to produce a product suitable for second stage pebble milling, or a flotation feed product in a single stage of grinding. 2) Intermediate autogenous grinding in which +4-in. rock media is screened from the primary crusher discharge and employed as grinding media to grind a tertiary crusher product to flotation feed size in a single stage.

Jan 8, 1972

By M. A. Roche

AST fall over half a million tons of ore and rock were broken in one blast at the open pit of the Hudson Bay Mining & Smelting Company&apos;s operation, at Flin Flon, Manitoba. The following particulars of the blast, and details of the preparatory work, indicate how an operation of this scope is carried out. The data given, in essentially the present form, were first published by The Canadian Mining Journal. The area blasted was 150 ft. wide and about 700 ft. long. A total of 123 tons of 50 per cent forcite gelatin, in 5 by 16-in. cartridges, was used for the charge. Drilling for the blast was started on May 29, and was completed late in August, requiring 1297 machine shifts for drilling only. Total footage drilled for the shot was over 5 miles of 6-in. hole. The main blast consisted of 232 holes spaced on 17.5-ft.

Jan 1, 1934

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate -free.1,4 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when, zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By W. Rostoker, R. P. Elliott, B. W. Levinger

Phase equilibria in the Ti-Mn-Mo system have been investigated in the composition range 100 to 60 pct Ti and in the temperature range 550 to 1150°C. Three out of ten isothermal sections are presented as well as seven vertical sections, projections of the beta space and the surface of incipient melting. A STUDY of the system Ti-Mn-Mo was undertaken as part of a program to aid in the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range 100 to 60 wt pct Ti (all compositions refer to weight percentages) and the temperature range 550" to 1150°C. A surface of incipient melting was constructed from measurements of a large number of alloys. In the binary system Ti-Mo,&apos; the high temperature modification of titanium generally spoken of as the p phase is stabilized to successively lower temperatures with increasing alloy content. There are no known intermediate phases, and complete miscibility exists between body-centered cubic titanium and molybdenum. The u solid solution is limited to less than 0.8 pct Mo at temperatures between 885" and 600°C. An equilibrium diagram for the binary system Ti-Mn has been published.&apos; Manganese behaves as a p stabilizer but undergoes a eutectoid transformation at about 20 pct Mn and 550°C to a plus an intermediate phase. The structure of this phase has been found to be isomorphous with the a phase FeCr." Accordingly, the phase is assigned the formula TiMn, although its actual location on the composition scale has not been determined and may well be not exactly at the equiatomic composition. In disagreement with ref. 2, the origin of the TiMn phase has been shown&apos; to be a peritectoid transformation at a temperature between 900" and 1000°C. A second intermediate phase occurs at the atomic proportions TiMn,. The structure of this phase was originally established by Wallbaum" as having a hexagonal lattice (C 14 type, 12 atoms per unit cell) isomorphous with MgZn,. In this work, the structure determination was confirmed and lattice parameters determined to be: a = 4.815 kX, c - 7.901 kX. Because of the extensive range of the P phase, the ternary system was suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." During the course of the investigation, this method was found applicable only to the P/a+P boundaries but not to P/P+ compound boundaries. Metallographic methods were used alternatively for delineating these phase boundaries. Preparation and Treatment of Alloys Over 70 alloys were prepared for the study of this system. Ten gram alloy buttons were arc melted in a nonconsumable electrode furnace using inert atmosphere protection, and a water cooled copper crucible. The construction and operation of this type of melting unit has been described.&apos; To insure complete solution of alloy additions, especially molybdenum, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" the ingots over. It was very difficult to obtain homogeneous melts in the region of less than 75 pct Ti because of the very high melting point of molybdenum and Ti-Mo master alloys and the comparatively low boiling point of manganese. Thus, the arc conditions for insuring complete solution of molybdenum were incompatible with the prevention of heavy losses of

Jan 1, 1955

One of the results of the work of the Committee on Precious and Base Metals is that the present Bulletin is as large as some of. the annual volumes of Transactions of the Institute, and we extend our. compliments and thanks to the Committee and express to the members thereof and to. the authors, who have so bounteously given of their time and information, the. sincere gratitude of the Institute. In order to get all these papers printed and distributed to the membership in advance of the meeting, it was necessary to divide the work between two printers. This accounts for the discrepancy in the pagination of the Bulletin; and we also ask the indulgence of our readers in case errors have crept into this preliminary edition during the period of unusual pressure. Program of the Butte Meeting.-The program of the Butte meeting will include six technical sessions for the presentation and discussion of papers and five half-clay visits to mines and metallurgical works. The following program is practically in final form, with slight additions which may be necessary later. Every effort will be made to have papers presented and discussed on scheduled time, so that members who are unable to attend the entire meeting may so plan their trip as to hear and discuss papers in which they are especially interested.

Jan 8, 1913

By Armand Bur, W. R. Reichenstein

Since coal is one of the largest cost items in the production of electricity, its analysis for heat value and composition has been the subject of intensive study. Sampling started with crude hand methods, out of the railroad car or barge or from moving conveyor discharge, and progressed to reliable mechanical in-plant sampling systems. The mechanical system takes its sample from a falling stream of coal such as a conveyor discharge or crusher discharge hopper. But this has a disadvantage in that the identity of the coal is lost. Coal is shipped to the user in train-loads, often made up of shipments from various mines. When the cars are dumped into hoppers and the coal conveyed to the power station, the various shipments become mixed because residual coal remains in hoppers and chutes.

Jan 5, 1959

Receipts, Jan. 1, 1914, to Dec. 31, 1914 Cash on hand, Jan, 1 1914 General Funds $1,843.54 Special Funds 1,039.00 $2,882.54 Initiation Fees $8,500.00 Annual Dues 44,060.84 Life Memberships 1,950.00 54,510.84 Sale of Transactions 4,798.87 Sale of Binding 10,029.06 Sale of Bulletins and Pamphlets 2,508.25 Sale of Special Editions 1,290.74 Sale of Advertising 8,783.29 Sale of Library Books 54.97 Sale of Pins and Fobs 347.65 Miscellaneous Sales 21.66 Space Released 5,943.00 Interest on Investments and Bank Deposits 230.15 34,016.64

Jan 1, 1917

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939