Search Documents

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By C. W. Wahsburne

Former studies of sedimentatry strata have been based upon the mineralogical and mechanical characters of the solid components, rather than upon the open spaces between them.

Jan 1, 1915

Jan 1, 1957

By R. F. Mehl

Jan 1, 1936

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in' the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By G. Willard Quick, John R. Freeman

Jan 1, 1930

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute. Since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1° to 2°C. per min. with or without slow stirring (Fig. 1). By this method the lead-rich end of the lead-antimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the' liquidus curve of the .binary alloys did not intersect at the eutectic temperature. An equivalent effect was observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent investigation by Pellini and Rhines,1 who determined the eutectic temperature to be 251.5°C. The observation that the curves of primary crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomenon by assuming the existence of a compound Sb4Pb. He felt that super-cooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3. the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature of 250° to 252°C. at a rate of cooling of about 6°C. per min. Abel, Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous, publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic contains only 11,4 to 11.5 per cent antimony. (Previous analyses by Stead4 in 1881 gave 13 per cent:) Weaver," however, reported in 1935 that cooling curves indi-

Jan 1, 1943

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By Thomas M. Drown

The process for determining phosphorus in iron now in most general use in the laboratories of iron and steel works, is, I think, the one proposed bv Mr. Emmerton." In this process the solution of the iron for precipitation by ammonium molybdate is effected by treating the iron with nitric acid, evaporating to hard dryness in a dish, taking up with hydrochloric acid and driving off the greater portion of the hydrochloric by nitric acid. This procedure accomplishes, first, the destruction of all the carbonaceous matters; and, second; it renders all the silica insoluble. Experience has proved the former—the complete oxidation of the carbon—to be absolutely essential; but the explanation usually given, namely, that unless the carbon compounds are destroyed they will have a solvent action on the yellow precipitate, I am inclined to

Jan 1, 1890

By Arthur F. Wendt

The earliest knowledge of copper-ores in the Southwest was derived from the Mexicans, who, in the latter part of the last century, discovered and worked the Santa Rita copper mines, now situated

Jan 1, 1887

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

Lester Guttman (General Electric Research Lab-boratory)—Seybolt has measured the thermodynamic activity of silicon in dilute solution in a iron. The anomaly which appears at 800 °C in the approximate range 1 to 6 wt pct Si is most naturally attributed, as Seybolt has done, to the existence of a region of

Jan 1, 1960

Jan 1, 1967

By H. O. Hofman

Jan 1, 1890