Search Documents

By R. E. Bedworth, N. B. Pilling

The corrosion of metals is one problem on which time and thought have been expended for many years. In the effort to avert the destructive action of a hostile environment, attention has been directed almost entirely to the conditions under which most metallic structures are called upon to perform, and the extensive and complicated phenomena attending the corrosive action of atmospheric agencies, acting at the ordinary atmospheric temperatures, have been studied, but there is unanimity of opinion regarding many fundamental facts. One neglected phase is the corrosive action of various gases upon metals exposed to temperatures considerably higher than the atmospheric range, and more especially the attack of atmospheric oxygen upon exposed metallic surfaces. That the problem is difficult is connoted by the practical dominance of industrial electric heating by alloys of one type (nickel-chromium). Proprietary interest may account, in part, for the paucity of information available upon even the most general factors determining the behavior of metals and alloys when exposed to such exacting conditions. The present paper gives some conclusions reached as the result of experimental work, extending over several years, on the mechanism and contributory factors of the high-temperature oxidation of a number of simple unalloyed metals; it is free from experimental detail and proof. High-temperature metallic oxidation may be considered as a phase of metallic corrosion. The scheme outlined below, in which corrosive agent and environment are the principal criteria, is one way of analyzing the several groups of corrosion phenomena. Erosion.—Disintegrating or destructive action by physical causes. Corrosion.—Disintegrating or destructive action by chemical causes. Low-temperature Corrosion.—Solid participating phases essentially immobile: (a) Gaseous agent; (b) liquid agent: action electrolytic and action non-electrolytic. High-temperature Corrosion.—Solid participating phases possess diffusive mobility: (a) Liquid agent; (b) gaseous agent: reducing gases, oxidizing gases. (1) Water; (2) miscellaneous elemental and combined oxygen.

Jan 1, 1923

By W. A. Tiller

The conventional techniques1 for determining the liquidus and solidus surfaces of an alloy system containing more than two components are extremely tedious to use and do not provide a complete picture of the equilibrium relations between solid and liquid alloys. These techniques are unable to yield "tie-line" information concerning solid and liquid phase equilibrium, a very important parameter in the solidification description of the liquid alloy and a very necessary parameter in the preparation of "zone-levelled" alloy crystals. The tie-line in a polycomponent system is analogous to the partition coefficient, k, in a binary system, it gives the composition of the solid, Cs, in equilibrium with a liquid of composition CL. That is, CS = kCL, where CL = [CO, c1,...Cn] denotes the concentrations of the n + 1 constituents, and k = [ko, kb ,...kon] denotes the gross partition coefficient for the elements between the two phases; thus, k is the tie-line in this system. To provide complete information concerning the two-phase equilibrium in a polycomponent system it is necessary to know both the liquidus surface and the gross partition coefficient. From these two the solidus surface is obtainable. The conventional techniques are unable to provide this information in other than a binary system so we must look elsewhere. In recent years considerable insight has been gained into the correct description of the liquid-solid transformation, 2,3 and controlled solidification experiments may now be designed to both facilitate and enhance equilibrium diagram studies. In the present paper consideration is given to two methods for obtaining the liquidus surface and the tie-lines in polycomponent systems. The methods to be described below deal with the solidification of an n + 1 constituent liquid alloy of initial composition [co, Co ,...Con], where the superscripts refer to the elements present and the Oth element is considered as the solvent in which the n solutes are dissolved. The general assumptions made in the treatment are the following: (i) the solid and the liquid at their interface are in equilibrium during the growth of the solid phase, (ii) there is no diffusion in the solid phase, and (iii) the liquid phase is completely mixed and is therefore homogeneous in concentration. METHOD I In this section a general experimental method will be described which, in principle, is capable of giving an exact description of the liquidus surface and tie-lines. Consider the unidirectional solidification of the liquid alloy specimens L cm in length (freezing either horizontally or vertically). Allow the sample to be frozen very slowly from one end, as indicated in Fig. 1, with complete mixing in the liquid, and then analyze the solid bar to determine its chemical constitution as a function of position, x, along the bar. Let Fig. 2 represent a possible distribution of the ith constituent along the bar. At the point x' the concentration of the ith constituent is C1/5(x'), and the average concentration of the rest of the bar between x' and L is given by C:(X' - L) where [ A(x) c1s(x)dx c1/s(x'-L) = f A(x) dx x * and A(X) is the cross-sectional area at x. In a similar manner. all the Cf(x' - L) may be determined. Thus, the gross artition coefficient k for liquid of composition [Cs(x - L),...Cs(X' - L)] is given by -ko= CUs')/Cos(x' - L)" k0 = csn{x')/cs(x'- L) During the freezing of a charge of length L, the liquid composition may vary over a wide segment of the phase diagram and the gross partition coefficient over this segment of the phase diagram may be determined from one, bar. Fig. 3 illustrates the magnitude of Cs(g)/C,' as a function of the fraction g of the bar which has Solidified.2 We can see that the concentration in the bar will vary over a range of about 15 wt pct for C,' = 10 wt pct and k0 = 0.5. It appears that 4 or 5 specimens would be adequate to study a simple binary eutectic phase diagram.

Jan 1, 1960

By John V. Beall

STREAM pollution caused by waste waters from mineral industry operations is a problem that has grown up with the industry. Its importance to each operator is dependent on the amount and type of waste he dumps into the rivers and streams; on whether this waste pollutes the waters sufficiently to make them unfit for potable water, irrigation, and conservation of wild life; and on whether this waste makes a safety or health hazard. Through the years our growing population and industry have made increasing demands on the mineral industries, the suppliers of the raw materials on which our industries are based; and we have met these demands at some sacrifice to the natural beauty and cleanliness of our country. However, that is often the unavoidable nature of the business, and along with the increased use of our

Jan 1, 1948

By G. Meyrick, H. W. Paxton

Observations on the tensile deformation of single crystals of austenitic stainless steels as a function of composition, orientation, and temperature are described and compared with relevant data for other alloys. Crystals free from second phases show sharp yield points followed by Lüders' extensions of up to 20 pct. The critical resolved shear stress is strongly temperature-dependent increasing fourfold between 423O and 77°K. A temperature-independent low rate of hardening follows the Luders' extension and is frequently associated with overshoot. Unlike pure metals where Proficse cross slip usually occurs at the end of linear hardening, this stage is terminated either by cross slip or by slip on the conjugate system, the particular node apparently depending upon initial orientation and composition. The presence of 6 ferrite or martensite has a profound effect upon the magnitude of the yield stress and the shape of the stress-strain curve. In experiments on transgranular-stress corrosion cracking of austenitic stainless steels in boiling magnesium chloride, several workers1'2 have shown that increasing amounts of nickel tend to reduce the probability of specimen failure. Reed and paxton3 have observed in single crystals that the macroscopic crack plane changes as the nickel content is increased. For 18 pct Cr-8 pct Ni, the crack plane is sensibly perpendicular to the applied tensile stress; for 20 pct Cr-20 pct Ni the crack plane is (100). The average crack-propagation speed is much lower in the 20 pct Ni crystals. Furthermore, the possible importance of stack-ing-fault energy in nucleation and growth of cracks has been suggested by a number of workers. While the general effect of variations in stack ing-fault energy appears to be quite well-correlated with observed variations in cracking characteristics, each of the theories assigns rather different detailed reasons for these effects. Because the stack ing-fault energy of austenitic steels is believed to be increased with increasing nickel content, and because some theories of trans-granular cracking postulate a mechanical stage in the crack propagation (rather than relying entirely on electrochemical solution), it appeared to be of some interest to investigate the mechanical properties of a series of different compositions of aus-tenite single crystals. These experiments were considered of intrinsic value in view of the relative scarcity of such data on fcc alloys. This paper gives the results of some experiments carried out with this aim in mind, and suggests various 'other experiments which may be helpful in future studies. The experiments are also of interest in view of the recent interest in obtaining higher-strength steels by control of the imperfection content of austenite; although the compositions are not directly comparable, the results are still probably valuable. Comparisons with experiments on other fcc alloy crystals are made where possible to see how well the general pattern of behavior is understood. EXPERIMENTAL PROCEDURE The alloys used in this investigation were vacuum-melted heats of nominally 20 pet Cr-20 pet Ni-60 pet Fe, 20pctCr-16 pct Ni-64 pct Fe, and 20 pctCr-12 pet Ni-68 pet Fe.* Analyses of the material are

Jan 1, 1964

By Mark C. Malamphy

AT present the Federal Government represents the only organization applying geophysical methods of prospecting in Brazil. The geophysical work of the National Department of Mineral Production, which will be described in the following pages, must be considered as a program of experimental work designed to demonstrate the applicability of the more or less "standard" methods of geophysical prospecting to various problems of economic interest in Brazil by means of practical examples of results obtained in certain typical areas. Our work is somewhat similar to that of the Imperial Geophysical Experimental Survey of Australia, but our task has been greatly simplified by the ever increasing number of technical publications relative to the theory of instruments and methods.

Jan 1, 1936

By P. M. Kelly, E. P. Butler

The stability of a 70/30 Mn-Cu alloy aged to peak damping has been investigated using electron microscopy, X-ray diffraction, and torsional pendulum measurements. Storage at room temperature or at 100" C causes a reduction in damping capacity. This is shown to be due to the formation of subdomains which "lock" the main domain structure and so hinder their movement. After storage the damping capacity can be restored by a retransformation treatment, which generates structures identical to those found in newly aged specimens. Plastic deformation by rolling also causes a decrease in damping capacity. In this case the damping capacity can only be restored by retransformation if the amount of deformation is less than about 5 pct. THE general metallography and structure of these high damping capacity alloys has been discussed in Part I of this work.1 Part II deals with some of the variables that affect the damping capacity. In particular, the stability of the damping capacity of a 70/30 alloy aged for 2 hr at 425° C and quenched has been investigated. The temperature sensitivity of the damping capacity of a 70/30 alloy aged for 2 hr at 450° C has been reported by Birchon.2 The damping capacity begins to decrease with increasing temperature, and is very low above the M, temperature of 125°C. The cubic — tetragonal transformation is completely reversible and there is no apparent thermal hysteresis associated with the change in damping capacity. Another important effect was first reported by Dean and his coworkers.3 They noticed a decrease in the damping capacity with time for specimens of a quenched tetragonal alloy. More recently workers at the Admiralty Materials Laboratory 4 have studied the stability of an aged 70/30 alloy. They found that the damping capacity decreased to half its original value after about 1000 hr at room temperature. EXPERIMENTAL The techniques used for electron microscopy and X-ray diffraction have been described in Part I. The damping capacity was measured by means of a torsional pendulum, using rectangular specimens, 3 by 0.3 mm with a 6 cm gage length. The specific damping capacity, S.D.C., was calculated as a percent amplitude decay in free vibrations over 10 cycles, starting at an amplitude which corresponded to a 700 psi surface shear stress. Because of the stress dependence of the damping,' the values obtained were about a third those reported for a 5000 psi surface shear stress.' RESULTS a) Effect of Aging Temperature. The effect of aging temperature on the damping capacity is shown in Fig. 1. The damping capacity reaches a peak of 12 pct after aging at 400° to 425°C) then begins to decrease as the volume fraction of a Mn increases. At higher aging temperatures the structure becomes cubic again with a low damping capacity. b) Stability of the Aged Structure. The damping capacity of the aged alloy decreases with time at room temperature. This process could be accelerated by storing at 100°C, when about 100 hr were required for the damping to fall to half its original value. The results of room temperature and 100°C storage, for times up to 1000 hr, are shown in Fig. 2. The damping capacity starts to decrease after about 24 hr at 18° C and 1 to 2 hr at 100°C. It was found, however, that the damping could be almost completely restored by retransformation. The specimens were held at a temperature above the M, for a short time, 250° C for 5 min, and then quenched. The values of damping capacity for specimens that were aged, stored, and then retransformed are shown by the full points in Fig. 2. X-ray measurements of the c/a ratio and hardness readings on the specimens did

Jan 1, 1969

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Thomas L. Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. GENERAL GEOLOGY Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisner1 in this region, supposedly partly or wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady [+] formation, also of Lower Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1940

By Carl F. Floe, John Chipman

THE system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100° to 1500°C., and pressures from about 20 mm. of mercury to somewhat above atmospheric. REVIEW OF PREVIOUS WORK The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as 02, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: [(MG) l 2M +G2 = 2MG K = Ma X Pa, [I]] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: [MG = Kl Pa,[2]] Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: [6Cu + SO2 = Cu2S + 2Cu20[3] K _ Cu2S X (Cu20)2 (Cu)6(Pso2)[4]] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: [8 =KI = Pte, or VSO2= K2 '~/PeO, [S]]

Jan 1, 1941

By H. LIVINGSTONE LMAN

A GOOD DEAL of information concerning flotation has come out during the patent litigation of recent years, and the legal situation has cleared considerably, to the satisfaction of Minerals Separation, Limited. Hence, Mr. H. Livingstone Sulman, one of the originators of the successful process of that company, felt at liberty to explain, on Thursday, Nov. 20, his experience and his views in a "Contribution to the Study of Flotation," before the Institution of Mining and Metallurgy. He did not give technical details. He dealt with the physical problems, so simple, as he remarked, that he had wanted 96 pages to express his views. He presented much data, partly new and based on observations of his own, bearing upon the very complex flotation phenomena in an instructive wav and made frequent references to the valuable researches especially of Prof. Edwin Edser and Mr. Emil Hatschek.

Jan 1, 1920

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By R. O. Williams

It is shown that Ni3Al precipitates homogeneously from nickel-rich alwminum alloys as plates on the (100) planes. Prior to actual precipitation a process occurs which is believed to be one of increasing short-range order. After precipitating the Ni3Al plates enlarge through competitive growth. Discontinuous precipitation can occur simultaneously with the above processes. Recent ideas of the origin of precipitation strengthening appear adequate to explain the hardness changes. REMARKABLY little appears to be known about the precipitation process in Ni-Al alloys in spite of their technical importance. This investigation originated to supply additional information about precipitation in general, this system in particular. Information on the structures and kinetics have been obtained through the use of hardness, X-rays, microscopy, calorimetry, and resistivity on high-purity alloys. PROCEDURES Six alloys, Table I, were prepared by melting carbonyl nickel and high-purity aluminum in alumina crucibles in vacuum and casting into 1-in. graphite molds. All rods were homogenized at least once at 1300°C for 24 hr prior to swaging and this was repeated on the first three alloys after 75 pct reduction. Alloy 4 could be reduced only 10 pct at 1000°C (probably in two-phase field) prior to fracture but 1/4-in. samples quenched from 1100°C were readily reduced cold. Alloy 5 was reduced 15 pct cold but failed on the next pass while alloy 6 of essentially the same aluminum content failed inter-granularly without apparent flow up to 1000°C. The alloys were heated in hydrogen at the elevated temperatures and formed thin, coherent aluminum oxide coatings which provided excellent oxidation resistance at lower temperatures. However, freshly prepared surfaces showed considerably less resistance at 500"to 700°C in air and apparently resulted in internal oxidation. As a consequence, low-temperature agings were carried out in evacuated tubes. RESULTS The isothermal hardening behavior of these alloys at 500"and 565C is given in Figs. 1 and 2. These results were obtained from samples cold worked 75 pct, recrystallized at 1000°C (1100°C for the 7.8 pct Al) and quenched in water. This recrystallization was used to give smaller grain sizes so as to obtain more uniform hardness values and the points represent an average of five readings. The electrical resistivity was measured on 1/16-in. wires quenched from 1000°C during aging at 495°C to give Fig. 3. The energy release and its rate are given in Fig. 4 for the 6.9 pct Al alloy during aging around 500°C. Inasmuch as this was a single run, its accuracy is not known but certainly the general shape and magnitudes are correct. The method used to obtain these results is described elsewhere.' Data for the aging at 600°, 700°, and 800°C of these alloys cold worked 50 pct are given in Fig. 5. Supplementary information from microscopy and X-ray diffraction have been included to indicate recrystallization, discontinuous precipitation and the appearance of superlattice lines from the Ni3Al. The hardness of these alloys as annealed, aged, cold worked, and cold worked and aged is given vs composition in Fig. 6. Those samples which were isothermally aged, Figs. 1 and 2, were reaged at 532°C and at successively higher temperatures for the indicated times to give the data of Fig. 7. These results as well as certain others, support the idea that the level of hardness reached for temperatures above 600°C are equilibrium values more or less independent of path. This being the case, the breaks in the curves would be the complete solution of the Ni,Al. The electrical resistivity versus temperatures for some of these alloys, both aged and unaged, is given in Fig. 8 along with those data from heating slowly (10 deg per day) to high temperatures. Interesting points include the lowering of the Curie temperature (the change in slope), the lack of any indications of a solubility limit and the large temperature coefficient for the Ni3Al. A slight break for Ni3Al around 100C shows up but this is not a Curie temperature as Ni3Al is not ferromagnetic down to -190°C. Metallographically both the nickel-rich solid solution and the Ni3Al appear very much like pure nickel. Profuse twin boundaries are present both

Jan 1, 1960

By C. Feng

HE sensitivity of twinning in molybdenum alloys containing 20 or more at. pct Re was reported by Dickenson and Richardson&apos; and Sims et a1.&apos; The latter3 also studied the effect of twinning on plastic deformation of these alloys. Recently, in this laboratory, the twinning planes in a series of Mo-Re alloys were successfully identified by tracing their boundaries on two known surfaces of the crystals, with the aid of stereographic projection. The nominal alloy composition and the results of the determination are listed in Table I. Metallic powders of molybdenum and rhenium with 99.9 pct purity were mixed, pressed and arc-melted into buttons under purified argon in a water-cooled copper hearth; the buttons were annealed at 2400 °C in vacuum (10-&apos;mm Hg) for 1 hr, remelted under argon and finally reannealed in vacuum at 2400°C for another hour. This treatment yielded a homogeneous alloy. Large-grain specimens devoid of subgrains were obtained with grain diameter varying from 1/8 to 1/2 in. A typical specimen weighed about 15 g. Orientations were determined by taking X-ray back reflection photographs for each grain on a polished surface of the specimens. Two surfaces were cut and polished; the angle between the two surfaces was measured with an accuracy of *2o. The twins were produced by compression in a hydraulic press at room temperature. Usually, several sets of twins could be obtained within each grain. Except in cases where no twins were formed, (Crystals 7, 8, and 9) the twinning planes were identified consistently as the (112) family over a wide range of alloying compositions and surface orientations of the crystals, as indicated in the stereo-graphic triangle in Fig. 1. The twins, however, were not broad enough to accommodate a conventional X-ray beam and no identification could be made of the twinning direction. Nevertheless, the direction must be one that lies in a plane of symmetry perpendicular to the twinning plane. There are only two such possible planes in a bcc lattice, namely the (110) and the (100) planes. Of these, only the (110) planes are perpendicular to (112), and the <111> direction is the intersection of the two perpendicular planes. It can thus be concluded that <1l1> is the twinning direction. The twinning elements of molybdenum have been reported as the (112) planes and the <111> directions,4 which are also the operative elements in other body-centered-cubic metals, such as W, a-Fe, and ß -brass.5 Thus, the present finding of the twinning elements in Mo- Re alloys supports the concept that twinning formation is mainly governed by the lattice structure. It is of interest to note that for specimens containing 12 at. Pct Re or less, no twins were found after being plastically deformed to as much as 30 pct reduction in height by compression, while for the 35 at. pct Re alloy, twins were formed with less than 1 pct deformation. This, of course, does not exclude the possibilities that for Re-Mo alloys containing 12 pct Re or less, twins could be formed under different conditions, such as at liquid air temperature or under impact loading. The present results, however, suggest that under the same conditions twinning is increasingly sensitive with increasing rhenium content. Consequently, the plastic strain at which twinning starts was found inversely proportional to the amount of rhenium in solid solution with molybdenum. This plastic strain necessary to cause twinning may be used as a criterion in the study of twinning characteristics.

Jan 1, 1961

By Susasn Leiter

THAT oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.1 Moore and Beckinsale&apos;s paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, .which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was diffi-cult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries.

Jan 2, 1926

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By C. M. Young

THE safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced. In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could he accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap, " would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of ½ in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in

Jan 8, 1919

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By H. R. Hendricks

THE ore of the Iron King Mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalchopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the nonsulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pct minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. DEVELOPMENT OF PRESENT FLOWSHEET AND MILLING PRACTICE The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (1) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pct, zinc 7.60 pct, copper 0.22 pct, iron 22 pet and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation was practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1947

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983