Search Documents

By Charles Luner

ALTHOUGH the kinetics of the atmospheric oxidation of tin have been studied,1-3 the kinetics in pure oxygen have not been reported. This note presents some results of the kinetics of the oxidation of tin foil in pure oxygen. The tin foil used in this investigation was 99.78 pct pure, the two major impurities being Pb (0.17 pct) and Sb (0.024 pct). The foil was degreased and air-dried prior to oxidation. The air-formed film was estimated by coulometric reduction4 of the surface oxides to be about 25A. The samples, which were in strip form and had a total geometric surface area of about 300 sq cm, were first evacuated at room temperature in an oxidation bulb to 1 X 10 -5 mm Hg and subsequently degassed for 1 hr at the temperature of the experiment. Spectroscopically pure oxygen was then introduced into the bulb. The rates of oxidation were measured by following the rate of pressure change due to oxygen consumption in a closed system, the volume of which was sufficiently large so that the pressure change during an experiment was 10 to 15 per cent of the total pressure. An oil-mercury manometer,5 with a sensitivity of 3 X x mm Hg (which corresponds approximately to 5 X 10 -7 gm of oxygen) was used to measure the pressure change. The oxidation bulb was heated by an oil-bath and controlled to within -10.3 C. The reproducibility of the rates was good, as determined by the coincidence of rates at 190oC for duplicate experiments. Fig. 1 shows the oxidation curves in the temperature range 168 to 211.5oC at 8 mm Hg pressure. The effect of pressure on the rate of oxidation at 190°C is also shown. The rate of oxidation was not markedly affected by changes in pressure in the range 4 to 9 mm Hg, except perhaps at the lowest pressure, 4 mm Hg, where after about 70 min there appeared to be a decline in the rate, as compared with the rate at the higher pressures. At the lower tem- perature, 168oC, and for short reaction times, it is difficult to distinguish between a linear relationship and a slight curvature in the oxidation rate. However, for longer times, there was a somewhat larger indication of curvature. The samples after oxidation were gold-colored in appearance. The oxide that was formed at 170°C was identified as a-SnO by reflection electron diffraction. This is in agreement with results obtained by other workers.6, 7 The rate data best fitted the logarithmic-oxidation rate law, w = K1n ln(1 + -t/to) [1] where w is the weight of oxygen consumed, t is the time, and K In, and to are constants. First estimates to were obtained according to the method of Taylor Thon8 and were then employed to obtain the best simuItaneous estimates of to and K In, that would fit the logarithmic expression. These estimates were found numerically, so that the residual variance could be minimized. The calculations were performed on an

Jan 1, 1961

By Castle. J. E., J. L. Gillson

In this chapter there is a wide difference in the meaning of some words used for rock and mineral names as defined by scientists and tabulated in the "Glossary of Geology and Related Sciences," published in 1957 by the American Geological Institute, and the meaning as used by the commercial producers of feldspar. It is necessary, therefore, to define these terms giving both the "scientific" and the "practical" definitions. There is no ambiguity about the name feldspar itself. This is a general term for a group of related minerals which are silicates of aluminum, combined with sodium, potassium and calcium. The feldspars are the most abundant minerals of the igneous rocks, and since these rocks make up the largest proportion of the earth's crust by volume (although not of the actual surface area of the continental land masses) the feldspars are the most abundant minerals of all. The igneous rocks themselves are classified on the basis of the variety of the feldspar present. The potash feldspars, which are called orthoclase and microcline, are the dominant minerals of the granites and syenites, and of their fine grained equivalents, the rhyolites and trachites. The plagioclase feldspars form an isomorphic series, of which the sodic endmember is called albite, and the lime endmember, anorthite. The members near the sodic end, albite, oligoclase and andesine are the characteristic feldspars of the granodiorites and diorites, and of their fine grained equivalents, the dacites, and andesites. These feldspars-orthoclase, microcline, albite oligoclase and andesine-are the feldspars used commercially. Labradorite, a member of the plagioclase group, in which the lime exceeds the soda in the chemical composition, is the common feldspar of the gabbros, anorthosites, norites, basalts and other so-called "basic" rocks. Although some attempts have been made to use labradorite as a commercial feldspar, none is now used except as an ornamental stone. The mineral anorthite is very rare. Since the feldspar in most of the common igneous rocks is relatively fine grained, and mixed intimately with other minerals, from which it can be separated cleanly only with difficulty, most masses of the common rocks cannot be used as sources for the feldspar contained in them. It is only the rarer types of rocks in which the feldspar is very coarse-grained, or ones containing very little of the iron-bearing minerals which are objectionable impurities in commercial feldspar, that are quarried to yield an acceptable product. The most widespread type of such a rock from which commercial feldspar can be produced, is that called "pegmatite." These rocks are dikes and bodies of irregular shape and of a size measured in feet or yards in most cases, rather than in miles. They are more commonly associated with granites, rather than with other coarse-grained igneous rocks. Many of them contain crystals of various minerals, including the feldspars, that are much larger than are found in the host rock, the granite, and in many there are large masses of feldspar that are sufficiently free from iron-bearing silicates so that products acceptable to the ceramic industry can be produced, in some cases simply by hand sorting. Most of this feldspar in pegmatites, however, does contain intergrown quartz up to 25 pct. Pegmatites are so important, not only as commercial sources of feldspar, but also of other minerals which are produced com-

Jan 1, 1960

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By AIME AIME

THE Engineering Education Committee of the Institute convened at the Engineering Societies Building on Feb. 18, .1929, with. E. A. Holbrook, dean of the Schools of Mines and Engineering, University of Pittsburgh, in the chair. STATISTICAL' STUDY OF STUDENTS IN MINING The first paper, a statistical study of the students enrolled in courses leading to a mining degree in 40 institutions, was presented by H. D. Keiser,, assistant editor of the Engineering and Mining Journal; who gave a brief outline of an article he was about to publish in ?that journal?. The complete article appears in the issue for March 30; 1929: To avoid repetition the results are summarized as follows: A request was sent to 42 institutions which give courses in mining' for the number of students enrolled as freshmen; sophomores; juniors, seniors and special students in mining for the years 1925-26, 1926-27, 1927-28, 1928-29. Two of these colleges replied that there were no students in mining. Students' enrolled in courses in metallurgy, geology and engineering, other than mining, were excluded from the statistics:. The statistics received were arranged in, four groups, according to the completeness of the information. One complete group of 25 institutions 'shows as follows:

Jan 1, 1929

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By Meredith Johnson

THE year 1924 saw little change in the production of oil and gas it either Pennsylvania or New York. In the early months of the year the price of Pennsylvania crude oil, $4.00 to $4.50 a barrel, was sufficiently high to cause operators to lay plans for rather extensive drilling opera-tions. But when, in August, the price dropped to $2.85 a barrel, there was no inducement for new work and drilling was curtailed. In spite of the curtailment, however, the combined production of the two states for the year showed a slight increase over 1923, the production being 8;859,000 bbl. in 1923, and 8,901,000 bbl.1 in 1924. The increased production was due entirely to. the continued development of flooding operations in the Bradford field, all other oilfields showing a decline for the year. TABLE 1. Production of Crude Oil in Pennsylvania and New York for the Last Ten Years a Production, Barrels Production, Barrels Year Year Pennsylvania I New York Pennsylvania I New York 1915 7,838,000 888,000 1920- 7,438,000 906,000 1916 7,593,000 874,000 1921 7,418,000 988,000 1917 7,733,000 880,000 1922 7,425,000 1;000,000 1918 7,408,000 809,000 1923 7,609,000 1,250,000 1919 8,137,000 851,000 1924 7,535,0006 1;366,0006 a U. S. Geological Survey figures. b Estimated. Much of the drilling in the southwestern part of Pennsylvania was done in search of gas. Natural gas in Pennsylvania is fast being recognized at its true worth and the increased prices allowed 'the gas companies for their product induced quite a bit of new work. The relative importance of natural gas compared with manufactured gas is shown in Table 2.2

Jan 3, 1925

By William Schriever

The flow of a gas-free liquid through a spherical-grain sand has been investigated by S1ichter.l By theoretical considerations involving a rather large number of approximations he arrives at the following flow-formula: V = CPd2At NLB{1 - m) where V is the volume of liquid delivered in time t through a cylindrical column of sand of length L and cross-sectional area A by a pressure-drop P when the sand grains of diameter d are packed to a porosity m and the coefficient of viscosity of the liquid is n. C and B are constants which were determined from geometrical relations; B was in reality a function of . Values of B(l — m) for various values of m were given in a table. In the same Annual Report of the U. S. Geological Survey, King reported the results of his experiments on the flow of water through porous media. He found that there was a departure of about 86 per cent. from a linear relationship between rate of flow and pressure, for a specimen of Dunnville sandstone for pressure drops not exceeding 60 cm. of mercury. The specimen was approximately 4 cm. in diameter and 5.1 cm. in length. Over the same range of pressure he found a departure of 45 per cent. for a specimen of Madison sandstone. For unconsolidated sands he found departures as great as 49 per cent. for pressure drops of 70 cm. of mercury; for pressure drops not exceeding a few inches of water he obtained a close approximation to a linear relation. He also investi-

Jan 1, 1930

By E. A. Anderson

THE copper-zinc phase equilibrium diagram has been the sub-ject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100° to 400° C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the com-position at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical con-ductivity and microscopical methods were used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-

Jan 1, 1934

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By Raymond Ward

IN the past few years several papers have appeared dealing with different aspects of the oxidation of dilute alloys, especially with respect to the formation of internal oxides or subscales. Subscale has been defined1 as that layer or zone of oxide particles precipitated in a matrix of metallic metal in which the oxide particles are dispersed uniformly and occur by diffusion of the oxygen inward from the metal surface. Alloys composed of a solvent metal more noble than the alloying elements are subject to subscaling or internal oxidation. In these alloys the solute must be present in such quantities that if the alloy is exposed to an oxidizing atmosphere at elevated temperatures, the rate of diffusion of the oxygen into the metal will be greater than the rate of diffusion of the solute outward. There is a composition range of the iron-silicon system that falls into this classification. Knowledge of the nature and rates of oxidation of iron-silicon alloys is of great commercial importance, but very little information of this nature is available. Darken2 recently has made calculations to show the limits of concentration of silicon for which subscales are produced in iron-silicon alloys; however, the main thesis of his paper was to analyze and to explain the already existing data. The purpose of this paper is to present the effect of com position, temperature, time, and atmosphere on the type of scale-metal layer obtained and to give some qualitative indication of the effect of these variables on the rates of oxidation. Since this paper is a study of silicon steels that are available commercially, extremely low-silicon and high-silicon alloys are not included. EXPERIMENTAL PROCEDURE The alloys used in the experiment were taken from heats of silicon steel that ranged in analysis from 0.70 to 5.8 per cent silicon. This composition range takes in most of the commercial silicon steels. In Table I are listed the compositions of alloys used. Other than iron and silicon, the alloys normally contained approximately the following impurities: carbon, 0.03 per cent; manganese, 0.07; phosphorus, 0.008; sulphur, 0.02; copper, 0.07; tin, 0.01, and from nil to a trace of chromium, nickel and copper. All of the alloys used were melted in open-hearth furnaces, except where otherwise noted, and were hot-rolled to 0.100-in. plate. Samples approximately 1/2 in. square were then cut from these materials. So that the surface conditions of the samples used for oxidation would be standardized, each sample was ground through 000 emery paper immediately before oxidation. Two different techniques were employed in carrying out the oxidizing treatments. One consisted simply of heating the samples with free access to air. In this treatment the samples were set on edge on a refrac-

Jan 1, 1945

By Cyril Smith

A COMPLETE discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.1 The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighbor-hood of 530° C. (1000° F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per. cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating-an all important factor where precipitation is concerned. Nehl,6 who apparently was unaware of Kinnear's work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solu-tion and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700° C. (1300° F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500° C. (930° F.).

Jan 1, 1933

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).' The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By E. P. Sadowski, L. P. Trudeau, C. R. Cupp

The apparent high radiation resistance of two varieties of maraging steel is described and an indication is given of some phenomena that require further study. Two aspects were included in this work: a) effects of neutron irradiation on the room-ternperature tensile properties of 18 Ni (250) maraging steel; b) effects of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5pct Cr-3 pct Mo maraging steel. Subsize tensile and impact test specimens were used. The 18 pct Ni steel was irradiated to a neutron fluence of 3.3 x 10 n per sq cm (>1 mev). The 12-5-3 variety was irradiated to two neutron fluence levels: 1) 1.5 x 10 per sq CTTL (>I mev) 2) 3.1 x 10'9nper sq cm (>1 mev) In all respects both varieties showed unusually high resistance to change in strength and ductility after neutron irradiation. There was no noteuorthy over-aging in fully aged specimens. The aged 18 pct Ni variety showed a 4 pct drop in yield strength upon irradiation with little or no decrease in ductility. The aged 12-5-3 variety showed a 5 pct increase in yield strength on irradiation with a very slight decrease in ductility. The impact transition of the 12-5-3 variety only increased 35 to 45 Co upon irradiation, and the shear energy fracture value for the subsized specimens decreased only half as much as expected frorn experience with conventional steels. THE development of new reactor concepts and nuclear technology now depends to a large extent on the availability of new alloys capable of operating in stringent reactor environments. One of the most important new types of metallurgical material that has been developed in recent years is the maraging steels. This type of alloy is notable for its remarkable retention of toughness at high strength levels. In the course of a research program which incorporated ambient temperature radiation effects studies to determine the mechanisms of strengthening of 18 pct nickel maraging steel,' it became evident that the resistance of the alloy to neutron-induced changes in mechanical properties should be studied. This paper is to present evidence for the apparent high radiation resistance of maraging steel. The experimental program was in two parts: a) Effect of neutron irradiation on the room-temperature tensile properties of 18 Ni (250) maraging steel. b) Effect of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5 pct Cr-3 pct Mo maraging steel, a cobalt-free alloy. EXPERIMENTAL PROCEDURE 18 Ni (250) Maraging Steel. Tensile test specimens were machined to the dimensions shown in Fig. 1 from $-in.-diam hot-rolled bar of the composition shown in Table I. All specimens were austenitized for 1 hr at 1500°F (815°C) in argon and water-quenched. Half of the specimens were then mar aged for 3 hr at 900° F (482°C) in argon. The specimens were irradiated in a fast neutron transformer rod at approximately 120°F (50°C) to a neutron fluence of 3.3 x 10 10 n per sq cm (>1 mev). The irradiation was performed in the NRX reactor of Atomic Energy of Canada, Ltd., at Chalk River, Ontario, Canada. In all cases, the thermal neutron flux was three times as high as the reported (> 1 mev) fluxes. The room-temperature tensile tests were performed with an Instron tensile testing machine operating at a crosshead speed of 0.05 in. per min. The loading frame of the machine, mounted in a hot cell, was remotely controlled. The specimens were tested either

Jan 1, 1968

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By Arthur Braid

THE war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be. obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find-in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the- manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain- grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferro-manganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within 'the last few years, and particularly since the war began, the great value of manganese in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 11, 1918

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913