Search Documents

By L. O. Howard

WHAT was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyère line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Falls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. .About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to handle the total output of copper in these small shells until the standard. Great Falls converters were substituted in June, 1914.

Jan 9, 1916

By W. R. Hudspeth

AS an outgrowth of its spodumene recovery operation at Kings Mountain, N. C., Foote Mineral Co. has been recovering a heavy mineral by-product. Foote leased this idle plant in 1951, reactivated it, using a new spodumene recovery process, and purchased plant and properties in October 1951. While the operation at Kings Mountain is primarily concerned with the production of spodumene concentrate, pilot plant work determined that the pegmatites also contained heavy minerals including cassiterite. Plans were made to recover the heavy minerals as a by-product and the flowsheet incorporated these facilities when the mill was modified for the new spodumene recovery process. The orebodies consist of spodumene, feldspar, quartz and mica. Apatite, tourmaline, and beryl are present in small quantities. The wall rock is pre- dominantly hornblende shist. The heavy minerals, including cassiterite, columbite, pyrrhotite, monazite, pyrite, and rutile represent about 0.2 pct of the ore. The fine-grained heavy minerals are disseminated throughout the dikes, apparently unassociated with the spodumene. The pegmatites are quarried and secondary breakage is by mud-capping and block-holing. Power shovels load into trucks transporting the ore to a coarse ore bin. A Telesmith 10x36-in. apron feeder delivers the ore to an 18x36 in. Traylor Jaw crusher adjusted to discharge -3 in. product to a primary conveyor. The conveyor delivers to a 4x5-ft Tyrock single deck vibrating screen using 3/4 in. cloth. The screen undersize is elevated to the crushed ore bin. Screen oversize goes to an Allis-Chalmers Hydrocone Crusher fitted with 4 in. concave and set to deliver approximately 66 pct minus 3/4 in. The crusher discharge returns to the primary conveyor. The crushing and screening installation has a capacity of about 60 tons per hour. Spirals The crushed ore is delivered at a rate of 350 tons per day to two 6x8-ft Hardinge Pebble Mills, equipped with 20 mesh Ton-Cap trommel screens. The screen oversize is pumped to a 12-in. hydroclone for primary desliming. The hydroclone underfl spirals. There is no heavy mineral loss in the hydro-clone overflow. The spirals bank consists of eight 5-turn Model 24-A Humphreys Spirals. The top port and the last four ports of each spiral are blanked, the remaining nine port splitters are adjusted to remove about 5 pct feed weight. The heavy mineral rougher concentrates are upgraded on a Deister Overstrom table. The spiral concentrates contain approximately 4 pct heavy mineral, and the spiral reject, which goes to another section of the plant for spodumene recovery, contains about 0.03 pct heavy mineral. There is an interesting feature in the spirals installation. An adjustable splitter mounted on the discharge boxes splits out a mica fines product containing very little heavy mineral. The mica product is cleaned by spiralling and screening. Thus the spirals recover two products; mica, and a heavy mineral rougher concentrate. Table Treatment The rougher spiral concentrate goes to a Deister Plato table, modified to receive a Deister-Overstrom No. 6 rubber cover with sand riffles. The table is operated with a 5/8 in. stroke, 270 strokes per minute, and a slope of 1/2 in. per ft from feed to tailings side. There is no slope adjustment from motion to concentrate end. Wash water consumption is relatively high, since the large spodumene grains tend to report with the fine heavy minerals. A middling band about 4 in. wide is maintained in order to produce clean concentrate. The middling, representing about 10 pct of table feed, is recirculated by air-lift. A band of concentrate grade coarse spodumene occurs just below the middling. This is removed and delivered to concentrate storage. The table tailing, containing approximately 0.7 pct heavy minerals, is returned to the spodumene feed preparation circuit. The heavy mineral table concentrates are approximately 45 pct cassiterite, 33 pct columbite, 14 pct pyrrhotite and 8 pct monazite, together, with some rutile, pyrite, and copper from blasting wire. Concentrate is collected at 24 hour intervals. and dried. If the concentrate remains in wet storage appreciably longer surface oxidation takes place which seriously interferes with the subsequent magnetic separation process. About 150 lb of heavy mineral concentrate is produced per 24 hours and shipped to the company's plant at Exton, Pa. for final separation into tin and columbium concentrates.

Jan 1, 1952

By H. B. Pulsifier

THE following report on the structure of copper is the result of work done in the laboratory of the Rome Wire Co. early in 1925. Previous work had indicated to the author that excellent results might be expected if a suitable technique in surfacing and etching could be developed. The resources of the Rome Wire Co. enabled this metal to be studied more intensively than previously, although none of the materials were investigated exhaustively. The material presented is hardly more than a preliminary summary of the most obvious character of the metal; a much longer research would have been necessary to solve many of the pressing problems connected with the casting and working of copper. The Rome Wire Co. has generously released the paper; to Dr. E. H. Darby, technical supervisor of the company, are due particular thanks for his appreciation of the importance of metallographic study of copper and for his effective support in the prosecution of the work and in making its publication possible.

Jan 1, 1926

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By James O. Elton

This paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a byproduct in the smelting of other metals. It is seen 'on the market in various forms, the most common being arsenic trioxide, the " white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports. Statistics of Arsenic Trioxide in United States.' Production. Consumption. Price Per Pound. Year. Tons. Tons. Cents. 1907..........1.010 5.471 5 1908,.........1,302 6,098 33/4 1909,.........1,007 4,600 2 7/8 1910,.........1,526 5,428 2 1/2 1911,.........3,081 6,539 2 1912,2........ 2,926 Closed at 4 7/8 Arsenic occurs in combitlation with sulphur and the metals in a large number of minerals. It is present in small amounts in many ores. In the roasting and smelting furnaces many of its compounds break down, liberating arsenic trioxide, which is volatilized and carried by the gases into the flue system, where a part is condensed and settles with the flue dust.

Jan 1, 1914

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By Robert Wamsley, W. E. Jones

ONE of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available, because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide, about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers. The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at-Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1945

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By H. K. Najarian

AT Josephtown, Pa., on the south hank of the Ohio River about thirty miles northwest of Pittsburgh, is the Josephtown electrothermic zinc smelter, which operates as a custom smelter receiving both domestic and foreign concentrates. Constructed in 1930, the plant was designed to produce zinc oxide and to process 124 tons per day of zinc concentrate obtained mainly from the Company's New York State mines. Zinc condensing equipment was developed in conjunction with the St. Joe electrothermic. furnace and commercial production of zinc metal started in 1936. Expansion of the plant and equipment during 1939 and 1940 brought the processing. capacity to upwards of 300 tons of concentrate per day; and the plant operated at peak capacity during the war years, earning the Army-Navy "E" award and three subsequent stars. A postwar plant expansion is now under way, designed to increase the capacity to 500 tons per day of concentrate, with an estimated daily production of 160 tons of zinc metal of various grades, about 100 tons of zinc oxide, and 425 tons of sulphuric acid as major products.

Jan 1, 1947

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30. Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a, community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo.

Jan 1, 1937

By Charles F. King

THE only investigations on record of the reactions occurring during the Bessemer blow are of charges containing a large percentage of manganese, with the exception of two partial analyses by Snelus and Barker of the. English method, where a low percentage of manganese was used. They do not give the analysis of the spiegel, nor do they report any graphitic carbon after the first stage of the process. Both report only traces of manganese after the first stage until the addition of spiegel. The slags corresponding to the samples of metal were not analyzed.

Jan 1, 1881

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

By Carel Robinson

THE little coal mine at Otsego, in the Winding Gulf field of southern West Virginia was dying. In the history of coal mining thousands of mines have been successful at first, but usually a change occurred and profits ceased. Often be change was so gradual and extended over such a length of time that the fundamental causes did not stand out in sharp relief and their significance was not realized. Studies often reveal that the cause for failure was in the arteries that connect the producing places with the mine entrance. Profits continued so long as the working places were close to the tipple and while the thrill of newness aid ease of access resulted in effective supervision from day to day. The air- way and haulageway, the wire line and manway, may have been sufficient when the distance from the entrance was a few hundred feet, but were inadequate when this was extended for thousands of feet.

Jan 1, 1937

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg. Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Address wanted. '76 ¦ABADILLA, QUIRICO A. Geol. Dept. Cia. Mexicans de Petroleo "El Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio,] [ ]

Jan 1, 1925