Search Documents

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By Alonso Marchena, William Martínez, Joel Otero

En Arequipa, Moquegua y Tacna se han definido diversos arcos magmáticos. En los arcos jurásico, paleoceno y oligo-mioceno ocurren pórfidos de distintas características, los cuales presentan diferencias litogeoquímicas (LaN/YbN>20, Sr/Y>40, Eu/Eu*>1, U/Th>0.27, NbN/TaN>0.7). Estos parámetros pueden ser utilizados como guías de exploración, ya que son anomalías desde el punto de vista litogeoquímico. En caso no haya mineralización visible (depósitos ocultos), el empleo de estos trazadores en unidades ígneas (diques, cuerpos subvolcánicos e intrusivos) puede señalar la probabilidad de encontrar depósitos en profundidad.

May 22, 2019

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

By T. J. Serenko

The epithermal deposit is hosted by Tertiary volcanic rocks that lie between mid-Miocene normal faults of the Northern Nevada Rift. Petrographic, laser-ablation and metallurgical observations suggested that the gold occurs in two principal forms: native (and electrum) and disseminated in arsenopyrite. It was proposed that gold is distributed between two parageneses with distinct mineralogical associations. Detailed downhole geochemical study supported the observations. Concentrations of Au, Ag, As, Sb and Se were determined from drill core and reverse-circulation cutting composites and contoured on cross-sections. Gold was indeed shown to have a bimodal distribution with the two parts separated spatially and perhaps temporally, implying that two separate genetic processes acted to concentrate gold at Mule Canyon

Aug 1, 1995

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By Özgür Bezgin

This paper presents observations on the installation of drilled shafts from two construction projects and an academic study with experimental and analytical parts. The construction projects involved the use of pressurized drilling methods. The experimental part of the academic study involved the use of the auger drilling method. The analytical part of the academic study investigated the effect of drilling methods on the soil-structure interaction and the behavior of drilled shafts under lateral loads. The concept of ?free-length? is introduced for the lateral load design of pressure-drilled shafts that are thought to be fully embedded within a soil media. The academic part of the study presented herein was conducted in Rutgers, the State University of New Jersey.

Jan 1, 2009

WHEN making comparisons of the efficiencies of different grinding and crushing machines it is desirable to be able to estimate the work actually done in crushing the ore from a given size of feed to a given size of product, the screen analysis of both feed and product being determined. Messrs. Klug and Taylor, in a paper on this subject, published in the monthly journal of the Chamber of Mines of WA, 31st January, 1906, have described a method adopted by them in calculations made in connection with a series of trials of grinding pans. Their methOd is based upon the assumption that if a quantity Q of material consisting of particles of average diameter x be crushed down until the average diameter of the particles is y, then the work done in grinding is proportional to Q x. There is no theoretical basis for this assumption that the writer is aware of, and it does not appear to satisfy the fundamental conditions necessary. If the material be further crushed until the diameter 2 becomes Z, the additional work done is measured. The work done in crushing from diameter x to diameter Z in one operation is proportional to Q x:, and therefore we ought to have zx2 y2 x2 Q-+Q-=Q-. y2 Z2 Z2But these expressions are not in general equal to one another. In other words, according to the theory underlying this method, if we crush from diameter x to diameter y, and then from diameter...

Jan 1, 1909

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By A. W. Bester

Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Eng.) Cullinan Diamond Mine currently handles 3.2 million tons of run of ore per annum. This is done by means of an underground train system, which is located at 763 metre level. Four trains, one in each quarter of the pipe, collect ore from passes and transport it to centrally located tips in the north and south of the pipe. The ore is then split into coarse and fine fractions. The coarse fraction proceeds to the primary crushers in the north and south. Historically, mining has been performed in such a manner that an equal amount of ore has reported to each quarter of the pipe. However, the tonnage profile of the mine will change such that the ore will no longer be split equally. For approximately five years the majority of ore will report to the east and thereafter most of the ore will report to the western portion of the mine. This will continue for the remainder of the current infrastructure level?s operational life. Coupled with this is the fact that the mine is aiming to increase its annual production to 3.8 million tons. The result is that the current ground handling system cannot accommodate the additional tons and therefore alternative ground handling options have been investigated. The continued existence of Cullinan Diamond Mine relies on finding a system that can economically handle the additional tonnage. Three options were investigated. Firstly, a train option, which would be an upgrade of the current system, was investigated. Two truck options were also investigated, the first of which was a conventional truck option. The second truck option was more interesting and involved an unfamiliar Combi truck system. The truck options were investigated primarily due to the fact that the block height of the BA West (a new production block) can be increased by 15 meters if a truck option is decided upon. This would create a significant increase in revenue for the BA West project. Each of the options was assessed in terms of its physical and financial feasibility. In terms of the physical constraints, it was found that all three systems could work. Detailed financial analysis indicated that either of the two truck options would be a suitable solution. However, due to the limited information regarding the Combi truck option, it should be further investigated. This applies particularly to the actual running and maintenance costs for the equipment.

Jan 1, 2005

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

Magnetic separation is an age-old technique for mineral beneficiation operations. The existing mathematical models for magnetic separators are quite complicated, and it is very difficult to measure the theoretical separation efficiency. The connectionist approach of modeling, to establish the relationships of the inputs and outputs, is preferred for this kind of problem. Experiments were carried out on a high-intensity roll magnetic separator to develop a database using four input variables (magnetic flux intensity, particle size, splitter position and roll speed) and two output variables (weight recovery and Fe recovery). The artificial neural network (ANN) and statistical methods (MLRG) were used to model the magnetic separation process. For the ANN, the regression coefficient (R2) values between the predicted and measured results were 0.89 and 0.94 for Fe recovery and weight recovery, respectively. Compared to ANN, the multivariable linear regression analysis showed inferior performance in predicting the weight recovery and the Fe recovery. The ANN models for the roll magnetic separator can predict the separation efficiency up to an acceptable limit. These models can be used to modify the operational parameters at mineral beneficiation plants to minimize the effects of variations in the raw material characteristics.

Jan 1, 2009

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By Roberto Busato Belger

- Fertilizer Business Overview - Supply -Demand Balance in the World - Supply -Demand Balance in Brazil - Brazilian Market Growth Opportunities - Fosfertil Operations - Fosfertil Expansion Plan - Salitre Project - Project Characteristics - Technical Challenges and Solutions - Technical Support Studies Conclusions

May 1, 2010