Search Documents

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

The New South Wales coal industry is a highly mechanised well organised industry which has developed from an annual production of slightly less than 13 million tons in 1950 to over 33 million tons in 1969. Although continuous miners were not introduced into the mines until 1950, by Jillle 1969 the percentage of coal won by these units was 87.3. The paper describes mining conditions in the various coalfields of the State, their complexities and problems and how these have been dealt with. The introduction of fully mechanised long wall faces has presented a challenge which has been accepted and descriptions of systems in use are discussed. Major expansion of the industry is anticipated to meet the requirements of the growing Australian steel industry, for local power generation and to meet the increasing demands of overseas markets.

Jan 1, 1971

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By Edward W. Parsons

The transverse force developed by expansion-shell rock-bolt anchors on the wall of a drill hole as the bolt is tensioned was measured by the Bureau of Mines using a device specially designed and fabricated for attachment to a universal testing machine. Load cells equipped with electrical-resistance strain gages provided the data from which the transverse force, in pounds, was calculated. Seven different expansion-shell anchors were tested, and the ratio of transverse force to bolt-tension load was found to range between 0.98 and 1.94 to 1.0. The drag load appeared to be the major cause of the transverse-force variation, but the relative effects of individual factors that affected the ratio between the transverse force and the bolt tension were not determined.

Jan 1, 1968

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By David R. Macedon

"Through the years, a wide variety of dust control methods have been utilized at mineral processing operations. While some have been successful, many have been highly ineffective. Dust Control systems currently in use include baghouse systems, fog systems, surfactant spray systems, and foam dust suppression. While baghouse systems can be effective, they are capitalintensive and costly to operate and maintain. Chemical dust control programs can be very effective. However, if applied incorrectly, they can have detrimental effect on mineral recovery. Thus, many operations utilize a combination of baghouses and water, often with limited success.Recent advancements in surfactant and polymer chemistry have resulted in substantially improved chemical dust suppression programs. These products range from non-corrosive surfactant/humectant combinations for road dust control to foam-based systems for crushers and transfer points, to advanced polymers for pile binding and soil stabilization. These advances are discussed in detail, citing results from fieldwork in the precious and base metals industries.INTRODUCTIONThe global nature of the mineral processing industry presents a unique set of challenges. Traditional thinking would tell us what works in one place should work in another. This could not be further from the truth in the area of dust control. We learn very quickly that there are a number of factors that can affect the efficiency and success of a dust control program and that these factors are not all chemical or equipment related. Some of these factors include facility maintenance, product selection, water quality and characteristics, and economic considerations.What has been learned from past experience is that each mineral processing plant presents a unique set of factors that will affect the ability to create an optimal dust control program. This paper presents a myriad of treatment options that will highlight the advancements in chemical dust suppression products and equipment."

Jan 1, 2004

By Donald James Butler

Problems resulting from underground mines in three inactive mining districts in Colorado were investigated. The purpose was to determine how these problems could be reduced or eliminated in new closings -- essentially by benefitting from lessons of the past. Mines in Leadville, Westcliffe and the Cripple Creek-Victor districts were evaluated. Two basic types of problems were found to exist in the districts: environmental degradation and hazardous conditions. Environmental problems result largely from acid and toxic drainage from the runes and from leaching of surface waste rock piles and mill tailings impoundment. The acid drainage contributes high levels of metals to streams and deposits sediment in the stream bottoms. Erosion of waste piles is a lesser problem. Hazardous conditions from open or improperly sealed mine shafts and adits, mine subsidence pits, and from deteriorating and unsafe surface structures are common to the three districts. These problems become worse with the ravages of time and vandalism. Engineering solutions which would correct or reduce many of these problems are presented. These recommendations should also be applied to new mine closures, however, more basic changes are needed to effectively implement improved mine closures. The changes must take place in the areas of legislation, mining practices and education. Legislated regulations should realistically reflect the needs of both the mine operators, protection of the environment and the best interest of the general public. Benefits should be provided for compliance with regulations instead of penalties being assessed for noncompliance. Hazardous conditions and environmental problems associated with mines can be alleviated through improved mine design and effective cloning procedures. Education should provide an appreciation by the general public of past and present problems facing mine operators. This will result in an improved mining climate which, in turn, will insure a continuing supply of minerals to meet increasing needs.

Jan 1, 1983

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012