Search Documents

By R. John Caulfield

The primary water supply system for the City of San Francisco and adjacent peninsula areas consists of aging and deteriorated pipelines crossing under the San Francisco Bay (the Bay). This system is highly vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The Bay Tunnel Project will replace the existing system with a 8-km-long (5-mi-long) tunnel underneath the Bay. The tunnel will be constructed using earth pressure balance methods and will have a two-pass lining system of precast concrete bolted, gasketed segments for initial support, and a welded steel pipe final lining. The project challenges include tunneling through both soft ground and rock conditions without any intermediate shaft access over the entire alignment. Seismic performance criteria include maintaining service flows after a large earthquake.

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

Sulfidisation Promotion Effect of Ammonium Sulfate on the Flotation of Copper Oxide Ores

Sep 13, 2010

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931, The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results off other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time Each sample was taken will also be retorted. History of Survey The Bureau of Mines made its first survey of motor gasolines sold throughout the United States in 1915,4 a second in 1917,0 and a third in April, 1919.0 These three surveys showed that during each 2-year interval the motor gasoline had become notably less volatile. In order

Jan 1, 1932

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By D. Xie, S. Sun

An overview of recent development of CSIRO?s Multi-Phase reaction models will be presented with examples comparing the calculated physico-chemical properties of metallurgical slags with the existing experimental data. The paper will also outline the development of a kinetically based model for molten bath reactors and its application to submerged combustion of coal in a slag bath as well as the reaction between the slag and injected coal particles. The plume model combines established models for the combustion of pulverized fuel with models for the growth and rise of bubbles from a lance or tuyere. This model predicts the extent of de-volatilization and combustion of the coal in the plume, the utilization of oxygen and the exchange rate of oxygen between the gas and the bath as well as the heat transfer rate between the gas bubbles and the bath. The slag reduction model brings together the recently measured rate data and fundamental understanding of the kinetics of CO-CO2reaction with iron oxide containing slags and predicts the changes resulting from injection of coal particles into molten slags. The top-space model covers reactions between gases and molten droplets in the post-combustion zone, where heat and mass transfer between phases results in higher utilization of the fuel values in the partly oxidized gases and transfer of heat to the molten bath. Keywords: Phase equilibria, viscosity, electrical conductivity, slags, kinetics, reaction rate.

Jan 1, 2004

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By Gary R. Peterson

In order to determine the potential availability of alumina to feed U.S. aluminum smellers, the Bureau of Mines evaluated 39 domestic mines and deposits of bauxite, alunite, and high-alumina clays and found that substantial increases in alumina prices would be necessary before nonbauxitic deposits could become competitive with bauxite. As part of the study, a price-tonnage relationship was developed indicating the quantity of alumina that could be produced from known deposits at various alumina prices and at a 15-pct discounted cash flow rate of return on the required capital investment. All capital and operating costs were calculated in August 1980 dollars. The domestic bauxite reserve base comprises three operating bauxite mines in Arkansas containing some 15.6 million metric tons of recoverable alumina (A1203). Ferruginous bauxites, clays, and alunites fall into the subeconomic category of identified aluminum resources, which, at the demonstrated level, contain over 4,000 million metric tons of alumina that are estimated to be recoverable. Analyses indicate that, at the demonstrated resource level, a total of some 15.6 million metric tons of alumina, all from three active Arkansas bauxite mines, is recoverable at a 1980 price of $0.12 per pound ($264 per metric ton) of alumina. A price of approximately $0.26 per pound ($573 per metric ton) of alumina would be required for production of the total U.S. resource. Thus, unless new technological breakthroughs occur that could make alternate sources of alumina competitive with bauxite, U.S. dependence upon imported bauxite will continue to increase.

Jan 1, 1981

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980