Search Documents

By Raja V. Ramani

Discussion in this section of the Handbook is limited to the working environment of miners, the mine workers themselves, and the machines used in mining (Fig. 11.0.1). The contents emphasize personnel health and safety aspects and engineering design and control practices to ensure a productive health and safety environment. Reference is to the health and safety of the individual miners as well as to the safety of the working environment. This Handbook also contains references to health and safety regulations in Chapter 3.2 and environmental protection in Chapters 3.4 and 7.3.

Jan 1, 2008

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By Jeremy Morris

The city of Indianapolis has more than 25,000 homes currently on septic systems. Many of these systems do not function well because of their age and surrounding soil conditions. As Indianapolis has worked to eliminate septic systems and install sanitary sewers in large unsewered areas on the north-west side, capacity of the existing Belmont North Interceptor (BNI) became a concern. The BNI system currently services an area of approximately 80 km2 (31 sq miles) located within the northwest quadrant of the city (Fig. 1). Monitoring of the existing interceptor indicated portions of the sys-tem flowing half- to two-thirds full during dry weather conditions and surcharging during some wet weather conditions. Further analysis of the BNI based on growth projections coupled with increased sewershed yield resulting from the city?s septic tank elimination program (STEP) indicated dry-weather flows could potentially triple over the next 20 years. Based on these modeling results and current wet weather capacity issues, the city determined further STEP projects could not be performed within the BNI service area until

Jan 1, 2011

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

The Electricity Generating Authority of Thailand (EGAT) Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 Mt of lignite annually to generate 2400 MW of electricity. The surface mine pit covers is 4 km by 7 km with mining depths ranging up to 260 m. A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope occur often due to the existence weak planes such as faults and bedding, and the weak mechanical properties of the rocks. Hence, 200 m to 300 m boundaries of rock block including coal seams are left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope. Moreover, the mined coal seams are very thick and their thickness range from 15 to 30 m.This paper discusses the application of multi-slicing highwall mining system with stowing to this very thick coal seam left around large pit slopes by means of numerical analysis.

Dec 6, 2010

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

THE Talisman mine is situated on the Waitawheta (pronounced Wytaffetta) river just above its junction with the Chinemuri (pronounced Chinnemurre) river near Karangahake, NZ. The explored reef-bearing portion of the claim includes the angleformed by the junction of the rivers and extends southwards for slightly over a mile (See Plate V.). The country is mountainous both rivers flowing through precipitous gorges.The trig. station on Karangahake mountain is almost directly above the workings on the Bonanza section and is 1680 ft. above river level, the adit from the gorge giving 1200 ft. of backs measured vertically. The officers of the N.Z. Geological Survey are engaged in a detailed survey of the Waihi district and the rocks of Karangahake are under examination. The rocks of the district are andesites and dacites much altered and silicified. One of these exhibits a columnar structure in the mass in the Waitawheta gorge near the surface workings on Taukani hill, also on the southern bank...

Jan 1, 1912

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

Bioleaching Metals from Waste Printed Circuit Boards and the Shapes of Microorganisms

Sep 13, 2010

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By Jonathan Peck, Doug Pollitt, Malcolm Scoble

Over the past 5 years the Department of Mining and Metallurgical Engineering, McGill University, has been involved in the performance monitoring of both percussive and rotary drills. Studies conducted in open pit coal and iron ore mines using microprocessor-based research and commercially available instrumentation resulted in the monitoring of at least 6 performance parameters while drilling vertical production blastholes.

Jan 1, 1991

FOR rapidly marking in geological and topographical features on parish plans, the author has used the Veeder cyclometer with very satisfactory results. A simple Veeder cyclometer, usually retailed at cycle depots at 4s., is fixed to the axle of the front wheel of an ordinary bicycle. The cyclometer is desigued to read in miles and tenths of miles, which are recorded through gearing actuated by a striker on a spoke of the bicycle wheel engaging one of the vanes of the cyclometer once every revolution.By using 80 strikers the reading would be in chains and tenths of chains; therefore the use of 8 strikers gives the reading in chains, utilizing all the figures. The cyclometer is designed to be placed on the right-hand side of the bicycle, and takes up a minimum of space, being only about the size of the top joint of the thumb. With some makes of cycles there is insufficient clearance, so the cyclometer must then be placed on the left side, and the 8 strikers made to engage the top vanes, as shown in the sketch (Fig. 1).Very accurate readings can be obtained by this instrument. The author has found by numerous tests that the maximum error...

Jan 1, 1916