Search Documents

By D. F. Hewett

CONTENTS PAGE Introduction 1 Geologic features of eastern Oregon 2 Geology of the Sumpter quadrangle 2 Rocks older than the ore deposits 3 Rocks younger than the ore deposits 8 Lodes of the Sumpter quadrangle 8 Areal distribution 8 Geologic distribution 9 Major features of the veins 9 Mineralogy and texture of the veins 13 Ore deposits zonally disposed around the Bald Mountain batholith . . . . 13 Summary of mineralogy and texture 32 Zonal relations 33 Ore deposits zonally disposed around Greenhorn Mountain batholith . . . 36 Zonal relations 37 Relation of textural features to zonal arrangement of veins 37 Summary of zonal relations 38 Comparison with similar districts 39 Outlook for the district 40 INTRODUCTION IN an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By Kelvin K. Wu, George H. Gardner

On July 24, 2002, a nonfatal entrapment accident occurred at the Quecreek #1 Mine, Black Wolf Coal Company, when an active mining section inadvertently cut into a flooded abandoned mine. This incident, and the dramatic rescue which ensued, brought national attention to a common problem in the coal mining industry. Since 1995, there have been more than 100 inundations at coal mines in the United States. Unavailable, inaccurate, or incomplete mapping of older abandoned mines is typically responsible. Serious problems associated with accidental discharges of fluid mine waste material (slurry) and water from coal refuse disposal facilities have resulted from similar causes. Recent problems related to the inaccurate location of old abandoned mine works have increased the interest in the use of conventional and emerging drilling and geophysical techniques for detection of air-filled and water-filled cavities. The United States Congress has committed significant funding toward investigating the applicability of these technologies. MSHA actively promotes the use of the best available technology to minimize the significant adverse safety and environmental consequences associated with unplanned breakthroughs and inundations. This paper provides background information and a general summary of the MSHA-sponsored field demonstration projects which are currently in progress. Potential benefits and limitations are discussed. The need for field verification/ground-truthing is emphasized. Under appropriate conditions, geophysical methods can be effectively integrated into a comprehensive field exploration program.

Jan 1, 2005

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

THE following notes were accumulated during the years 1905 to 1911, when the writer was employed at Stannary Hills. The writer's duty took him over the underground workings daily. In odd moments the geology of the surrounding country was worked out. As the time for this purpose was limited, many interesting points had to be left, untouched. The faulting system in the mines was of such a puzzling character that it seemed as if the geology of the surrounding district might throw some light on it. Dr Jack, in 1907, reported on these mines for the shareholders, but came to no definite conclusions. Unfortunately, the writer has not had access to this report for many years. At the time of his visit the larger develbpments in the Ivanhoe and, Kitchenen orebodies (see Fig 1, B2) were only being opened up. Mr. H. Herman mentions Stannary Hills on p 320, Proceedings Aust Inst ME, new series, No 14, and on p 326 expresses the opinion that the pipe or joint-veins (as at Irvine bank and Stannary Hills) were more valuable to follow than lodes in the granite in that district.GEOLOGY OF DISTRICTThe main feature of the area mapped is a band of altered sedimentary rocks which carry no fossils. It is a mile wide, and consists of a hard band of greywackes 200 ·t ·300 yds. wide, flanked on both sides by contorted shales which become more micaceous as the granite-area to the east is approached. The strata have a general strike of N. 30° W., with a steep westerly dip. A large area of acid intrusive rocks occurs to the west of this band. The outstanding feature of the district is a fault which cuts the sedimentary series in two, to the...

Jan 1, 1918

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Major mechanical components in the hoist and mechanical drive train are considered. Design and specification criteria based on American standards and practices are developed as they apply to typical mine hoist arrangements.

Jan 1, 1988

The paper outlines the history and current status of the VALMIN Code and sets out the background, methodology, results and recommendations of the Independent Review of the VALMIN Code undertaken during 2001 under the Chairmanship of Ian Goddard. The paper is based on the final report of the Taskforce, which was submitted to the Board of The AusIMM for consideration.

Jan 1, 2002

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By Karl Oltay

A series of 15, stations beginning with Potsdam and Budapest and ending with Budapest and Potsdam were occupied inn the period August, 1908, to January, 1909. The intermediate stations were all at points which had been connected by Baron Eötvös with torsion-balance traverses. The observations were made with an invariable pendulum of the standard four-pendulum type of instrument of the Geodetic Institute, made by Stückrath at Berlin-Friedenau. The observations at each of the field stations lasted-one to three days with one exception; two or three time determinations were made; four to eight series of pendulum observations were made; the error of determination of the elevation of the instrument above mean sea level ranged from 0.30 meter to 1.10 meters, with the exception of the Arad and Baja stations, where the elevation was known more accurately and averaged about ± 0.8 m, which would cause an error of ± 0.25 x 10-3 dynes. No topographic correction was applied. The values for ?g were taken from Eötvös: Report on Geodetic Observations in Hungary, especially Observations with the Torsion Balance, Budapest, 1910. The differences in ?g as determined, by the torsion balance and by the unvariable pendulum were: Kuvin-Hidegkut 1.2 km. 0.001, Livada-Kuvin 9 km. 0.001, Pankota-Livada 13 km. 0.004, Kuvin-Arad 20 km. 0.000, Pankota-Arad via Kuvin 42 42 km.0.005, Pankota- Arad via Kurtics 50 km.0.000 dynes. Oltay concludes that if the stations are close enough together and if the terrane is rather flat, the measurement of ?g with the Eötvös torsion balance is as accurate as with the invariable pendulum. -- Donald C. Barton.

Jan 1, 1929

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By John A. Breslin

The Bureau of Mines measured respirable dust in coal mines by means of multiple dust samplers worn by persons moving about the mines. The measurements were made primarily to evaluate the effectiveness of certain dust-control techniques; however, for this report, the data have been analyzed to determine the precision of the personal dust-sampling measurements. A total of 68 sets of measurements were available from multiple personal samplers. The measured dust masses were less than 1.0 mg because the sampling times were short. The coefficient of variation calculated from these data was 18.5 pct, compared with coefficients of variation ranging from about 10 to 30 pct, which were calculated from the most precise and extensive data available for fixed-point dust measurements made in coal mines. From this comparison, it is concluded that dust samplers worn by personnel are as precise as fixed-point samplers in measuring respirabe coal dust; the wearing of the samplers by someone moving about a mine does not contribute significantly to the variation in measurements made with these instruments.

Jan 1, 1983