Search Documents

Casing or lining pipe is used in boreholes for the following reasons:1. To preserve the hole while drilling and after it is finished.2. To shut water out of the hole or to isolate any particular water, gas, or oil-bearing stratum.Deep holes can seldom be drilled without casing, and only when in firm strata. If caving from the walls is at all likely while drilling, casing is necessary in order to prevent the tools horn being buried...

Jan 1, 1924

By Dorsey Lyon

I. INTRODUCTION. In presenting, this paper the writers wish to call attention first of all to the fact that the electric furnace was not developed as a competitor of the combustion furnace, but: 1. For the purpose of doing high-temperature work which it is not possible to do in the combustion furnace; and 2. For the treatment of ores from deposits which. are located in regions where fuel is scarce and costly, and where hydro-electric power is comparatively cheap, as is the case in Chili, in Canada, in certain parts of this country and Mexico.. This paper is not presented with the idea of trying to. prove that the electric furnace should replace the reverberatory or the blast furnace as used at present in the smelting of copper ores, but that it may be substituted for their in those localities which are not favorable to them,) and where either of the two following conditions may exist: (a) A district remote from railway transportation. facilities, and where there is a deposit, or deposits, containing sufficient values to warrant their being worked, but which, due to the cost of getting coke in for operating a smelter and of getting ore out to a smelter, have to remain unworked.. And where, on the other hand, there is plenty of water power which call he developed at reasonable cost for the production of electric power, by the use of which for. smelting the ores in an electric furnace, with subsequent Bessermerization if necessary, a concentrated product may be obtained, which can easily stand the necessary transportation charges. (b) Or,. comparatively speaking, the transportation facilities may be all right, but the cost of fuel be too great to permit of the ordinary methods of smelting, whereas,- on the other hand, hydro-electric power can he developed: in the district at a, low cost,, and the ores could be smelted by the electric furnace at a cost. that would make their treatment possible. With these possibilities in mind we have attempted to make a brief comparative study of the problem for the purpose of aiding those interested in the subject, in determining whether it would be possible metallurgically, and feasible commercially; to use the electric furnace-in those localities where, by reason: of excessive fuel costs, the cost, of operating the furnaces for smelting copper-ores. is either excessive or prohibitive. Although the smelting of copper ores in the electric furnace has received considerable attention and more or less experimental work has been done, so far as: we lire: aware there ate no electric furnaces in the United States which are' being worked on copper ores. In Norway, however, trial smeltings of copper ores with an electric furnace of 1,000 h. p. and an estimated producing' capacity of 2,000 tons per annum, have been

Jan 8, 1913

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By J. N. Geyer

During the early stages of the mining industry of the United States an apparently inexhaustible supply of high-quality, easily accessible coal made the product cheap and the attendant mining methods wasteful of recoverable coal. Because coal from advance places could be mined with less effort and a large outwit obtained as the entries advanced, much of the coal left in pillars to support the roof was lost. Squeezes often developed in these mined-over areas, or, if pillars were of sufficient size to-prevent squeeze, the roof would be so weakened by long exposure that any pillar recovery was extremely hazardous. As the value of unmined coal increased, a high recovery of the available coal became necessary. Numerous plans were tried during the period that followed, some of the methods proving successful while others were complete failures or only partly successful. As a better knowledge was pained of the roof strata and its behavior, however, pillar mining became more successful and methods suited to special roof conditions were developed.

Jan 1, 1933

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1974 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

By M. C. Harris

The past twenty to thirty years have seen unprecedented research activity aimed at understanding the performance of flotation froths. In 1990, Finch and Dobby coined the term froth recovery factor, Rr, to represent the efficiency of the froth in delivering particles from the pulp-froth interface to the concentrate. Originally defined for flotation columns, Rr has also been found useful in modeling mechanical flotation cells, and a number of techniques, based on quite different approaches, have been developed for measuring the froth recovery in industrial flotation cells. None of these techniques is universally successful. This paper reviews the concept of the froth recovery factor, and the basis of each of the techniques that have been proposed to measure Rr, and examines the reasons for this parameter being so difficult to pin down. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By C. O. Swanson

CALCULATING the average grade of a gold deposit is a problem that presents certain unique difficulties. Particularly troublesome is the fact that the average of the samples taken from a deposit is likely to be higher than the grade of the ore that is eventually mined, even when allowance is made for dilution and other factors resulting from the mining operations. It would seem that this situation is due to the presence in the deposits of structural peculiarities which have not been properly taken into account, since estimating the average grade of the broken ore produced from the deposits does not present the same difficulty. It is therefore evident that structural considerations are of prime importance in estimating the grade of a deposit. This fact is clearly realized and taken into account in cases where the boundaries of the orebodies and the variations within them are easily recognized. But in many gold deposits this condition is not satisfied, a circumstance which can be regarded as the main source of difficulty. Lacking definite information concerning the structure, we are apt to use certain procedures which are either empirical or based on general probabilities.

Jan 1, 1945

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

Since the introduction of water cooled test rings the operation of cupelling retort bullion has not alone been sImplified, but has also been the means of concentrating the bullion for the fining test in a much shorter time.The first water cooled test ring which I used was rectangular in shape, inside dimensions 5 ft. 3 in. x 2 ft. IQ in., and made of i in. mild steel plates, with a water space of 9i in. x 3t in. However, it was found that as soon as the filling commenced to wear and the litharge came in contact with the jacket, the plate was gradually affected on the lines of the wash, caused by the blast. After a while the inside steel plate went beyond the factor of safety, and was then substituted on the sides and the front of the test ring by a tin copper plate, which has stood now for the last five years without showing the least signs of wear or leakage.The test remains in use as long as the bottom is regarded as safe, and toward the end of the life of the test the litharge is allowed to work against the copper plate.

Jan 1, 1901

By Charles E. Locke

CONTINUED expansion of gold mining in 1935 led to further developments in treatment methods. In base metals and non-metallics progress is also noted, coincident with greater activity. Statistics are not available yet for 1935 but the trend is shown by 1934 when nonferrous ore mined in the United States was 35,840,737 tons, or 45 per cent more than in 1933. The amount concentrated was 27,167,530 tons or 75.80 per cent of the ore mined, and flotation was used in whole or part on over 96 per cent of the ore subjected to concentration. In the crushing field a new model of the Fahrenwald crusher is promised soon. The Symons fine-reduction cone crusher and Traylor secondary crusher continue to gain as intermediate crushers. A new book entitled "Crushers for Stone and Ore" by William T. W. Miller appeared. The Hadsel mill has been improved still further and a number of installations are in satisfactory operation showing economical power consumption and low wear. An attempt in a

Jan 1, 1936

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick's Law in 1947, through to today's models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.