Search Documents

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By Manuel Retamozo

El presente texto señala cómo el ejercicio físico adecuado y la dietética mejoran la producción y disminuyen el absentismo laboral en la empresa minera BHP Billiton Tintaya S.A a través de un política de prevención de salud. Entre los objetivos principales está determinar la frecuencia con que realizan ejercicio físico adecuado los trabajadores del área de mina, señalar si existieron cambios en las costumbres alimenticias de los trabajadores del área de mina después de la educación alimentaria, delimitar si existe asociación entre el aumento de la producción en el área de mina con la práctica del ejercicio físico adecuado y la dietética, así como entre la disminución del absentismo laboral en el área de mina con tales prácticas.

Jul 31, 2003

By Silvana Costa

Rapid changes in technology and human resources trends require the mining industry to plan carefully for new work camps. The abandonment of the “mining town” concept and rapid increases in the adoption of long distance commuting have intensified the need for improved planning and monitoring of existing and upcoming operations. New mines will have an increasing Aboriginal participation in their workforce and will mostly to be located in remote and in extreme weather conditions. In this sense, the intensification of the use of the commuting system has increased the need for improved planning and monitoring of upcoming operations. Given that mining development is experiencing a surge in activity in Canada, particularly in remote and northern locations significant number of individuals will get jobs that involve mine camp communities. Some employees will spend half of their working lives at the mine site for a period of time that can last up to 30 years. Even though investments have been made towards particularly high quality physical environments, mine camp policies, programs and employee quality of life in mine camps have not been studied in any depth.

Sep 12, 2005

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand&apos;s mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand&apos;s prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors&apos; perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand&apos;s mineral resources.

Jan 1, 2000

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By D. J. Goodings, R. J. Bonenberger, H. U. Leiste, W. L. Foumey

This paper describes a series of two-dimensional tests conducted and filmed with a high-speed (500 frames per second) video camera. The purpose of these tests was to provide a better understanding of the processes involved in creating craters and channels in water covered soils with explosives.

Jan 1, 2000

By Barnard Foo

Topics of Discussion ?Location ?Production & Mining Operation ?Mineralization ?Mining Method ?Rock Mechanics Issues ?Ground Control Problems ?Numerical Analysis ?RockmassBehaviour ?Conclusions & Recommendations ?Discussion

Feb 1, 2008

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

ALTHOUGH the development of the various flotation processes during the last 8 years has been so revolutionary, this development has been, until recently, entirely confined to the separation of the gangue from the mixed metalliferous sulphides.The desirability of finding some method of separating the independent sulphides from such a miXture, by means of flotation, has long been recognized. ThIS need was emphasized when the slimes resulting from the grinding of Broken Hill sulphide ores were for the first time successfully dealt with by the Mineral Separation Company&apos;s process on the Central mine. This process proved the practicability of separating the sulphides of lead and zinc as a mixed concentrate from the gangue present in slime. Although this was a very notable achievement, the process has not been generally used, owing to the mixed lead and zinc concentrates resulting from the treatment being acceptable neither to the zinc nor the lead smelters.Although the introduction of eucalyptus oil in minute quantities as an emulsifying agent has simplified the work of the subsequent tabling of mixed sulphide concentrates, rendering unnecessary the burning off or removal of the oil, there will always be a considerable quantity of slimy product too fine to settle on the moving surface of the concentrating machines, and therefore requiring other means for its division into lead and zinc concentrates.

Jan 1, 1912

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because &quot;the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By A. Dale Wunderlich

Since Sept. 11, 2001, the author has been asked by several mining companies and mining publications to share some of his insights on how the terrorist attacks on the World Trade Center (WTC) and Pentagon might affect the mining industry globally. Until now, the author has been reluctant to express his thoughts in a publication that could possibly fall into the hands of terrorists and give them some ideas that they may not have been previously considering. However, the author discussed the contents of this article with several friends and acquaintances in the international intelligence community. They said that nothing commented on here is new to the terrorists. Potential terrorist targets Sources within the worldwide intelligence gathering community have told the author that current intelligence data indicates that it is likely that the Islamic fundamentalist groups responsible for the attacks on Sept. 11, 2001will likely be directing their effort at foreign business entities. Any overseas or any domestic businesses of highly visible companies that are part of the anti-terrorism alliance should consider themselves a potential target.

Jan 1, 2002

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001