Search Documents

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner's team.

Jan 1, 2013

Study on Dynamic Characteristics of Inertia Cone Crusher and Its Application

Sep 13, 2010

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

By COLIN A. LAWRENCE, Anthony Del Vescovo

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2017

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By William B. Plank

IN this paper are presented the results of a complete statistical survey of the enrolment, courses and degrees, and the employment situation of recent graduates in all of the 46 institutions in the United States, including Alaska, and four of the six schools in Canada that grant degrees in mineral technology. The data were collected by the writer by means of a questionnaire in December, 1933, to which all the institutions, except one, replied. Included also are data of a similar study made by the writer in May, 1933, for the S. P. E. E. summer session of mining and metallurgical teachers at the University of Wisconsin and published in the Journal of Engineering Education for December. 1933. Some of the data of a paper of the writer's entitled, "The Trend of Mineral Engineering Student Enrolment in the United States," read at the A. I. M. E. meeting on Feb. 16. 1931, are given for comparison. Acknowledgment is made to all the administrative officers of the institutions who took the time from their busy lives to supply the in- formation asked for. Their fine cooperation has alone made possible these two surveys with a completeness of detail never before attempted

Jan 1, 1934

This dictionary is published by the Bureau of Mines as a contribution to the mining and mineral literature in the belief that it will fill a recognized need. Several attempts have been made over the years to revise Albert Fay's Glossary of the Mining and Mineral Industry which first appeared in December of 1918. Frank L. Hess of the Bureau of Mines worked on a revision, but his untimely death prevented its completion. Subsequently, the writer was employed to compile and edit this dictionary in cooperation with the technical staff of the Bureau of Mines. Fay's glossary contained about 18,000 terms with 27,000 definitions; the present compilation contains about 55,000 terms with approximately 150,000 definitions. These terms are of both a technical and local nature, and they apply to metal mining, coal mining, quarrying, geology, metallurgy, ceramics and clays, glassmaking, minerals and mineralogy, and general terminology. Petroleum, natural gas, and legal mining terminology, unless of a general nature, has been excluded, as has been foreign terminology where there is an English equivalent. Several thousand Spanish-American mining terms that appeared in Fay's compilation have been removed to make way for the thousands of new English terms that have evolved over the years. Those Spanish-American and Mexican terms still used in the Southwestern United States have been retained.

Jan 1, 1968

By William R. Hardwick

Present information indicates that a copper deposit can be safely fractured with a nuclear explosive and the copper successfully recovered by the in-situ leaching method. The process is not yet at the stage where it can be presented t ) the mining industry as a technique proven in all its aspects, but it is a method with high success potential. Unknown factors must be evaluated by a full-scale test before the economics or the extent of the use of the method by the mining industry can be predicted. Preliminary calculations indicate that the cost of fracturing a copper deposit nuclear explosives may range from l.8 to 55.2 cents per ton or in some case: less than a cent per pound of recoverable copper. Copper may be recovered at less cost than by conventional methods. Deposits with 4 pounds of recoverable copper may be economic and production from a deposit may begin in less than half the time required for conventional methods.

Jan 1, 1967

By BRETTMANN TRACY

Jan 1, 2000

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Montieello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By Christopher B. Kapes

To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.

Jan 1, 1994

By Silvio Hernández Aquije

El presente texto señala el descubrimento del yacimiento vanadífero de Minasragra a través del reporte de Yeatman-Berry en 1916 y el de Kett-Sproul en 1931. Así también señala los tipos de mineralización como la mineralización primaria y por impregnación.

Jul 1, 1955

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By S. J. Hussey

This Bureau of Mines report presents a discussion of the statistical approach to the design of experiments and indicates, by concrete examples, how and when statistical design is essential for obtaining meaningful data with a minimum number of experiments. Every research worker plans his work and designs his experiments in a manner which, based on his experience, seems most rational to him and which he believes will produce the information essential for resolving the problems. If the results obtained are open to multiple interpretations and are not of definitive reliability, the failure of the experiment design to produce the desired information may be due to several causes, These include faulty judgment in selecting the factors to be tested, ignoring the importance of interaction between factors, failure to adequately control test variables, and assuming that meaningful trends in the results can be identified without comparison to a predetermined experimental error. An experienced researcher probably will deduce from the nature of the data obtained that the design is faulty and may by trial and error ultimately arrive at the correct solution to the problem. Statistical methods of planning research minimize the chance of faulty experiment design, embody concrete procedures for testing the validity and reliability of the test data and for indicating mandatory changes in the design, and enable the researcher to obtain meaningful information with the least number of tests.

Jan 1, 1963

By Robert C. Merritt

Laboratory amenability studies as well as a pilot heap-leaching investigation of low-grade sandstone uranium ores from Wyoming, New Mexico, and Colorado are described. Sulfuric acid heap leaching with oxidation, for 120 days, extracted up to 98 percent, 90 percent, and 79 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively.

Jan 1, 1976

Another major aluminum company announced intentions to follow other domestic producers recent price actions by raising its unalloyed ingot quotes by 3¢ to 44¢ per pound, effective June 1, 1976. COBALT: All final data for 1975 are included in the table for cobalt on page 23. Demand in March increased significantly for the second month in a row, signaling a recovery from the previous year's relatively low demand levels. Imports of cobalt tripled in March over those of February. This should partially offset reduced sales of cobalt excesses from the National Stockpile. Import projections for the next several months have been lowered because transportation difficulties in Zaire are expected to result in reduced shipments.

Jan 1, 1976