Search Documents

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

Application of Discrete Element Method for Simulating Feeding Conditions and Size Reduction in Cone Crushers

Sep 13, 2010

Kidd Mine in Northern Ontario is now producing from Stage 1 of the Mine D expansion project ? mining between 2100 m and 2700 m below surface. Planning for Stage 2 of the Mine D project is already well advanced and will see the mine extended potentially to 3100 m below the surface. To ensure adequate ventilation is maintained at such depths, two large axial fans have been installed on the 6000 Level (1800 m below surface) as exhaust booster fans to operate in series with the surface exhaust fans. The Kidd Mine 6000 Level Booster Fans are a unique installation with unique and often unexpected challenges. These challenges have been met and attacked through the combined efforts of mine and fan manufacturer personnel with a common focus.

Jan 1, 2009

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By V. McLemore, N. Dunbar, K. Donahue

There are three principle lines of evidence that indicate the clay minerals found in the Goathill North (GHN) rock pile at the Molycorp mine are predominantly a product of hydrothermal alteration, not weathering. The unweathered drill core and samples from GHN have similar types and abundances of clay-mineral groups based on XRD analysis. Chemical analyses from the electron microprobe reveal similar chemical compositions for the hydrothermal alteration clays in drill-core samples and clays found in the rock pile. Textural evidence gathered from petrographic and microprobe examination also suggests a hydrothermal origin for clay minerals.

Jan 1, 2007

Underground equipment owners and users in order to compete and succeed in being viable business propositions must continually balance costs with productivity. By reducing their hourly ownership, operation and maintenance costs and increasing their hourly production, the cost per unit of material mined will be optimized.

Jan 1, 1990

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013

By N. E. Mkadmi

Backfilling increases the stability of underground stopes and may help reduce the environmental footprint from the mining operation. The barricades holding the backfill in place must be designed to prevent failure based on the total and effective stress states, which depend on fill properties, stope geometry, and filling rate. This paper presents results from a numerical study aimed at analyzing the stress states associated with the response of paste backfill following stope filling, with an emphasis on the short term behavior. The simulations illustrate how stresses evolve with backfill drainage and filling rate in a vertical stope.

May 1, 2011

Minerals are fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels?mining, processing and manufacturing finished products. The estimated growth rate for the real GDP of the United States was 2.1 percent and the nominal GDP was about $13.8 trillion in 2007 (Table 1). The prime interest rate decreased to 7.25 percent in December from 8.25 percent at the beginning of 2007, reflecting actions taken by the Federal Reserve Board to counter financial difficulties surrounding subprime mort-gages. Delinquencies on subprime mortgages increased throughout the year, affecting not only the delinquent home owners but also financial instruments invested in mortgage-backed securities. The average contract mortgage rate for the purchase of previously occupied homes in the United States was 6.35 percent in November; a slight decrease from 6.37 percent in January but still greater than 5.34 percent reported in July 2003, the lowest rate in the past five years. With the tightening of credit, the seasonally adjusted annualized rate for new privately owned housing starts declined 27 percent from December 2006 to November 2007. The loss in the residential market was balanced by a 9-percent increase in nonresidential construction between January and August 2007, during which slight increases occurred in nearly all

Jan 1, 2008

By D Craw, J Youngson

Recent exploration for mesothermal gold deposits in the Otago Schist has focussed largely on extensions of, or analogies to, the reverse fault-hosted Hyde-Macraes Shear Zone deposit. Abundant normal fault-hosted mesothermal and epithermal vein deposits in the Otago Schist have attracted less attention, largely because they have limited lateral extent and steeper dips. Northwest-striking normal fault-hosted vein sets near Barewood and Hindon in east Otago crosscut schist foliation on the Barewood-Hindon plateau at a high angle along a combined strike length in excess of 20 kilometres. The trend of the vein sets is not linear, but rather contains several right lateral steps. Almost all veins dip steeply to the northeast. Angular discordance between schist foliation and the plateau surface along the trend increases from near zero at the northwest end of the veins to about 30¦ at the southeast end. Crude formation depth estimates decrease from about 7.5 km at the Barewood end of the zone to

Jan 1, 2002

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP.Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, OOP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the OOP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923