Search Documents

By Kenji Morinaga, Hiromichi Takebe

"Ge-S binary glasses in the range 57 to 90 at %S at 0.5 to 3 at %S intervals were prepared by a conventional melting technique using fused quartz ampoules as melting containers. Impurities contaminated during preparation process are evaluated by IR spectroscopy. The causes of impurity contaminations are discussed. Density data in a systematic series of Ge-S glasses is demonstrated. IntroductionSulfide glasses are of particular interest for new laser and nonlinear optical materials in the near-infrared and infrared regions [1]. Sulfide glasses have the features of low-phonon-energy and high refractive index with moderate rare-earth ion solubility. The low-phonon-energy is favorable for the reduction of nonradiative rate for the emission of rare-earth ions. The high refractive index results in a high radiative-rate and in a high third-order nonlinearity. However, impurities may degrade the superior optical properties of sulfide glasses.In this work Ge-S glasses were prepared by a conventional melting technique. Impurities contaminated during the preparation process are evaluated and their causes are discussed for future improvements. The measured densities of Ge-S glass samples were compared with the results of previous studies [2], [3]. Ge-S glasses have some favorable properties for practical .applications including non-toxicity, good thermal and chemical stabilities."

Jan 1, 2000

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By Mao Chen, Baojun Zhao, Zhixiang Cui

Bottom blown oxygen copper smelting process, operated at high grade matte (up to 75 wt% Cu) with relatively low (2-3 wt%) Cu in slag, has been commercialized for more than five years at Dongying Fangyuan Nonferrous Metals CO., Ltd. Quenched slag and matte samples have been collected at different operating conditions while the slag temperature was measured by thermocouple. The samples were analysed by X-ray Fluorescence and Electron Probe X-ray Microanalysis. FactSage computational software was used to explain the observations of the industrial samples. The analyses show that the copper loss was closely related to the operation parameters. The Fe/SiO2 in slag and temperature determine the solid proportion, which significantly affects the physical entrained and also chemically dissolved copper in the slag. The present study will be useful in understanding the slag chemistry of bottom blown copper smelting furnace and in optimization of the operating conditions to lower Cu loss in the slag.

Jan 1, 2015

By Gary Kordosky

Equilibrium modifiers, first introduced into copper solvent extraction reagents in the late 1960?s, are widely used. The properties of various equilibrium modifiers with respect to copper extraction, selectivity, reagent stability and entrainment are discussed and some conclusions are drawn relating the structure of the modifier to the properties of the modifier. A new highly selective, low viscosity modifier is also introduced.

Jan 1, 2003

By R. P. King

The linear intercept distributions provide unambiguous and accurate characterizations of the texture of mineralogical materials. The relation between the measured linear intercept distributions and the spatial correlation function is shown to be given by: in the Laplace Transform domain. The linear intercept distributions of the two phases in a low- grade chromite-serpentinite ore were measured. and the spatial correlation functions for both phases were evaluated using the above relation. The correlation functions are the primary relations for integral geometric models of mineralogical texture and this work demonstrates the relation between the 10 stereological model and the 3D integral geometry model for mineral liberation.

Jan 1, 1991

By Xianwen Dai

One of the biggest challenges for the gold industry in the 21st century is the presence of copper in gold containing ore bodies. This is because copper consumes large quantities of cyanide. In addition, copper cyanide species are more stable than free cyanide, and hence are problematic in events of tailings spillage. The present paper compares cyanide and thiosulfate leaching for the recovery of gold from a copper containing ore. For cyanide leaching, the extraction of gold using copper cyanide complexes instead of free cyanide was tested in the presence and absence of added ammonia. For the thiosulfate leaching, the effect of the minerals present in the ore on the solution potential and thiosulfate consumption are illustrated.

Jan 1, 2003

By J. Fogarty, J. Sofra

The mobile telecommunications sector is one of the fastest growing industries worldwide. However, increasingly stringent environmental regulations are placing pressure on manufacturers to accept responsibility for end of life products. The companies are therefore exploring avenues to recover the valuable components contained within the mobile telecommunications devices thus reducing the quantities of toxic components going to landfill. Batteries used to power the devices, are typically based on either nickel-cadmium, nickel metal hydride, or lithium ion cells. They contain toxic metals including nickel, cadmium, lithium, potassium, lead, and cobalt in a complicated arrangement of battery cells surrounded by a metals then plastic casing. The Ausmelt Catalytic Waste Converter (CWC) for waste treatment and recycling is well suited to processing all three mobile phone battery types for the recovery of valuable metals in marketable products that can be recycled to industry without turning out harmful levels of toxic emissions. Ausmelt recently demonstrated the capabilities of its CWC by continuously processing 4.5 tonnes of nickel-cadmium batteries. Using Ausmelt's pilot plant facility in Australia, the nickel-cadmium batteries were processed to produce a nickel iron sulphide (matte), a cadmium fume and a final slag which satisfied CS toxicity leach test criteria and was safe f<~r disposal to landfill. This paper explores the commercial development of the Ausmelt CWC for treating each of the three battery types in light of (a) the outcomes of the recent demonstration, and (b) the current and expected future availability of batteries for processing.

Jan 1, 2000

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By Larry G. Stolarczyk

The development of geosteering technology for geothermal reservoirs is challenged by the integration of electrically small antennas in small-diameter metallic drill rods. To be useful, the antenna pattern must achieve sufficient back-lobe suppression, preferably with a forward-looking pattern. Forward-looking capability requires an antenna array with phase control. The phase-controlled antenna pattern enables imaging of geologic structures ahead of and surrounding the well bore. This paper describes the development of electric and magnetic dipole arrays for small-diameter drilling pipe.

Jan 1, 2006

By Yuri Gelfgat

"This paper presents some results of the investigation of the steady magnetic field influence on hydrodynamics and heat/mass transfer in processes of semiconductor single crystal growth (Si, Ge, InSn). The investigation employed mathematical and physical simulation techniques of relevant processes and full-scale experiments on growth facilities. A number of additional MHD phenomena have been found generated in the melt due to the rearrangement of flow pattern, the formation of specific convective cells, and the origin of MHD boundary and shift layer.IntroductionMagnetohydrodynamic (MHD) means of creating forces by contact-free methods in liquid conducting media have been widely used in the production of volume semiconducting single crystals. The goal of this method is to control convective transfer processes in the melt volume and on the crystallization front [1-3]. This is due to the sufficiently high conductivity of semiconductor melts (s = 104 /106 O1m-1 ) and an obvious relationship between the hydrodynamics in the melt and at interfaces and the conditions of formation of single crystals and their quality [ 1].All types of MHD effects rest upon the generation of volume electromagnetic forces in the melt by various means as well as on the possibility to direct them arbitrary in space and to adjust easily their absolute values. Fig. l presents different means how to implement MHD phenomena during single crystal growth. It should be emphasized that in all the modifications given in Fig. l additional energy introduced into the melt cannot influence directly the crystallization process since it is incomparable to the energy of molecular forces. Both the influence and efficiency of MHD means are determined solely by the change of motion, heat and mass transfer characteristics."

Jan 1, 1998

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By William Bourcier

Geothermal Brines are a significant potential source of valuable minerals and metals. These brines are water that is heated by the natural heat flow from the depths of the earth. Hotter brines, typically with temperatures greater than 120°C, are used to generate electricity. Lower temperature brines are directly used to supply thermal energy to applications such as agriculture, aquaculture and process/domestic heat. The geothermal waters have had intimate and lengthy contact with the layers of the earth?s crust that they flow through, resulting in dissolution of minerals and metals from the rocks, and solution into the hot water. These aqueous solutions can be processed to recover minerals and metals. Some potential products include silica, zinc and lithium, along with other materials. Recovery of minerals and metals from geothermal brines can be viewed as ?solution mining by nature?, followed by application of known or new hydrometallurgical techniques for isolation and purification. This paper discusses the opportunities, the processes, the challenges, the current status, the economics and the potential for recovery of minerals and metals from geothermal brines.

Jan 1, 2006

By K. B. Dotson

A common international safety and health management system was developed. Analysis of selected major safety and health management systems from around the world was conducted. Functional elements of selected systems were grouped to identify common elements and key differences. Common elements were subjected to qualitative judgments of equivalency and then reconciled. With few exceptions, differing elements were revised to achieve cultural neutrality. The resulting 98 system elements were organized according to the NOSA numbering and title scheme. System summaries were produced in Spanish and English. A pre-implementation self-assessment evaluated conformance in three distinct cultures. The consensus 98 element system was internally named the BHP Copper Five Star Safety System Performance Management Guidelines. Development of a common system within an organization with international operations can enhance the ability of the staff function to share resources, programs and subsystem improvements and thereby increasingly protect workers. Common systems can increase the level of management support by demonstrating increased compatibility of the safety and health management function with traditional business objectives. Safety professionals, industrial and occupational hygienists, business managers and the safety and health of workers will benefit from further development and articulation of common systems for safety and health management.

Jan 1, 1999

By Jin Liu

To improve value metals recovery, a new operating concept for the Inco flash furnace was investigated, in which the flash furnace coke addition practice would aim at establishing a reducing barrier on the surface of the molten bath. The descending partially oxidized sulfide mineral particles would reach the supernatant coke layer prior to the formation of slag. The key for success depends on the effectiveness of the coke layer to produce a sulfur deficient matte while maintaining furnace production capacity. The mechanism and rate of carbon reduction of the phases formed in the flash flame, i.e. sulfide (matte) and oxysulfide was investigated by means of crucible graphite reduction test work. The objective of these tests was to measure the rate of solid graphite reduction of matte, oxysulfide, slag, and matte+slag mixture at different temperatures. These tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions, reduced material assays, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By M. Hadj Meliani

This paper explores direct use of finite element analysis by CASTEM 2000 in order to determine the evolution of T-stress term for arc of pipe specimens with external surface crack. A simple method, called the stress difference method proposed by Yang (1999), is used to compute the elastic T-stress in mode I at a crack tip. The different crack geometries and length-to-thickness ratio on T-stress and stress-intensity factor (SIF) are examined. The revisited stress difference method is shown to be an accurate and robust scheme for evaluating T-stress in arc of pipe.

Jan 1, 2006

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011